FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Gentoo > Gentoo User

 
 
LinkBack Thread Tools
 
Old 11-23-2007, 02:57 PM
pk
 
Default Usb device not accepting address x, error -71

Neil Bothwick wrote:
> On Thu, 22 Nov 2007 22:07:35 +0100, pk wrote:
>
> How did you configure this kernel? By using an old .config with make
> oldconfig or doing it from scratch?

By using an old .config and doing an make oldconfig. After this:
make menuconfig and going over the setup to see if I need to change
anything (I always change local version to compile date + add. info, if
needed).

> What does the system log show when you connect the drive (tail
> -f /var/log/messages)?

Well, believe it or not; it works perfectly today... Very strange,
especially since I have _not_ changed anything!

The messages I got are nearly identical (address may not be the same) to
this output (googled):

usb 3-1: new high speed USB device using ehci_hcd and address 4
usb 3-1: device descriptor read/64, error -71
usb 3-1: device descriptor read/64, error -71
usb 3-1: new high speed USB device using ehci_hcd and address 5
usb 3-1: device descriptor read/64, error -71
usb 3-1: device descriptor read/64, error -71
usb 3-1: new high speed USB device using ehci_hcd and address 6
usb 3-1: device not accepting address 6, error -71
usb 3-1: new high speed USB device using ehci_hcd and address 7
usb 3-1: device not accepting address 7, error -71

After these the following messages showed up in my kernel log (also
googled):

USB 1-2: Device not accepting address 2, error -71
(repeats several times trying different addresses)

My chipset is i875p (motherboard is Abit IC7 max3) and I have UCHI and
EHCI compiled into the kernel (as well as usb mass storage driver and
whatnot). The strange thing is that this setup has worked flawlessly
until yesterday. And now it seems to work ok again. Log output:

usb 1-4: new high speed USB device using ehci_hcd and address 3
usb 1-4: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
scsi 4:0:0:0: Direct-Access Maxtor 6 L200R0 BAH4 PQ: 0 ANSI: 0
sd 4:0:0:0: [sde] 398297088 512-byte hardware sectors (203928 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sde] Assuming drive cache: write through
sd 4:0:0:0: [sde] 398297088 512-byte hardware sectors (203928 MB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sde] Assuming drive cache: write through
sde: sde1
sd 4:0:0:0: [sde] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg4 type 0
usb-storage: device scan complete

Ah, well. Until next time I guess...

Thanks for your interest and support!

Best regards

Peter K
--
gentoo-user@gentoo.org mailing list
 

Thread Tools




All times are GMT. The time now is 08:34 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org