FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Redhat > Fedora Development

 
 
LinkBack Thread Tools
 
Old 11-24-2008, 02:11 PM
Jos Vos
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

Hi,

On a somewhat special piece of hardware (point-of-sale hardware) where
I can successfully run RHEL4 and RHEL5, I can't get F9 or F10 working
w.r.t. graphics. That is, I just get a black screen, X doesn't die!
I've now installed F10 (text mode installer).

I did not try Fedora on that hardware until recently and after it failed,
I decided to wait till F10, without luck.

The "lspci -v" output for the VGA card is:

00:02.0 VGA compatible controller: Intel Corporation 82915G/GV/910GL Integrated Graphics Controller (rev 0e) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation 82915G/GV/910GL Integrated Graphics Controller
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
I/O ports at ff00 [size=8]
Memory at d0000000 (32-bit, prefetchable) [size=256M]
Memory at fdf80000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Kernel modules: intelfb

The last "(EE)" message from Xorg.0.log is:

(EE) intel(0): Bad VBT signature

I can send the full Xorg.0.log if needed, but I didn't want to spam
the list with that right now.

Any suggestions?

Thanks,

--
-- Jos Vos <jos@xos.nl>
-- X/OS Experts in Open Systems BV | Phone: +31 20 6938364
-- Amsterdam, The Netherlands | Fax: +31 20 6948204

--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 02:16 PM
"Aioanei Rares"
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, Nov 24, 2008 at 5:11 PM, Jos Vos <jos@xos.nl> wrote:

Hi,

On a somewhat special piece of hardware (point-of-sale hardware) where
I can successfully run RHEL4 and RHEL5, I can't get F9 or F10 working

w.r.t. graphics. *That is, I just get a black screen, X doesn't die!
I've now installed F10 (text mode installer).

I did not try Fedora on that hardware until recently and after it failed,
I decided to wait till F10, without luck.


The "lspci -v" output for the VGA card is:

00:02.0 VGA compatible controller: Intel Corporation 82915G/GV/910GL Integrated Graphics Controller (rev 0e) (prog-if 00 [VGA controller])
* * * *Subsystem: Intel Corporation 82915G/GV/910GL Integrated Graphics Controller

* * * *Flags: bus master, fast devsel, latency 0, IRQ 16
* * * *Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
* * * *I/O ports at ff00 [size=8]
* * * *Memory at d0000000 (32-bit, prefetchable) [size=256M]

* * * *Memory at fdf80000 (32-bit, non-prefetchable) [size=256K]
* * * *Capabilities: [d0] Power Management version 2
* * * *Kernel modules: intelfb

The last "(EE)" message from Xorg.0.log is:


* *(EE) intel(0): Bad VBT signature

I can send the full Xorg.0.log if needed, but I didn't want to spam
the list with that right now.

Any suggestions?

Thanks,

--
-- * *Jos Vos <jos@xos.nl>

-- * *X/OS Experts in Open Systems BV * | * Phone: +31 20 6938364
-- * *Amsterdam, The Netherlands * * * *| * * Fax: +31 20 6948204

--
fedora-devel-list mailing list
fedora-devel-list@redhat.com

https://www.redhat.com/mailman/listinfo/fedora-devel-list

Try vesa.
--
Aioanei Rares

schaiba@fedoraproject.org
"China is a big country, inhabited by many Chinese." --Charles de Gaulle


--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 02:43 PM
Jos Vos
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, Nov 24, 2008 at 05:16:52PM +0200, Aioanei Rares wrote:

> Try vesa.

Does not work either:

(II) Loading /usr/lib64/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org Video Driver, version 4.1
(II) VESA(0): initializing int10
(WW) VESA(0): Bad V_BIOS checksum
(II) VESA(0): Primary V_BIOS segment is: 0xc000
c000:2719: 01 ILLEGAL EXTENDED X86 OPCODE!
(II) VESA(0): VESA BIOS not detected

This remembers me to the fact that I had once submitted

https://bugzilla.redhat.com/show_bug.cgi?id=339361

That was closed because I didn't have HW free for further testing.
This is similar, although at that time it gave this problem for
the i810 driver.

I tried to install 32-bit F10, but the graphical installer doesn't
work either. I can install that in text mode, to see what happens
afterwards.

--
-- Jos Vos <jos@xos.nl>
-- X/OS Experts in Open Systems BV | Phone: +31 20 6938364
-- Amsterdam, The Netherlands | Fax: +31 20 6948204

--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 03:50 PM
Adam Jackson
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, 2008-11-24 at 16:11 +0100, Jos Vos wrote:

> The last "(EE)" message from Xorg.0.log is:
>
> (EE) intel(0): Bad VBT signature
>
> I can send the full Xorg.0.log if needed, but I didn't want to spam
> the list with that right now.

Typically the VBT signature doesn't mean much. But yes, full log would
be interesting.

- ajax
--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 03:57 PM
Jos Vos
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, Nov 24, 2008 at 11:50:24AM -0500, Adam Jackson wrote:

> Typically the VBT signature doesn't mean much. But yes, full log would
> be interesting.

I tried with 32-bit: still no graphics.

Attached:
- Xorg.0.log.vesa (no xorg.conf or xorg.conf specifying "vesa") and
- Xorg.0.log.intel (with xorg.conf specifying "intel").

This is all on 32-bit F10 (final release).

--
-- Jos Vos <jos@xos.nl>
-- X/OS Experts in Open Systems BV | Phone: +31 20 6938364
-- Amsterdam, The Netherlands | Fax: +31 20 6948204

X.Org X Server 1.5.3
Release Date: 5 November 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-92.1.10.el5 i686
Current Operating System: Linux louie.xos.nl 2.6.27.5-117.fc10.i686 #1 SMP Tue Nov 18 12:19:59 EST 2008 i686
Build Date: 16 November 2008 08:29:02PM
Build ID: xorg-x11-server 1.5.3-5.fc10
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Nov 24 17:08:18 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section. Using the first Screen section.
(==) No screen section available. Using defaults.
(**) |-->Screen "Default Screen Section" (0)
(**) | |-->Monitor "<default monitor>"
(==) No device specified for screen "Default Screen Section".
Using the first device section listed.
(**) | |-->Device "Videocard0"
(==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified. Using compiled-in default.
(==) FontPath set to:
catalogue:/etc/X11/fontpath.d,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81f4400
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 4.1
X.Org XInput driver : 2.1
X.Org Server Extension : 1.1
X.Org Font Renderer : 0.6
(II) Loader running on linux
(--) using VT number 7

(--) PCI:*(0@0:2:0) Intel Corporation 82915G/GV/910GL Integrated Graphics Controller rev 14, Mem @ 0xfdf00000/0, 0xd0000000/0, 0xfdf80000/0, I/O @ 0x0000ff00/0
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) LoadModule: "extmod"

(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SELinux
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"

(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"

(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(==) AIGLX enabled
(==) Exporting typical set of GLX visuals
(II) Loading extension GLX
(II) LoadModule: "freetype"

(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.5.3, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "dri"

(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "vesa"

(II) Loading /usr/lib/xorg/modules/drivers//vesa_drv.so
(II) Module vesa: vendor="X.Org Foundation"
compiled for 1.4.99.905, module version = 1.3.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 4.1
(II) VESA: driver for VESA chipsets: vesa
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"

(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.1.0
ABI class: X.Org Video Driver, version 4.1
(II) Loading sub module "int10"
(II) LoadModule: "int10"

(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org Video Driver, version 4.1
(II) VESA(0): initializing int10
(WW) VESA(0): Bad V_BIOS checksum
(II) VESA(0): Primary V_BIOS segment is: 0xc000
c000:2719: 01 ILLEGAL EXTENDED X86 OPCODE!
(II) VESA(0): VESA BIOS not detected
(II) UnloadModule: "vesa"
(II) UnloadModule: "int10"
(II) Unloading /usr/lib/xorg/modules//libint10.so
(II) UnloadModule: "vbe"
(II) Unloading /usr/lib/xorg/modules//libvbe.so
(EE) Screen(s) found, but none have a usable configuration.

Fatal server error:
no screens found

X.Org X Server 1.5.3
Release Date: 5 November 2008
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.18-92.1.10.el5 i686
Current Operating System: Linux louie.xos.nl 2.6.27.5-117.fc10.i686 #1 SMP Tue Nov 18 12:19:59 EST 2008 i686
Build Date: 16 November 2008 08:29:02PM
Build ID: xorg-x11-server 1.5.3-5.fc10
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Nov 24 17:07:11 2008
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section. Using the first Screen section.
(==) No screen section available. Using defaults.
(**) |-->Screen "Default Screen Section" (0)
(**) | |-->Monitor "<default monitor>"
(==) No device specified for screen "Default Screen Section".
Using the first device section listed.
(**) | |-->Device "Videocard0"
(==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
(==) Automatically adding devices
(==) Automatically enabling devices
(==) No FontPath specified. Using compiled-in default.
(==) FontPath set to:
catalogue:/etc/X11/fontpath.d,
built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Open ACPI successful (/var/run/acpid.socket)
(II) Loader magic: 0x81f4400
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.4
X.Org Video Driver: 4.1
X.Org XInput driver : 2.1
X.Org Server Extension : 1.1
X.Org Font Renderer : 0.6
(II) Loader running on linux
(--) using VT number 7

(--) PCI:*(0@0:2:0) Intel Corporation 82915G/GV/910GL Integrated Graphics Controller rev 14, Mem @ 0xfdf00000/0, 0xd0000000/0, 0xfdf80000/0, I/O @ 0x0000ff00/0
(II) System resource ranges:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) LoadModule: "extmod"

(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension SELinux
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"

(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"

(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(==) AIGLX enabled
(==) Exporting typical set of GLX visuals
(II) Loading extension GLX
(II) LoadModule: "freetype"

(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 1.5.3, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.6
(II) Loading font FreeType
(II) LoadModule: "dri"

(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org Server Extension, version 1.1
(II) Loading extension XFree86-DRI
(II) LoadModule: "intel"

(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 2.5.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 4.1
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
965GM, 965GME/GLE, G33, Q35, Q33,
Mobile Intel® GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
(II) resource ranges after probing:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"

(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 0.1.0
ABI class: X.Org Video Driver, version 4.1
(II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (==) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 915G
(--) intel(0): Chipset: "915G"
(--) intel(0): Linear framebuffer at 0xD0000000
(--) intel(0): IO registers at addr 0xFDF00000
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(EE) intel(0): Bad VBT signature
(WW) intel(0): VBIOS initialization failed.
(==) intel(0): Using EXA for acceleration
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA has no monitor section
(II) intel(0): I2C bus "SDVOCTRL_E for SDVOB" initialized.
(II) intel(0): I2C device "SDVOCTRL_E for SDVOB:SDVO Controller B" registered at address 0x70.
(II) intel(0): I2C bus "SDVOB DDC Bus" initialized.
(WW) intel(0): SDVOB: Unknown SDVO output type (0x4000)
(II) intel(0): Output Unknown-1 has no monitor section
(II) intel(0): SDVOB: device VID/DID: 02:41.01, clock range 25.0MHz - 200.0MHz
(II) intel(0): SDVOB: 1 input channel
(II) intel(0): SDVOB: LVDS0 output reported
(II) intel(0): Current clock rate multiplier: 2
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID for output VGA
(II) intel(0): I2C device "SDVOB DDC Bus:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "SDVOB DDC Bus:ddc2" registered at address 0xA0.
(II) intel(0): EDID for output Unknown-1
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): Not using default mode "640x350" (vrefresh out of range)
(II) intel(0): Not using default mode "640x400" (vrefresh out of range)
(II) intel(0): Not using default mode "720x400" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1152x864" (vrefresh out of range)
(II) intel(0): Not using default mode "1280x960" (hsync out of range)
(II) intel(0): Not using default mode "1280x960" (vrefresh out of range)
(II) intel(0): Not using default mode "1280x1024" (hsync out of range)
(II) intel(0): Not using default mode "1280x1024" (vrefresh out of range)
(II) intel(0): Not using default mode "1280x1024" (vrefresh out of range)
(II) intel(0): Not using default mode "1600x1200" (hsync out of range)
(II) intel(0): Not using default mode "1600x1200" (vrefresh out of range)
(II) intel(0): Not using default mode "1600x1200" (vrefresh out of range)
(II) intel(0): Not using default mode "1600x1200" (vrefresh out of range)
(II) intel(0): Not using default mode "1600x1200" (vrefresh out of range)
(II) intel(0): Not using default mode "1792x1344" (hsync out of range)
(II) intel(0): Not using default mode "1792x1344" (vrefresh out of range)
(II) intel(0): Not using default mode "1856x1392" (hsync out of range)
(II) intel(0): Not using default mode "1856x1392" (vrefresh out of range)
(II) intel(0): Not using default mode "1920x1440" (hsync out of range)
(II) intel(0): Not using default mode "1920x1440" (vrefresh out of range)
(II) intel(0): Not using default mode "832x624" (vrefresh out of range)
(II) intel(0): Not using default mode "1400x1050" (hsync out of range)
(II) intel(0): Not using default mode "1400x1050" (vrefresh out of range)
(II) intel(0): Not using default mode "1920x1440" (vrefresh out of range)
(II) intel(0): Not using default mode "2048x1536" (hsync out of range)
(II) intel(0): Not using default mode "2048x1536" (vrefresh out of range)
(II) intel(0): Not using default mode "2048x1536" (vrefresh out of range)
(II) intel(0): Printing probed modes for output Unknown-1
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): Output VGA disconnected
(II) intel(0): Output Unknown-1 connected
(II) intel(0): Using fuzzy aspect match for initial modes
(II) intel(0): Output Unknown-1 using initial mode 1024x768
(II) intel(0): detected 256 kB GTT.
(II) intel(0): detected 7932 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Intel XvMC decoder disabled
(==) intel(0): Will not try to enable page flipping
(==) intel(0): Triple buffering disabled
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"

(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "exa"
(II) LoadModule: "exa"

(II) Loading /usr/lib/xorg/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
compiled for 1.5.3, module version = 2.4.0
ABI class: X.Org Video Driver, version 4.1
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) intel(0): Comparing regs from server start up to After PreInit
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] -1 0 0xffffffff - 0xffffffff (0x1) MX[b]
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprD)
[5] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprD)
[6] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprD)
[7] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[8] -1 0 0x00000000 - 0x00000000 (0x1) IX[b]
[9] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[10] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) intel(0): Kernel reported 110080 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 440316 kB available
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) intel(0): [drm] Using the DRM lock SAREA also for drawables.
(II) intel(0): [drm] framebuffer mapped by ddx driver
(II) intel(0): [drm] added 1 reserved context for kernel
(II) intel(0): X context handle = 0x1
(II) intel(0): [drm] installed DRM signal handler
(**) intel(0): Framebuffer compression disabled
(**) intel(0): Tiling enabled
(==) intel(0): VideoRam: 262144 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(II) intel(0): Tiled allocation successful.
(II) intel(0): [drm] Registers = 0x2fbe1000
(II) intel(0): [dri] visual configs initialized
(II) intel(0): Page Flipping disabled
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) EXA(0): Offscreen pixmap area of 12582912 bytes
(II) EXA(0): Driver registered support for the following operations:
(II) Solid
(II) Copy
(II) Composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): [DRI] installation complete
(II) intel(0): Current clock rate multiplier: 2
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x0f3f5000 (pgoffset 62453)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x00009fff: HW cursors (40 kB, 0x000000001f800000 physical
)
(II) intel(0): 0x0000a000-0x0000afff: overlay registers (4 kB, 0x000000001f80a000 physical
)
(II) intel(0): 0x007bf000: end of stolen memory
(II) intel(0): 0x007bf000-0x0f3f4fff: DRI memory manager (241880 kB)
(II) intel(0): 0x0f3f5000-0x0fff4fff: exa offscreen (12288 kB)
(II) intel(0): 0x10000000: end of aperture
(II) intel(0): BO memory allocation layout:
(II) intel(0): 0x007bf000: start of memory manager
(II) intel(0): 0x00800000-0x00bfffff: depth buffer (4096 kB) X tiled
(II) intel(0): 0x00c00000-0x00ffffff: back buffer (4096 kB) X tiled
(II) intel(0): 0x01000000-0x013fffff: front buffer (4096 kB) X tiled
(II) intel(0): 0x007df000-0x007e6fff: logical 3D context (32 kB)
(II) intel(0): 0x0f3f5000: end of memory manager
(WW) intel(0): ESR is 0x00000011, page table error, instruction error
(WW) intel(0): PGTBL_ER is 0x00000002, host pte data
(WW) intel(0): PRB0_CTL (0x0001f001) indicates ring buffer enabled
(WW) intel(0): Existing errors found in hardware state.
(II) intel(0): Output configuration:
(II) intel(0): Pipe A is on
(II) intel(0): Display plane A is now enabled and connected to pipe A.
(II) intel(0): Pipe B is off
(II) intel(0): Display plane B is now disabled and connected to pipe A.
(II) intel(0): Output VGA is connected to pipe none
(II) intel(0): Output Unknown-1 is connected to pipe A
(II) intel(0): [drm] mapped front buffer at 0xd1000000, handle = 0x2a201000
(II) intel(0): [drm] mapped back buffer at 0xd0c00000, handle = 0x2a181000
(II) intel(0): [drm] mapped depth buffer at 0xd0800000, handle = 0x2a101000
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): DPMS enabled
(II) intel(0): Set up textured video
(II) intel(0): Set up overlay video
(II) intel(0): direct rendering: Enabled
(--) RandR disabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 13, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 13, (OK)
drmOpenByBusid: drmOpenMinor returns 13
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: enabled GLX_texture_from_pixmap with driver support
(II) AIGLX: Loaded and initialized /usr/lib/dri/i915_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) intel(0): Setting screen physical size to 270 x 203
(II) config/hal: Adding input device Power Button (FF)
(II) LoadModule: "evdev"

(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 2.0.7
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(**) Power Button (FF): always reports core events
(**) Power Button (FF): Device: "/dev/input/event0"
(II) Power Button (FF): Found keys
(II) Power Button (FF): Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button (FF)" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Power Button (FF): xkb_rules: "evdev"
(**) Option "xkb_model" "pc105+inet"
(**) Power Button (FF): xkb_model: "pc105+inet"
(**) Option "xkb_layout" "us"
(**) Power Button (FF): xkb_layout: "us"
(II) config/hal: Adding input device Power Button (CM)
(**) Power Button (CM): always reports core events
(**) Power Button (CM): Device: "/dev/input/event1"
(II) Power Button (CM): Found keys
(II) Power Button (CM): Configuring as keyboard
(II) XINPUT: Adding extended input device "Power Button (CM)" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Power Button (CM): xkb_rules: "evdev"
(**) Option "xkb_model" "pc105+inet"
(**) Power Button (CM): xkb_model: "pc105+inet"
(**) Option "xkb_layout" "us"
(**) Power Button (CM): xkb_layout: "us"
(II) config/hal: Adding input device HID 046a:0001
(**) HID 046a:0001: always reports core events
(**) HID 046a:0001: Device: "/dev/input/event4"
(II) HID 046a:0001: Found keys
(II) HID 046a:0001: Configuring as keyboard
(II) XINPUT: Adding extended input device "HID 046a:0001" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) HID 046a:0001: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105+inet"
(**) HID 046a:0001: xkb_model: "pc105+inet"
(**) Option "xkb_layout" "us"
(**) HID 046a:0001: xkb_layout: "us"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event2"
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Found mouse buttons
(II) Macintosh mouse button emulation: Configuring as mouse
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(II) config/hal: Adding input device Logitech USB-PS/2 Optical Mouse
(**) Logitech USB-PS/2 Optical Mouse: always reports core events
(**) Logitech USB-PS/2 Optical Mouse: Device: "/dev/input/event3"
(II) Logitech USB-PS/2 Optical Mouse: Found x and y relative axes
(II) Logitech USB-PS/2 Optical Mouse: Found mouse buttons
(II) Logitech USB-PS/2 Optical Mouse: Configuring as mouse
(II) XINPUT: Adding extended input device "Logitech USB-PS/2 Optical Mouse" (type: MOUSE)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output Unknown-1
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): Not using default mode "640x350" (vrefresh out of range)
(II) intel(0): Not using default mode "640x400" (vrefresh out of range)
(II) intel(0): Not using default mode "720x400" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1152x864" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "832x624" (vrefresh out of range)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Printing probed modes for output Unknown-1
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output Unknown-1
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): Not using default mode "640x350" (vrefresh out of range)
(II) intel(0): Not using default mode "640x400" (vrefresh out of range)
(II) intel(0): Not using default mode "720x400" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1152x864" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "832x624" (vrefresh out of range)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Printing probed modes for output Unknown-1
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output Unknown-1
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): Not using default mode "640x350" (vrefresh out of range)
(II) intel(0): Not using default mode "640x400" (vrefresh out of range)
(II) intel(0): Not using default mode "720x400" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1152x864" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "832x624" (vrefresh out of range)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Printing probed modes for output Unknown-1
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): EDID for output VGA
(II) intel(0): EDID for output Unknown-1
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "CRTDDC_A:ddc2" registered at address 0xA0.
(II) intel(0): I2C device "CRTDDC_A:ddc2" removed.
(II) intel(0): I2C device "CRTDDC_A:E-EDID segment register" removed.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): Not using default mode "640x350" (vrefresh out of range)
(II) intel(0): Not using default mode "640x400" (vrefresh out of range)
(II) intel(0): Not using default mode "720x400" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "640x480" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "800x600" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1024x768" (vrefresh out of range)
(II) intel(0): Not using default mode "1152x864" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x960" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1280x1024" (width too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1600x1200" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1792x1344" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1856x1392" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "832x624" (vrefresh out of range)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1400x1050" (height too large for virtual size)
(II) intel(0): Not using default mode "1920x1440" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Not using default mode "2048x1536" (height too large for virtual size)
(II) intel(0): Printing probed modes for output Unknown-1
(II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
(II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
(II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 05:14 PM
Adam Jackson
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, 2008-11-24 at 17:57 +0100, Jos Vos wrote:
> On Mon, Nov 24, 2008 at 11:50:24AM -0500, Adam Jackson wrote:
>
> > Typically the VBT signature doesn't mean much. But yes, full log would
> > be interesting.
>
> I tried with 32-bit: still no graphics.
>
> Attached:
> - Xorg.0.log.vesa (no xorg.conf or xorg.conf specifying "vesa") and
> - Xorg.0.log.intel (with xorg.conf specifying "intel").

Very strange. What kind of display is it? Are you using an SDVO card
(pseudo-PCIE looking thing with a tiny chip on one side and a DVI or
whatever connector on the other)?

- ajax
--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 06:17 PM
Jos Vos
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, Nov 24, 2008 at 01:14:56PM -0500, Adam Jackson wrote:

> Very strange. What kind of display is it? Are you using an SDVO card
> (pseudo-PCIE looking thing with a tiny chip on one side and a DVI or
> whatever connector on the other)?

It's a completely integrated system with a 15" LCD display (with serial
Elo touchscreen option), the IBM SurePOS 565:

http://www-03.ibm.com/products/retail/products/pos/500/specs_eu.html
http://www-03.ibm.com/products/retail/products/pos/500/prodview.html

AFAIK the graphic chip is on the mainboard, but I'm not sure.

On RHEL4 (currently used in production) and RHEL5 (tested a few times)
I had to do some small tweaking to make it all work, like specifying
"nofb" as kernel option, turning off acceleration ("NoAccel" "yes"),
turning of acpi (mainly because of disk/USB problems), etc.

I didn't try all combinations of tweaks yet, but AFAIK I never had a
full black screen in RHELx, only other strange effects (like a display
that 30% shifted vertically).

--
-- Jos Vos <jos@xos.nl>
-- X/OS Experts in Open Systems BV | Phone: +31 20 6938364
-- Amsterdam, The Netherlands | Fax: +31 20 6948204

--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 07:40 PM
Adam Jackson
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, 2008-11-24 at 20:17 +0100, Jos Vos wrote:
> On Mon, Nov 24, 2008 at 01:14:56PM -0500, Adam Jackson wrote:
>
> > Very strange. What kind of display is it? Are you using an SDVO card
> > (pseudo-PCIE looking thing with a tiny chip on one side and a DVI or
> > whatever connector on the other)?
>
> It's a completely integrated system with a 15" LCD display (with serial
> Elo touchscreen option), the IBM SurePOS 565:
>
> http://www-03.ibm.com/products/retail/products/pos/500/specs_eu.html
> http://www-03.ibm.com/products/retail/products/pos/500/prodview.html
>
> AFAIK the graphic chip is on the mainboard, but I'm not sure.
>
> On RHEL4 (currently used in production) and RHEL5 (tested a few times)
> I had to do some small tweaking to make it all work, like specifying
> "nofb" as kernel option, turning off acceleration ("NoAccel" "yes"),
> turning of acpi (mainly because of disk/USB problems), etc.
>
> I didn't try all combinations of tweaks yet, but AFAIK I never had a
> full black screen in RHELx, only other strange effects (like a display
> that 30% shifted vertically).

In RHEL5 you'd still be using the old BIOS-based i810 driver (assuming
you installed with 5.1 or older), which might work through blind luck.

The current theory is that it's trying to do LVDS over SDVO, which is a
bit insane since it has LVDS on the board already, and that's a path
that the driver currently doesn't support. If we could get copies of
the video BIOS (and some testing time, if you're up for it) we can
probably work with intel to get it going. Probably best to do that in a
bug, either in fedora or freedesktop bugzilla.

- ajax
--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-24-2008, 09:45 PM
Jos Vos
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, Nov 24, 2008 at 03:40:47PM -0500, Adam Jackson wrote:

> In RHEL5 you'd still be using the old BIOS-based i810 driver (assuming
> you installed with 5.1 or older), which might work through blind luck.

Yes, in my RHEL5 notes I wrote that I should use the "i810" driver (maybe
there the "intel" driver was chosen by default).

I see that it's still there (/usr/lib/xorg/modules/drivers/i810_drv.so),
but it does not seem to work (I only tried it remotely, I'm not in the
office anymore):

(II) Loading /usr/lib/xorg/modules/drivers//i810_drv.so
(II) Module i810: vendor="X.Org Foundation"
compiled for 1.5.2, module version = 2.5.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 4.1
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
965GM, 965GME/GLE, G33, Q35, Q33,
Mobile Intel® GM45 Express Chipset,
Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
(II) Primary Device is: PCI 00@00:02:0
(EE) No devices detected.

> The current theory is that it's trying to do LVDS over SDVO, which is a
> bit insane since it has LVDS on the board already, and that's a path
> that the driver currently doesn't support. If we could get copies of
> the video BIOS (and some testing time, if you're up for it) we can
> probably work with intel to get it going. Probably best to do that in a
> bug, either in fedora or freedesktop bugzilla.

I see that I can't file bugs against F10 yet (I'm using the final F10
media already ;-)). Will try again tomorrow and post the bug # here,
as a reference.

--
-- Jos Vos <jos@xos.nl>
-- X/OS Experts in Open Systems BV | Phone: +31 20 6938364
-- Amsterdam, The Netherlands | Fax: +31 20 6948204

--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 
Old 11-25-2008, 08:57 PM
Adam Jackson
 
Default No X on F9/F10 with Intel 82915G/GV/910GL

On Mon, 2008-11-24 at 23:45 +0100, Jos Vos wrote:
> On Mon, Nov 24, 2008 at 03:40:47PM -0500, Adam Jackson wrote:
>
> > In RHEL5 you'd still be using the old BIOS-based i810 driver (assuming
> > you installed with 5.1 or older), which might work through blind luck.
>
> Yes, in my RHEL5 notes I wrote that I should use the "i810" driver (maybe
> there the "intel" driver was chosen by default).
>
> I see that it's still there (/usr/lib/xorg/modules/drivers/i810_drv.so),
> but it does not seem to work (I only tried it remotely, I'm not in the
> office anymore):

It's not really still there, it's just a symlink, the intel driver
responds to both names so people with i810 in their config file get
working X across upgrades. We should probably just munge the config
file and drop the symlink at this point.

- ajax

--
fedora-devel-list mailing list
fedora-devel-list@redhat.com
https://www.redhat.com/mailman/listinfo/fedora-devel-list
 

Thread Tools




All times are GMT. The time now is 03:12 AM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright ©2007 - 2008, www.linux-archive.org