Linux Archive

Linux Archive (http://www.linux-archive.org/)
-   Debian User (http://www.linux-archive.org/debian-user/)
-   -   Debian on a Macbook (Leopard): Xorg installation leads to blank screen on reboot (http://www.linux-archive.org/debian-user/510217-debian-macbook-leopard-xorg-installation-leads-blank-screen-reboot.html)

Arvind 04-05-2011 12:12 PM

Debian on a Macbook (Leopard): Xorg installation leads to blank screen on reboot
 
Hello,

I am trying to install debian squeeze amd64 on my girlfriend's
macbook. It already has OS X installed, so this is a dual boot system.
Following are the hardware specifications:

System: Apple macbook, Intel core 2 duo - T8100 @ 2.10GHz, 1 GB RAM

As explained on the debian wiki:
http://wiki.debian.org/MacBook/DebianInstallTutorial
i installed OS X initially, installed rEFIt, and then did an absolute
minimal install of debian squeeze amd64 on the rest of the hard disk.

For what it is worth, my filesystem structure has /boot and swap
on separate partitions, and / /usr /usr/local /var /tmp and /home on
lvm. I have used ext4 filesystem on all the partitions.

At the stage of minimal installation, rEFIt menu provided options to
boot into both OS X and debian gnu/linux. When i selected gnu/linux,
it booted as expected, and provided a console prompt. I could log in
and work. At this stage, i installed some other necessary softwares
such as openssh, gnu screen etc.

Next, i did:
aptitude install xorg icewm
It installed everything alright. I created a .xinitrc file with the
lines:

----------------------------------------------------------------------
#!/bin/bash
exec icewm-session
----------------------------------------------------------------------

and issued the command 'startx' (as user). X started, and i could get
the default icewm setup.

So far, so good. However, when i rebooted the machine, and selected
gnu/linux at the rEFIt prompt, it showed the grub selection menu,
selected the default kernel, showed a few more lines scrolling down
and then the screen just went blank. I could not make out if it was
doing anything at all.

So i took the machine to my workplace, put it on a network and found
that i could ssh to the machine. So i presume it is a video driver
problem. Here is the relevant output of 'lspci -v'

----------------------------------------------------------------------
00:02.0 VGA compatible controller: Intel Corporation Mobile
GM965/GL960 Integrated Graphics Controller (rev 03) (prog-if 00 [VGA
controller])
Subsystem: Apple Computer Inc. Device 00a1
Flags: bus master, fast devsel, latency 0, IRQ 28
Memory at 50100000 (64-bit, non-prefetchable) [size=1M]
Memory at 40000000 (64-bit, prefetchable) [size=256M]
I/O ports at 6110 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [d0] Power Management version 3
Kernel driver in use: i915

00:02.1 Display controller: Intel Corporation Mobile GM965/GL960
Integrated Graphics Controller (rev 03)
Subsystem: Apple Computer Inc. Device 00a1
Flags: bus master, fast devsel, latency 0
Memory at 50200000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 3
----------------------------------------------------------------------

Do i need to create an xorg.conf specifying some driver, modules etc.?
Or the problem is elsewhere? Below, i have also attached the output of
dmesg, where few other lines also appear problematic.

Any help appreciated. This is my first brush with an apple macbook,
but i am not new to debian gnu/linux.

Thanks,
arvind

--
Quidquid latine dictum sit, altum sonatur.


Output of dmesg:
----------------------------------------------------------------------
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-amd64 (Debian 2.6.32-31) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Mar 7 21:35:22 UTC 2011
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=/dev/mapper/vg-root ro quiet
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003dd31000 (usable)
[ 0.000000] BIOS-e820: 000000003dd31000 - 000000003df32000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003df32000 - 000000003dfe4000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003dfe4000 - 000000003dfe6000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003dfe6000 - 000000003eec3000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003eec3000 - 000000003eec5000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003eec5000 - 000000003eec8000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003eec8000 - 000000003eecb000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003eecb000 - 000000003eecc000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003eecc000 - 000000003eedf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003eedf000 - 000000003eef9000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003eef9000 - 000000003eeff000 (reserved)
[ 0.000000] BIOS-e820: 000000003eeff000 - 000000003ef00000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ef00000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.4 present.
[ 0.000000] last_pfn = 0x3dd31 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFE00000 mask FFFE00000 write-protect
[ 0.000000] 1 base 000000000 mask FC0000000 write-back
[ 0.000000] 2 base 03F000000 mask FFF000000 uncachable
[ 0.000000] 3 base 03EF00000 mask FFFF00000 uncachable
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 20000000
[ 0.000000] init_memory_mapping: 0000000000000000-000000003dd31000
[ 0.000000] 0000000000 - 003dc00000 page 2M
[ 0.000000] 003dc00000 - 003dd31000 page 4k
[ 0.000000] kernel direct mapping tables up to 3dd31000 @ 8000-b000
[ 0.000000] RAMDISK: 2e29f000 - 2e624506
[ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 APPLE )
[ 0.000000] ACPI: XSDT 000000003eeee1c0 00084 (v01 APPLE Apple00 000000C1 01000013)
[ 0.000000] ACPI: FACP 000000003eeec000 000F4 (v03 APPLE Apple00 000000C1 Loki 0000005F)
[ 0.000000] ACPI: DSDT 000000003eee1000 045C6 (v01 APPLE MacBook 00040001 INTL 20061109)
[ 0.000000] ACPI: FACS 000000003eecc000 00040
[ 0.000000] ACPI: HPET 000000003eeeb000 00038 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: APIC 000000003eeea000 00068 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: MCFG 000000003eee9000 0003C (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: ASF! 000000003eee8000 000A5 (v32 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: SBST 000000003eee7000 00030 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: ECDT 000000003eee6000 00053 (v01 APPLE Apple00 00000001 Loki 0000005F)
[ 0.000000] ACPI: SSDT 000000003eec7000 004DC (v01 APPLE CpuPm 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 000000003eec6000 0025F (v01 APPLE Cpu0Tst 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 000000003eec5000 000A6 (v01 APPLE Cpu1Tst 00003000 INTL 20061109)
[ 0.000000] ACPI: SSDT 000000003eee0000 00544 (v01 SataRe SataPri 00001000 INTL 20061109)
[ 0.000000] ACPI: SSDT 000000003eedf000 00477 (v01 SataRe SataSec 00001000 INTL 20061109)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000003dd31000
[ 0.000000] Bootmem setup node 0 0000000000000000-000000003dd31000
[ 0.000000] NODE_DATA [0000000000009000 - 0000000000010fff]
[ 0.000000] bootmap [0000000000011000 - 0000000000018ba7] pages 8
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 003dd31000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000]
[ 0.000000] #2 [0001000000 - 000168a454] TEXT DATA BSS ==> [0001000000 - 000168a454]
[ 0.000000] #3 [002e29f000 - 002e624506] RAMDISK ==> [002e29f000 - 002e624506]
[ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
[ 0.000000] #5 [000168b000 - 000168b22d] BRK ==> [000168b000 - 000168b22d]
[ 0.000000] #6 [0000008000 - 0000009000] PGTABLE ==> [0000008000 - 0000009000]
[ 0.000000] [ffffea0000000000-ffffea0000dfffff] PMD -> [ffff880001c00000-ffff8800029fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] DMA32 0x00001000 -> 0x00100000
[ 0.000000] Normal 0x00100000 -> 0x00100000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003dd31
[ 0.000000] On node 0 totalpages: 253136
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 100 pages reserved
[ 0.000000] DMA zone: 3843 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 3407 pages used for memmap
[ 0.000000] DMA32 zone: 245730 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:b0000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 30 pages/cpu @ffff880001800000 s90328 r8192 d24360 u1048576
[ 0.000000] pcpu-alloc: s90328 r8192 d24360 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 249573
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=/dev/mapper/vg-root ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 987328k/1012932k available (3080k kernel code, 388k absent, 25216k reserved, 1891k data, 592k init)
[ 0.000000] SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:4352 nr_irqs:424
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2094.806 MHz processor.
[ 0.004006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4189.61 BogoMIPS (lpj=8379224)
[ 0.004025] Security Framework initialized
[ 0.004031] SELinux: Disabled at boot.
[ 0.004122] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.004711] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.008277] Mount-cache hash table entries: 256
[ 0.008415] Initializing cgroup subsys ns
[ 0.008419] Initializing cgroup subsys cpuacct
[ 0.008422] Initializing cgroup subsys devices
[ 0.008424] Initializing cgroup subsys freezer
[ 0.008426] Initializing cgroup subsys net_cls
[ 0.008452] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008454] CPU: L2 cache: 3072K
[ 0.008458] CPU 0/0x0 -> Node 0
[ 0.008460] CPU: Physical Processor ID: 0
[ 0.008461] CPU: Processor Core ID: 0
[ 0.008464] mce: CPU supports 6 MCE banks
[ 0.008472] CPU0: Thermal monitoring enabled (TM2)
[ 0.008475] using mwait in idle threads.
[ 0.008477] Performance Events: Core2 events, Intel PMU driver.
[ 0.008482] ... version: 2
[ 0.008483] ... bit width: 40
[ 0.008485] ... generic registers: 2
[ 0.008486] ... value mask: 000000ffffffffff
[ 0.008488] ... max period: 000000007fffffff
[ 0.008489] ... fixed-purpose events: 3
[ 0.008491] ... event mask: 0000000700000003
[ 0.009552] ACPI: Core revision 20090903
[ 0.015570] Setting APIC routing to flat
[ 0.015922] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.055615] CPU0: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping 06
[ 0.056001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.008000] CPU: L2 cache: 3072K
[ 0.008000] CPU 1/0x1 -> Node 0
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU1: Thermal monitoring enabled (TM2)
[ 0.140042] CPU1: Intel(R) Core(TM)2 Duo CPU T8100 @ 2.10GHz stepping 06
[ 0.140050] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.144020] Brought up 2 CPUs
[ 0.144023] Total of 2 processors activated (8379.06 BogoMIPS).
[ 0.144651] CPU0 attaching sched-domain:
[ 0.144655] domain 0: span 0-1 level MC
[ 0.144657] groups: 0 1
[ 0.144662] CPU1 attaching sched-domain:
[ 0.144664] domain 0: span 0-1 level MC
[ 0.144666] groups: 1 0
[ 0.144724] devtmpfs: initialized
[ 0.148014] regulator: core version 0.5
[ 0.148060] NET: Registered protocol family 16
[ 0.148155] ACPI: bus type pci registered
[ 0.148220] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255
[ 0.148223] PCI: MCFG area at f0000000 reserved in E820
[ 0.148225] PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63
[ 0.150642] PCI: Using MMCONFIG at f0000000 - f3ffffff
[ 0.150644] PCI: Using configuration type 1 for base access
[ 0.150935] bio: create slab <bio-0> at 0
[ 0.150935] ACPI: EC: EC description table is found, configuring boot EC
[ 0.153362] ACPI: BIOS _OSI(Linux) query ignored
[ 0.153635] ACPI: Interpreter enabled
[ 0.153637] ACPI: (supports S0 S3 S4 S5)
[ 0.153656] ACPI: Using IOAPIC for interrupt routing
[ 0.160234] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.160515] ACPI: No dock devices found.
[ 0.164184] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.164267] pci 0000:00:02.0: reg 10 64bit mmio: [0x50100000-0x501fffff]
[ 0.164274] pci 0000:00:02.0: reg 18 64bit mmio pref: [0x40000000-0x4fffffff]
[ 0.164278] pci 0000:00:02.0: reg 20 io port: [0x6110-0x6117]
[ 0.164313] pci 0000:00:02.1: reg 10 64bit mmio: [0x50200000-0x502fffff]
[ 0.164418] pci 0000:00:1a.0: reg 20 io port: [0x60c0-0x60df]
[ 0.164482] pci 0000:00:1a.1: reg 20 io port: [0x60a0-0x60bf]
[ 0.164554] pci 0000:00:1a.7: reg 10 32bit mmio: [0x50704c00-0x50704fff]
[ 0.164615] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.164621] pci 0000:00:1a.7: PME# disabled
[ 0.164674] pci 0000:00:1b.0: reg 10 64bit mmio: [0x50700000-0x50703fff]
[ 0.164733] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.164738] pci 0000:00:1b.0: PME# disabled
[ 0.164829] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.164834] pci 0000:00:1c.0: PME# disabled
[ 0.164932] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.164937] pci 0000:00:1c.4: PME# disabled
[ 0.165031] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.165035] pci 0000:00:1c.5: PME# disabled
[ 0.165097] pci 0000:00:1d.0: reg 20 io port: [0x6080-0x609f]
[ 0.165161] pci 0000:00:1d.1: reg 20 io port: [0x6060-0x607f]
[ 0.165225] pci 0000:00:1d.2: reg 20 io port: [0x6040-0x605f]
[ 0.165296] pci 0000:00:1d.7: reg 10 32bit mmio: [0x50704800-0x50704bff]
[ 0.165358] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.165363] pci 0000:00:1d.7: PME# disabled
[ 0.165534] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 0.165538] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
[ 0.165543] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0680 (mask 000f)
[ 0.165547] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 1640 (mask 000f)
[ 0.165553] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 0300 (mask 001f)
[ 0.165604] pci 0000:00:1f.1: reg 10 io port: [0x6108-0x610f]
[ 0.165612] pci 0000:00:1f.1: reg 14 io port: [0x6124-0x6127]
[ 0.165620] pci 0000:00:1f.1: reg 18 io port: [0x6100-0x6107]
[ 0.165627] pci 0000:00:1f.1: reg 1c io port: [0x6120-0x6123]
[ 0.165635] pci 0000:00:1f.1: reg 20 io port: [0x60e0-0x60ef]
[ 0.165691] pci 0000:00:1f.2: reg 10 io port: [0x60f8-0x60ff]
[ 0.165699] pci 0000:00:1f.2: reg 14 io port: [0x611c-0x611f]
[ 0.165707] pci 0000:00:1f.2: reg 18 io port: [0x60f0-0x60f7]
[ 0.165714] pci 0000:00:1f.2: reg 1c io port: [0x6118-0x611b]
[ 0.165722] pci 0000:00:1f.2: reg 20 io port: [0x6020-0x602f]
[ 0.165729] pci 0000:00:1f.2: reg 24 io port: [0x4000-0x400f]
[ 0.165759] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.165763] pci 0000:00:1f.2: PME# disabled
[ 0.165790] pci 0000:00:1f.3: reg 10 32bit mmio: [0x50705000-0x507050ff]
[ 0.165814] pci 0000:00:1f.3: reg 20 io port: [0xefa0-0xefbf]
[ 0.165903] pci 0000:00:1c.0: bridge 32bit mmio: [0x50600000-0x506fffff]
[ 0.165988] pci 0000:02:00.0: reg 10 64bit mmio: [0x50500000-0x50503fff]
[ 0.166006] pci 0000:02:00.0: reg 18 64bit mmio pref: [0x50000000-0x500fffff]
[ 0.166085] pci 0000:02:00.0: supports D1 D2
[ 0.166087] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.166092] pci 0000:02:00.0: PME# disabled
[ 0.172128] pci 0000:00:1c.4: bridge 32bit mmio: [0x50500000-0x505fffff]
[ 0.172136] pci 0000:00:1c.4: bridge 64bit mmio pref: [0x50000000-0x500fffff]
[ 0.172490] pci 0000:03:00.0: reg 10 64bit mmio: [0x50400000-0x50403fff]
[ 0.172539] pci 0000:03:00.0: reg 18 io port: [0x5000-0x50ff]
[ 0.172712] pci 0000:03:00.0: reg 30 32bit mmio pref: [0xfffe0000-0xffffffff]
[ 0.172972] pci 0000:03:00.0: supports D1 D2
[ 0.172974] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.173000] pci 0000:03:00.0: PME# disabled
[ 0.173800] pci 0000:00:1c.5: bridge io port: [0x5000-0x5fff]
[ 0.173805] pci 0000:00:1c.5: bridge 32bit mmio: [0x50400000-0x504fffff]
[ 0.173862] pci 0000:04:03.0: reg 10 32bit mmio: [0x50300000-0x50300fff]
[ 0.173924] pci 0000:04:03.0: supports D1 D2
[ 0.173925] pci 0000:04:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.173930] pci 0000:04:03.0: PME# disabled
[ 0.173992] pci 0000:00:1e.0: transparent bridge
[ 0.174000] pci 0000:00:1e.0: bridge 32bit mmio: [0x50300000-0x503fffff]
[ 0.174034] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.174230] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP05._PRT]
[ 0.174299] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.174389] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.182852] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.182942] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15)
[ 0.183033] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 *5 6 7 10 12 14 15)
[ 0.183120] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.183211] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.183298] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *9
[ 0.183385] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.183473] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.183560] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.183573] vgaarb: loaded
[ 0.183586] PCI: Using ACPI for IRQ routing
[ 0.183586] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.183586] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.183586] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.188016] Switching to clocksource tsc
[ 0.189152] pnp: PnP ACPI init
[ 0.189163] ACPI: bus type pnp registered
[ 0.195694] pnp: PnP ACPI: found 9 devices
[ 0.195696] ACPI: ACPI bus type pnp unregistered
[ 0.195705] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.195708] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.195711] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.195713] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.195716] system 00:01: iomem range 0xf0000000-0xf3ffffff has been reserved
[ 0.195719] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.195722] system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved
[ 0.195735] system 00:05: iomem range 0xfed00000-0xfed003ff has been reserved
[ 0.195741] system 00:07: ioport range 0x680-0x69f has been reserved
[ 0.195744] system 00:07: ioport range 0x800-0x80f has been reserved
[ 0.195746] system 00:07: ioport range 0x810-0x817 has been reserved
[ 0.195749] system 00:07: ioport range 0x400-0x47f has been reserved
[ 0.195751] system 00:07: ioport range 0x500-0x53f has been reserved
[ 0.195754] system 00:07: ioport range 0x1640-0x164f has been reserved
[ 0.200442] pci 0000:03:00.0: BAR 6: no parent found for of device [0xfffe0000-0xffffffff]
[ 0.200543] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[ 0.200546] pci 0000:00:1c.0: IO window: 0x2000-0x2fff
[ 0.200552] pci 0000:00:1c.0: MEM window: 0x50600000-0x506fffff
[ 0.200558] pci 0000:00:1c.0: PREFETCH window: 0x00000050800000-0x000000509fffff
[ 0.200565] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:02
[ 0.200569] pci 0000:00:1c.4: IO window: 0x3000-0x3fff
[ 0.200575] pci 0000:00:1c.4: MEM window: 0x50500000-0x505fffff
[ 0.200580] pci 0000:00:1c.4: PREFETCH window: 0x00000050000000-0x000000500fffff
[ 0.200588] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:03
[ 0.200591] pci 0000:00:1c.5: IO window: 0x5000-0x5fff
[ 0.200597] pci 0000:00:1c.5: MEM window: 0x50400000-0x504fffff
[ 0.200602] pci 0000:00:1c.5: PREFETCH window: 0x50a00000-0x50bfffff
[ 0.200610] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[ 0.200612] pci 0000:00:1e.0: IO window: disabled
[ 0.200618] pci 0000:00:1e.0: MEM window: 0x50300000-0x503fffff
[ 0.200622] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.200636] pci 0000:00:1c.0: enabling device (0000 -> 0003)
[ 0.200641] alloc irq_desc for 16 on node -1
[ 0.200643] alloc kstat_irqs on node -1
[ 0.200649] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.200656] pci 0000:00:1c.0: setting latency timer to 64
[ 0.200666] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.200671] pci 0000:00:1c.4: setting latency timer to 64
[ 0.200680] alloc irq_desc for 17 on node -1
[ 0.200682] alloc kstat_irqs on node -1
[ 0.200685] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.200690] pci 0000:00:1c.5: setting latency timer to 64
[ 0.200745] pci 0000:00:1e.0: power state changed by ACPI to D0
[ 0.200791] pci 0000:00:1e.0: power state changed by ACPI to D0
[ 0.200798] pci 0000:00:1e.0: setting latency timer to 64
[ 0.200802] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.200805] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
[ 0.200807] pci_bus 0000:01: resource 0 io: [0x2000-0x2fff]
[ 0.200809] pci_bus 0000:01: resource 1 mem: [0x50600000-0x506fffff]
[ 0.200812] pci_bus 0000:01: resource 2 pref mem [0x50800000-0x509fffff]
[ 0.200814] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
[ 0.200816] pci_bus 0000:02: resource 1 mem: [0x50500000-0x505fffff]
[ 0.200818] pci_bus 0000:02: resource 2 pref mem [0x50000000-0x500fffff]
[ 0.200821] pci_bus 0000:03: resource 0 io: [0x5000-0x5fff]
[ 0.200823] pci_bus 0000:03: resource 1 mem: [0x50400000-0x504fffff]
[ 0.200825] pci_bus 0000:03: resource 2 pref mem [0x50a00000-0x50bfffff]
[ 0.200828] pci_bus 0000:04: resource 1 mem: [0x50300000-0x503fffff]
[ 0.200830] pci_bus 0000:04: resource 3 io: [0x00-0xffff]
[ 0.200832] pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffffffffffff]
[ 0.200858] NET: Registered protocol family 2
[ 0.200948] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.201394] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[ 0.202256] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.202700] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.202702] TCP reno registered
[ 0.202818] NET: Registered protocol family 1
[ 0.202840] pci 0000:00:02.0: Boot video device
[ 0.203030] Unpacking initramfs...
[ 0.277531] Freeing initrd memory: 3605k freed
[ 0.279576] audit: initializing netlink socket (disabled)
[ 0.279593] type=2000 audit(1302005088.275:1): initialized
[ 0.282501] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.283818] VFS: Disk quotas dquot_6.5.2
[ 0.283870] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.283965] msgmni has been set to 1935
[ 0.284150] alg: No test for stdrng (krng)
[ 0.284206] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.284209] io scheduler noop registered
[ 0.284211] io scheduler anticipatory registered
[ 0.284213] io scheduler deadline registered
[ 0.284245] io scheduler cfq registered (default)
[ 0.284383] alloc irq_desc for 24 on node -1
[ 0.284385] alloc kstat_irqs on node -1
[ 0.284400] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.284411] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.284561] alloc irq_desc for 25 on node -1
[ 0.284563] alloc kstat_irqs on node -1
[ 0.284571] pcieport 0000:00:1c.4: irq 25 for MSI/MSI-X
[ 0.284582] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.284729] alloc irq_desc for 26 on node -1
[ 0.284731] alloc kstat_irqs on node -1
[ 0.284740] pcieport 0000:00:1c.5: irq 26 for MSI/MSI-X
[ 0.284750] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.284895] efifb: dmi detected MacBook4,1 - framebuffer at 0000000080000000 (1280x800, stride 8192)
[ 0.286265] Linux agpgart interface v0.103
[ 0.286279] agpgart-intel 0000:00:00.0: Intel 965GM Chipset
[ 0.287258] agpgart-intel 0000:00:00.0: detected 15868K stolen memory
[ 0.291998] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0x40000000
[ 0.292051] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.292391] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 0.292453] PNP: No PS/2 controller found. Probing ports directly.
[ 0.293303] i8042.c: No controller found.
[ 0.293414] mice: PS/2 mouse device common for all mice
[ 0.293457] rtc_cmos 00:08: RTC can wake from S4
[ 0.293496] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 0.293531] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.293540] cpuidle: using governor ladder
[ 0.293542] cpuidle: using governor menu
[ 0.293546] No iBFT detected.
[ 0.293846] TCP cubic registered
[ 0.293952] NET: Registered protocol family 10
[ 0.294611] Mobile IPv6
[ 0.294614] NET: Registered protocol family 17
[ 0.294688] PM: Resume from disk failed.
[ 0.294698] registered taskstats version 1
[ 0.295323] rtc_cmos 00:08: setting system clock to 2011-04-05 12:04:48 UTC (1302005088)
[ 0.295380] Initalizing network drop monitor service
[ 0.295404] Freeing unused kernel memory: 592k freed
[ 0.295551] Write protecting the kernel read-only data: 4236k
[ 0.308540] udev[56]: starting version 164
[ 0.399780] SCSI subsystem initialized
[ 0.413428] libata version 3.00 loaded.
[ 0.415572] ata_piix 0000:00:1f.1: version 2.13
[ 0.415638] ata_piix 0000:00:1f.1: power state changed by ACPI to D0
[ 0.415670] ata_piix 0000:00:1f.1: power state changed by ACPI to D0
[ 0.415679] alloc irq_desc for 21 on node -1
[ 0.415681] alloc kstat_irqs on node -1
[ 0.415690] ata_piix 0000:00:1f.1: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[ 0.415730] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.415794] scsi0 : ata_piix
[ 0.415870] scsi1 : ata_piix
[ 0.416388] ata1: PATA max UDMA/100 cmd 0x6108 ctl 0x6124 bmdma 0x60e0 irq 21
[ 0.416391] ata2: PATA max UDMA/100 cmd 0x6100 ctl 0x6120 bmdma 0x60e8 irq 21
[ 0.416413] alloc irq_desc for 18 on node -1
[ 0.416415] alloc kstat_irqs on node -1
[ 0.416419] ata_piix 0000:00:1f.2: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 0.416425] ata_piix 0000:00:1f.2: MAP [ P0 -- -- -- ]
[ 0.416468] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 0.416630] scsi2 : ata_piix
[ 0.416682] scsi3 : ata_piix
[ 0.417472] ata3: SATA max UDMA/133 cmd 0x60f8 ctl 0x611c bmdma 0x6020 irq 18
[ 0.417474] ata4: SATA max UDMA/133 cmd 0x60f0 ctl 0x6118 bmdma 0x6028 irq 18
[ 0.584200] ata1.00: ATAPI: MATSHITACD-RW CW-8221, GA0K, max UDMA/33
[ 0.588172] ata3.00: ATA-8: FUJITSU MHY2120BH, 0081000D, max UDMA/100
[ 0.588175] ata3.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 0.596204] ata1.00: configured for UDMA/33
[ 0.604190] ata3.00: configured for UDMA/100
[ 0.625600] scsi 0:0:0:0: CD-ROM MATSHITA CD-RW CW-8221 GA0K PQ: 0 ANSI: 5
[ 0.625772] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHY2120B 0081 PQ: 0 ANSI: 5
[ 0.630680] sd 2:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
[ 0.630796] sd 2:0:0:0: [sda] Write Protect is off
[ 0.630799] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.630830] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.630973] sda: sda1 sda2 sda3 sda4 sda5
[ 0.633076] sd 2:0:0:0: [sda] Attached SCSI disk
[ 0.988708] device-mapper: uevent: version 1.0.3
[ 0.988838] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 1.100551] PM: Starting manual resume from disk
[ 1.100555] PM: Resume from partition 8:4
[ 1.100556] PM: Checking hibernation image.
[ 1.100760] PM: Error -22 checking image file
[ 1.100762] PM: Resume from disk failed.
[ 1.138662] EXT4-fs (dm-0): mounted filesystem with ordered data mode
[ 1.849153] udev[389]: starting version 164
[ 1.949799] ACPI: SSDT 000000003eecaa98 002FE (v01 APPLE Cpu0Ist 00003000 INTL 20061109)
[ 1.950140] ACPI: SSDT 000000003eec8c18 002AD (v01 APPLE Cpu0Cst 00003001 INTL 20061109)
[ 1.968457] Monitor-Mwait will be used to enter C-1 state
[ 1.985325] Monitor-Mwait will be used to enter C-2 state
[ 1.988502] Monitor-Mwait will be used to enter C-3 state
[ 1.988510] Marking TSC unstable due to TSC halts in idle
[ 1.988619] processor LNXCPU:00: registered as cooling_device0
[ 1.989043] ACPI: SSDT 000000003eec9f18 000C8 (v01 APPLE Cpu1Ist 00003000 INTL 20061109)
[ 1.989301] ACPI: SSDT 000000003eec8f18 00085 (v01 APPLE Cpu1Cst 00003000 INTL 20061109)
[ 1.990297] Switching to clocksource hpet
[ 1.990435] processor LNXCPU:01: registered as cooling_device1
[ 2.118298] ACPI: Battery Slot [BAT0] (battery present)
[ 2.118369] ACPI: AC Adapter [ADP1] (on-line)
[ 2.118447] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 2.118487] ACPI: Lid Switch [LID0]
[ 2.118541] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 2.118546] ACPI: Power Button [PWRB]
[ 2.118591] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 2.118594] ACPI: Sleep Button [SLPB]
[ 2.118653] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 2.118656] ACPI: Power Button [PWRF]
[ 2.130489] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 2.167371] usbcore: registered new interface driver usbfs
[ 2.167428] usbcore: registered new interface driver hub
[ 2.167483] usbcore: registered new device driver usb
[ 2.168763] mbp_nvidia_bl: MacBook 4,1 detected
[ 2.210340] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6
[ 2.210382] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.264085] alloc irq_desc for 20 on node -1
[ 2.264088] alloc kstat_irqs on node -1
[ 2.264095] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 2.264100] ACPI: I/O resource 0000:00:1f.3 [0xefa0-0xefbf] conflicts with ACPI region SMBI [0xefa0-0xefaf]
[ 2.264158] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 2.284891] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.284915] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 2.284933] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 2.284937] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 2.284957] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 2.284995] ehci_hcd 0000:00:1a.7: debug port 1
[ 2.288882] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 2.288890] ehci_hcd 0000:00:1a.7: irq 21, io mem 0x50704c00
[ 2.304019] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 2.304041] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.304043] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.304046] usb usb1: Product: EHCI Host Controller
[ 2.304048] usb usb1: Manufacturer: Linux 2.6.32-5-amd64 ehci_hcd
[ 2.304049] usb usb1: SerialNumber: 0000:00:1a.7
[ 2.304183] usb usb1: configuration #1 chosen from 1 choice
[ 2.304243] hub 1-0:1.0: USB hub found
[ 2.304251] hub 1-0:1.0: 4 ports detected
[ 2.304313] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 20 (level, low) -> IRQ 20
[ 2.304329] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 2.304332] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.304339] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 2.304373] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.308257] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 2.308274] ehci_hcd 0000:00:1d.7: irq 20, io mem 0x50704800
[ 2.321030] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 2.321057] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.321061] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.321064] usb usb2: Product: EHCI Host Controller
[ 2.321067] usb usb2: Manufacturer: Linux 2.6.32-5-amd64 ehci_hcd
[ 2.321071] usb usb2: SerialNumber: 0000:00:1d.7
[ 2.321159] usb usb2: configuration #1 chosen from 1 choice
[ 2.321185] hub 2-0:1.0: USB hub found
[ 2.321191] hub 2-0:1.0: 6 ports detected
[ 2.328368] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.328427] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 2.328437] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 2.328441] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.328450] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 2.328481] uhci_hcd 0000:00:1a.0: irq 20, io base 0x000060c0
[ 2.328620] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.328623] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.328625] usb usb3: Product: UHCI Host Controller
[ 2.328627] usb usb3: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.328628] usb usb3: SerialNumber: 0000:00:1a.0
[ 2.328735] usb usb3: configuration #1 chosen from 1 choice
[ 2.328795] hub 3-0:1.0: USB hub found
[ 2.328801] hub 3-0:1.0: 2 ports detected
[ 2.328851] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 2.328858] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 2.328862] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 2.328901] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 2.328940] uhci_hcd 0000:00:1a.1: irq 16, io base 0x000060a0
[ 2.328975] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.328977] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.328979] usb usb4: Product: UHCI Host Controller
[ 2.328981] usb usb4: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.328983] usb usb4: SerialNumber: 0000:00:1a.1
[ 2.329081] usb usb4: configuration #1 chosen from 1 choice
[ 2.329136] hub 4-0:1.0: USB hub found
[ 2.329143] hub 4-0:1.0: 2 ports detected
[ 2.329192] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.329199] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.329202] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.329214] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 2.329244] uhci_hcd 0000:00:1d.0: irq 16, io base 0x00006080
[ 2.329280] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.329282] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.329284] usb usb5: Product: UHCI Host Controller
[ 2.329286] usb usb5: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.329288] usb usb5: SerialNumber: 0000:00:1d.0
[ 2.329344] usb usb5: configuration #1 chosen from 1 choice
[ 2.329374] hub 5-0:1.0: USB hub found
[ 2.329380] hub 5-0:1.0: 2 ports detected
[ 2.329428] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18
[ 2.329435] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.329438] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.329444] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 2.329474] uhci_hcd 0000:00:1d.1: irq 18, io base 0x00006060
[ 2.329510] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.329513] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.329515] usb usb6: Product: UHCI Host Controller
[ 2.329516] usb usb6: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.329518] usb usb6: SerialNumber: 0000:00:1d.1
[ 2.329572] usb usb6: configuration #1 chosen from 1 choice
[ 2.329597] hub 6-0:1.0: USB hub found
[ 2.329603] hub 6-0:1.0: 2 ports detected
[ 2.329654] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 2.329661] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 2.329664] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 2.329671] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 2.329701] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00006040
[ 2.329736] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.329739] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.329741] usb usb7: Product: UHCI Host Controller
[ 2.329742] usb usb7: Manufacturer: Linux 2.6.32-5-amd64 uhci_hcd
[ 2.329744] usb usb7: SerialNumber: 0000:00:1d.2
[ 2.329796] usb usb7: configuration #1 chosen from 1 choice
[ 2.329825] hub 7-0:1.0: USB hub found
[ 2.329830] hub 7-0:1.0: 2 ports detected
[ 2.351509] b43-pci-bridge 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.351519] b43-pci-bridge 0000:02:00.0: setting latency timer to 64
[ 2.420159] ssb: Sonics Silicon Backplane found on PCI device 0000:02:00.0
[ 2.457812] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 2.457818] Uniform CD-ROM driver Revision: 3.20
[ 2.457938] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 2.724147] usb 2-4: new high speed USB device using ehci_hcd and address 2
[ 2.860966] usb 2-4: New USB device found, idVendor=05ac, idProduct=8501
[ 2.860971] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.860975] usb 2-4: Product: Built-in iSight
[ 2.860978] usb 2-4: Manufacturer: Micron
[ 2.861089] usb 2-4: configuration #1 chosen from 1 choice
[ 2.892086] alloc irq_desc for 19 on node -1
[ 2.892090] alloc kstat_irqs on node -1
[ 2.892098] firewire_ohci 0000:04:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 2.956968] sky2 driver version 1.28
[ 2.957070] sky2 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 2.957118] sky2 0000:03:00.0: setting latency timer to 64
[ 2.957201] sky2 0000:03:00.0: Yukon-2 EC Ultra chip revision 3
[ 2.957718] alloc irq_desc for 27 on node -1
[ 2.957720] alloc kstat_irqs on node -1
[ 2.957788] sky2 0000:03:00.0: irq 27 for MSI/MSI-X
[ 2.958804] sky2 eth0: addr 00:1f:f3:d0:50:7f
[ 2.962776] [drm] Initialized drm 1.1.0 20060810
[ 2.965514] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 2.965631] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 2.968050] firewire_ohci: Added fw-ohci device 0000:04:03.0, OHCI version 1.0
[ 3.009896] applesmc: Apple MacBook 4 detected:
[ 3.009898] applesmc: - Model with accelerometer
[ 3.009900] applesmc: - Model without light sensors and backlight
[ 3.009902] applesmc: - Model with 10 temperature sensors
[ 3.010931] applesmc: device has already been initialized (0xe0, 0xf8).
[ 3.010933] applesmc: device successfully initialized.
[ 3.011605] applesmc: 1 fans found.
[ 3.013935] input: applesmc as /devices/platform/applesmc.768/input/input7
[ 3.013988] applesmc: driver successfully loaded.
[ 3.065161] Error: Driver 'pcspkr' is already registered, aborting...
[ 3.114271] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.114276] i915 0000:00:02.0: setting latency timer to 64
[ 3.126768] alloc irq_desc for 28 on node -1
[ 3.126772] alloc kstat_irqs on node -1
[ 3.126782] i915 0000:00:02.0: irq 28 for MSI/MSI-X
[ 3.126789] [drm] set up 15M of stolen space
[ 3.269027] usb 3-1: new full speed USB device using uhci_hcd and address 2
[ 3.448533] usb 3-1: New USB device found, idVendor=05ac, idProduct=1000
[ 3.448536] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3.448611] usb 3-1: configuration #1 chosen from 1 choice
[ 3.465084] firewire_core: created device fw0: GUID 001ff3fffe89db70, S400
[ 3.578888] [drm] initialized overlay support
[ 3.693031] usb 7-1: new low speed USB device using uhci_hcd and address 2
[ 3.869773] usb 7-1: New USB device found, idVendor=05ac, idProduct=8242
[ 3.869777] usb 7-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.869781] usb 7-1: Product: IR Receiver
[ 3.869784] usb 7-1: Manufacturer: Apple Computer, Inc.
[ 3.869877] usb 7-1: configuration #1 chosen from 1 choice
[ 3.922868] usbcore: registered new interface driver hiddev
[ 3.939766] input: HID 05ac:1000 as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.0/input/input8
[ 3.939887] generic-usb 0003:05AC:1000.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1a.0-1/input0
[ 3.939970] usbcore: registered new interface driver usbhid
[ 3.940072] usbhid: v2.6:USB HID core driver
[ 3.979275] apple 0003:05AC:8242.0002: hiddev0,hidraw1: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-1/input0
[ 4.120104] usb 7-2: new full speed USB device using uhci_hcd and address 3
[ 4.273122] Console: switching to colour frame buffer device 160x50
[ 4.275902] fb0: inteldrmfb frame buffer device
[ 4.275904] registered panic notifier
[ 4.275910] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.275967] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 4.275994] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 4.308769] usb 7-2: New USB device found, idVendor=05ac, idProduct=0229
[ 4.308774] usb 7-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 4.308778] usb 7-2: Product: Apple Internal Keyboard / Trackpad
[ 4.308781] usb 7-2: Manufacturer: Apple Computer
[ 4.308885] usb 7-2: configuration #1 chosen from 1 choice
[ 4.319053] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.0/input/input9
[ 4.319123] apple 0003:05AC:0229.0003: input,hidraw2: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input0
[ 4.326856] input: Apple Computer Apple Internal Keyboard / Trackpad as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.2/input/input10
[ 4.326924] apple 0003:05AC:0229.0004: input,hidraw3: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.2-2/input2
[ 4.338553] usb 3-1: usbfs: USBDEVFS_CONTROL failed cmd hid2hci rqt 64 rq 0 len 0 ret -84
[ 4.346757] appletouch: Geyser mode initialized.
[ 4.346845] input: appletouch as /devices/pci0000:00/0000:00:1d.2/usb7/7-2/7-2:1.1/input/input11
[ 4.346946] usbcore: registered new interface driver appletouch
[ 4.368096] usb 3-1: USB disconnect, address 2
[ 4.373186] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input12
[ 4.715425] Adding 1953116k swap on /dev/sda4. Priority:-1 extents:1 across:1953116k
[ 5.073514] loop: module loaded
[ 5.112102] usb 3-1: new full speed USB device using uhci_hcd and address 3
[ 5.306541] usb 3-1: New USB device found, idVendor=05ac, idProduct=8205
[ 5.306544] usb 3-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.306634] usb 3-1: configuration #1 chosen from 1 choice
[ 5.382766] Bluetooth: Core ver 2.15
[ 5.383031] NET: Registered protocol family 31
[ 5.383031] Bluetooth: HCI device and connection manager initialized
[ 5.383033] Bluetooth: HCI socket layer initialized
[ 5.397507] Bluetooth: Generic Bluetooth USB driver ver 0.6
[ 5.397678] usbcore: registered new interface driver btusb
[ 6.386316] EXT4-fs (sda3): mounted filesystem with ordered data mode
[ 6.417837] EXT4-fs (dm-5): mounted filesystem with ordered data mode
[ 6.436261] EXT4-fs (dm-3): mounted filesystem with ordered data mode
[ 6.454668] EXT4-fs (dm-1): mounted filesystem with ordered data mode
[ 6.492523] EXT4-fs (dm-2): mounted filesystem with ordered data mode
[ 6.515481] EXT4-fs (dm-4): mounted filesystem with ordered data mode
[ 7.167923] sky2 eth0: enabling interface
[ 7.168128] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.905543] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[ 8.905700] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 19.872100] eth0: no IPv6 routers present
----------------------------------------------------------------------

--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110405121249.GA12143@mbu.iisc.ernet.in">http://lists.debian.org/20110405121249.GA12143@mbu.iisc.ernet.in

Davide Baldini 04-09-2011 09:27 PM

Debian on a Macbook (Leopard): Xorg installation leads to blank screen on reboot
 
GM965 graphics controller is well supported now and should work
on defaults with your 2.6.32-5 kernel.

By the first boot you told to start X you needed to manually
issue startx.
But since the second boot, standing at your description, the
blanked screen after "some textlines" rolled up, would suggest
me X is trying to run by itself.
If you made some changes or installs in between, I'd check
them, especially regarding hald and xorg.conf.


--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

Archive: inqj0l$ne$1@dough.gmane.org">http://lists.debian.org/inqj0l$ne$1@dough.gmane.org

shawn wilson 04-10-2011 09:04 AM

Debian on a Macbook (Leopard): Xorg installation leads to blank screen on reboot
 
You must be really comfortable in your relationship (or want a quick escape from it) :)


At any rate, a virtual might serve you better. Either way, to debug this you should start without x - run level 1 IIRC. Or switch to another vt. Then, you can see what's happening - ps, tail -f, etc.


Btw, did you include the xorg log?

Arvind 04-11-2011 04:06 PM

Debian on a Macbook (Leopard): Xorg installation leads to blank screen on reboot
 
On Sat, Apr 09, 2011 at 11:27:48PM +0200, Davide Baldini wrote:
> GM965 graphics controller is well supported now and should work
> on defaults with your 2.6.32-5 kernel.
>
> By the first boot you told to start X you needed to manually
> issue startx.
> But since the second boot, standing at your description, the
> blanked screen after "some textlines" rolled up, would suggest
> me X is trying to run by itself.

No, as far as i can tell, X is not trying to start at boot - i have
not installed packages such as X/G/KDM, which do that.

As you can see from my other mail in this thread (with changed subject
line), i have narrowed down the problem to the package
xserver-xorg-video-intel. When that package is installed, even if i
select "recovery mode" at the grub prompt, i eventually reach a black
screen. I think that should rule out any possibility of X trying to
start at boot and causing a blank screen.

> If you made some changes or installs in between, I'd check
> them, especially regarding hald and xorg.conf.

No, i haven't.

Thanks,
arvind

--
Quidquid latine dictum sit, altum sonatur.

--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110411160659.GA1902@mbu.iisc.ernet.in">http://lists.debian.org/20110411160659.GA1902@mbu.iisc.ernet.in

Arvind 04-11-2011 04:21 PM

Debian on a Macbook (Leopard): Xorg installation leads to blank screen on reboot
 
On Sun, Apr 10, 2011 at 05:04:41AM -0400, shawn wilson wrote:
> You must be really comfortable in your relationship (or want a quick escape
> from it) :)

:-)
She is no geek, and is not passionate about computers, but fortunately
she prefers the keyboard over the mouse/touchpad, and if she is told
about some of the basic keyboard shortcuts, she manages very well.
Since a basic X + window manager setup allows that, she prefers it
over windows or OS X. That way, i am lucky :-)

> At any rate, a virtual might serve you better. Either way, to debug this you
> should start without x - run level 1 IIRC. Or switch to another vt. Then,
> you can see what's happening - ps, tail -f, etc.

As you can see from my other mail in this thread (with changed subject
line), i have narrowed down the problem to the package
xserver-xorg-video-intel. As i mentioned in my reply to Davide, when
that package is installed, even if i select "recovery mode" at the
grub prompt, i eventually reach a black screen.

Also, when i get a blank screen, i have tried key combinations such as
ctrl-alt-fn-F1/2/3/4/5/6 - nothing, the screen remains blank. So i
have no way of using any VT.

> Btw, did you include the xorg log?

I didn't. I am at my workplace, and the machine is at my home, so
cannot do it right away. But it gets generated only when X starts,
right? So suppose i install the package xserver-xorg-video-intel, then
issue the 'startx' command, and attach the /var/log/Xorg.0.log file.
But the blank screen problem will occur when i reboot. So would the
xorg log file help?

Thanks,
arvind

--
Quidquid latine dictum sit, altum sonatur.

--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.


--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110411162112.GB1902@mbu.iisc.ernet.in">http://lists.debian.org/20110411162112.GB1902@mbu.iisc.ernet.in


All times are GMT. The time now is 03:51 AM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.