FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian User

 
 
LinkBack Thread Tools
 
Old 07-13-2010, 09:37 AM
Peppe
 
Default Problems with ISA non-pnp card

Hi all,
I am working on an single board computer (Diamond Systems' Pegasus) running Debian Lenny with a custom-built kernel for the Pegasus Board, version 2.6.29.
Connected to this board I have a GPIO card (Diamond Systems' GPIO-MM) that is a ISA non-PnP card.
Well, I can't use the card: the driver has the same output on the SBC and on my laptop that doesn't have the GPIO card mounted on.

Assuming that the GPIO card works correctly, there are 2 possibilities:
1) the board or the driver aren't configured correctly
2) the SBC doesn't access properly the ISA bus
3) BIOS (?)

1) the board has a Jumper selection for its i/o address range for the ISA bus: I selected 0x40 - 0x7F, and these addresses, according to the scanport command (attached) are free.
The on-board selected IRQs are 7 and 11, free according to /proc/interrupts (attached)
The same i/o address and IRQ are specified in the driver, so the driver should be configured correctly.

2) the kernel finds the EISA bus, and it has the needed driver: the ISA bridge is shown in lspci (attached) and in dmesg (attached) the EISA bus 0 is mentioned but there are 2 errors in configuring the slots:
[ 2.537285] Cannot allocate resource for EISA slot 1
[ 2.537339] Cannot allocate resource for EISA slot 6

3) In the BIOS setup there are some settings about the IT8888 ISA bridge for address decoding and so on that I left blank. I also disabled the PnP OS setting.

I think the problem is in the messages I copied from dmesg, but I couldn't find a way to fix them, but I can be wrong: that's why I wrote a global view.

Thanks for your patience, any help will be appreciated.

Peppe

----------------
Scanport:

The following devices are registered above 0x100:
0x170 -> 0x177 0000:00:0f.2
0x1f0 -> 0x1f7 0000:00:0f.2
0x1 -> 0x1f7 f0-01f7 : cs5536
0x2f8 -> 0x2ff serial
0x376 -> 0x376 0000:00:0f.2
0x3c0 -> 0x3df vga+
0x3f6 -> 0x3f6 0000:00:0f.2
0x3 -> 0x3f6 f6-03f6 : cs5536
0x3f8 -> 0x3ff serial
0xcf8 -> 0xcff PCI conf1
0x1000 -> 0x101f 0000:00:0f.0
0x6000 -> 0x6007 0000:00:0f.0
0x60 -> 0x6007 00-6007 : CS5536 ACB0
0x6100 -> 0x61ff 0000:00:0f.0
0x61 -> 0x61ff 00-61ff : cs5535_gpio
0x6200 -> 0x623f 0000:00:0f.0
0x9c00 -> 0x9c3f 0000:00:0f.0
0x9d00 -> 0x9d7f 0000:00:0f.0
0xac1c -> 0xac1f 0000:00:01.0
0xfc00 -> 0xfcff 0000:00:07.0
0xfc -> 0xfcff 00-fcff : 8139too
0xff00 -> 0xff0f 0000:00:0f.2
0xff -> 0xff0f 00-ff0f : cs5536
and their i/o ports will not be scanned.


WARNING: Reading i/o ports of some hardware may hang your machine
You have 5 seconds to hit ^C (control+c) to abort...

Scanning for non 0xff values from 0x100 to 0x400....

Skipping 0x1 -> 0x1f7 [ f0-01f7 : cs5536 ]
Skipping 0x3 -> 0x3f6 [ f6-03f6 : cs5536 ]
Skipping 0x60 -> 0x6007 [ 00-6007 : CS5536 ACB0 ]

Done.

---------------------------------
/proc/interrupts:

CPU0
0: 223113 XT-PIC-XT timer
1: 4 XT-PIC-XT i8042
2: 0 XT-PIC-XT cascade
5: 74331 XT-PIC-XT ehci_hcd:usb1, ohci_hcd:usb2
8: 2 XT-PIC-XT rtc0
10: 2 XT-PIC-XT
14: 1460 XT-PIC-XT ide0
NMI: 0 Non-maskable interrupts
TRM: 0 Thermal event interrupts
ERR: 0


-------------------------
lspci:

00:01.0 Host bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] Host Bridge (rev 33)
00:01.1 VGA compatible controller: Advanced Micro Devices [AMD] Geode LX Video
00:01.2 Entertainment encryption device: Advanced Micro Devices [AMD] Geode LX AES Security Block
00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
00:08.0 Bridge: Integrated Technology Express, Inc. IT8888F PCI to ISA Bridge with SMB (rev 03)
00:0f.0 ISA bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] ISA (rev 03)
00:0f.2 IDE interface: Advanced Micro Devices [AMD] CS5536 [Geode companion] IDE (rev 01)
00:0f.4 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] OHC (rev 02)
00:0f.5 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] EHC (rev 02)

----------------------------------------------
dmesg:

[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.29geode-rtai (unknown) (root@peppe-laptop) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu9) ) #1 Mon Mar 22 08:47:59 CET 2010
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] PAT not supported by CPU.
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
[ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000f7c0000 (usable)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.2 present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] last_pfn = 0xf7c0 max_arch_pfn = 0x100000
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009e800 (usable)
[ 0.000000] modified: 000000000009e800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000000f7c0000 (usable)
[ 0.000000] modified: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] kernel direct mapping tables up to f7c0000 @ 10000-15000
[ 0.000000] RAMDISK: 0f561000 - 0f7afcfb
[ 0.000000] ACPI Error (tbxfroot-0219): A valid RSDP was not found [20081204]
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 247MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0f7c0000
[ 0.000000] low ram: 00000000 - 0f7c0000
[ 0.000000] bootmap 00011000 - 00012ef8
[ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 000f7c0000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000100000 - 0000627aa8] TEXT DATA BSS ==> [0000100000 - 0000627aa8]
[ 0.000000] #2 [000f561000 - 000f7afcfb] RAMDISK ==> [000f561000 - 000f7afcfb]
[ 0.000000] #3 [0000628000 - 000062b000] INIT_PG_TABLE ==> [0000628000 - 000062b000]
[ 0.000000] #4 [000009e000 - 0000100000] BIOS reserved ==> [000009e000 - 0000100000]
[ 0.000000] #5 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
[ 0.000000] #6 [0000011000 - 0000013000] BOOTMAP ==> [0000011000 - 0000013000]
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x0000f7c0
[ 0.000000] HighMem 0x0000f7c0 -> 0x0000f7c0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x0000f7c0
[ 0.000000] On node 0 totalpages: 63310
[ 0.000000] free_area_init_node: node 0, pgdat c052ef10, node_mem_map c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3950 pages, LIFO batch:0
[ 0.000000] Normal zone: 464 pages used for memmap
[ 0.000000] Normal zone: 58864 pages, LIFO batch:15
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 10000000 (gap: f7c0000:f0830000)
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 62814
[ 0.000000] Kernel command line: root=/dev/hdb1 ro quiet
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 498.064 MHz processor.
[ 0.000999] I-pipe 2.4-01: pipeline enabled.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000999] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000999] allocated 1268160 bytes of page_cgroup
[ 0.000999] please try cgroup_disable=memory option if you don't want
[ 0.000999] Memory: 242036k/253696k available (2788k kernel code, 11112k reserved, 1537k data, 368k init, 0k highmem)
[ 0.000999] virtual kernel memory layout:
[ 0.000999] fixmap : 0xfffed000 - 0xfffff000 ( 72 kB)
[ 0.000999] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000999] vmalloc : 0xcffc0000 - 0xff7fe000 ( 760 MB)
[ 0.000999] lowmem : 0xc0000000 - 0xcf7c0000 ( 247 MB)
[ 0.000999] .init : 0xc053c000 - 0xc0598000 ( 368 kB)
[ 0.000999] .data : 0xc03b93fc - 0xc0539bc4 (1537 kB)
[ 0.000999] .text : 0xc0100000 - 0xc03b93fc (2788 kB)
[ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000999] SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.001022] Calibrating delay loop (skipped), value calculated using timer frequency.. 996.12 BogoMIPS (lpj=498064)
[ 0.001101] Security Framework initialized
[ 0.001126] Smack: Initializing.
[ 0.001160] Mount-cache hash table entries: 512
[ 0.001592] Initializing cgroup subsys ns
[ 0.001609] Initializing cgroup subsys cpuacct
[ 0.001625] Initializing cgroup subsys memory
[ 0.001642] Initializing cgroup subsys freezer
[ 0.001657] Initializing cgroup subsys net_cls
[ 0.001696] CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
[ 0.001714] CPU: L2 Cache: 128K (32 bytes/line)
[ 0.001751] CPU: Geode(TM) Integrated Processor by AMD PCS stepping 02
[ 0.001781] Checking 'hlt' instruction... OK.
[ 0.005150] Freeing SMP alternatives: 0k freed
[ 0.006827] net_namespace: 956 bytes
[ 0.007892] regulator: core version 0.5
[ 0.007953] Time: 9:23:17 Date: 07/13/10
[ 0.008088] NET: Registered protocol family 16
[ 0.008150] geode-mfgpt: 0 MFGPT timers available.
[ 0.008165] mfgpt-timer: Could not allocate a MFPGT timer
[ 0.008896] EISA bus registered
[ 0.010965] PCI: PCI BIOS revision 2.10 entry at 0xfaa20, last bus=0
[ 0.010983] PCI: Using configuration type 1 for base access
[ 0.014212] bio: create slab <bio-0> at 0
[ 0.014596] ACPI: Interpreter disabled.
[ 0.015381] SCSI subsystem initialized
[ 0.015612] usbcore: registered new interface driver usbfs
[ 0.015690] usbcore: registered new interface driver hub
[ 0.015843] usbcore: registered new device driver usb
[ 0.016148] PCI: Probing PCI hardware
[ 0.016164] PCI: Probing PCI hardware (bus 00)
[ 0.016529] pci 0000:00:01.0: reg 10 io port: [0xac1c-0xac1f]
[ 0.017571] pci 0000:00:01.1: reg 10 32bit mmio: [0xee000000-0xeeffffff]
[ 0.017701] pci 0000:00:01.1: reg 14 32bit mmio: [0xefff0000-0xefff3fff]
[ 0.017830] pci 0000:00:01.1: reg 18 32bit mmio: [0xeffec000-0xeffeffff]
[ 0.017959] pci 0000:00:01.1: reg 1c 32bit mmio: [0xeffe8000-0xeffebfff]
[ 0.018090] pci 0000:00:01.1: reg 20 32bit mmio: [0xefff8000-0xefffbfff]
[ 0.018784] pci 0000:00:01.2: reg 10 32bit mmio: [0xefff4000-0xefff7fff]
[ 0.019725] pci 0000:00:07.0: reg 10 io port: [0xfc00-0xfcff]
[ 0.019749] pci 0000:00:07.0: reg 14 32bit mmio: [0xeffff000-0xeffff0ff]
[ 0.019823] pci 0000:00:07.0: supports D1 D2
[ 0.019839] pci 0000:00:07.0: PME# supported from D1 D2 D3hot D3cold
[ 0.019859] pci 0000:00:07.0: PME# disabled
[ 0.020187] pci 0000:00:0f.0: reg 10 io port: [0x6000-0x6007]
[ 0.020305] pci 0000:00:0f.0: reg 14 io port: [0x6100-0x61ff]
[ 0.020423] pci 0000:00:0f.0: reg 18 io port: [0x6200-0x623f]
[ 0.020546] pci 0000:00:0f.0: reg 1c io port: [0x00-0x1f]
[ 0.020666] pci 0000:00:0f.0: reg 20 io port: [0x9d00-0x9d7f]
[ 0.020791] pci 0000:00:0f.0: reg 24 io port: [0x9c00-0x9c3f]
[ 0.021762] pci 0000:00:0f.2: reg 20 io port: [0xff00-0xff0f]
[ 0.022571] pci 0000:00:0f.4: reg 10 32bit mmio: [0xefffe000-0xefffefff]
[ 0.023695] pci 0000:00:0f.4: PME# supported from D0 D3hot D3cold
[ 0.023765] pci 0000:00:0f.4: PME# disabled
[ 0.024235] pci 0000:00:0f.5: reg 10 32bit mmio: [0xefffd000-0xefffdfff]
[ 0.025339] pci 0000:00:0f.5: PME# supported from D0 D3hot D3cold
[ 0.025408] pci 0000:00:0f.5: PME# disabled
[ 0.028276] cfg80211: Calling CRDA to update world regulatory domain
[ 0.028316] cfg80211: calling CRDA failed - unable to update world regulatory domain, using static definition
[ 0.028412] NetLabel: Initializing
[ 0.028424] NetLabel: domain hash size = 128
[ 0.028437] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.028505] NetLabel: unlabeled traffic allowed by default
[ 0.028758] pnp: PnP ACPI: disabled
[ 0.028774] PnPBIOS: Scanning system for PnP BIOS support...
[ 0.029039] Switched to high resolution mode on CPU 0
[ 0.029198] PnPBIOS: Found PnP BIOS installation structure at 0xc00fb3b0
[ 0.029223] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xb3e0, dseg 0xf0000
[ 0.031247] PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
[ 0.031312] system 00:07: iomem range 0x0-0x9ffff could not be reserved
[ 0.031335] system 00:07: iomem range 0xfffc0000-0xffffffff could not be reserved
[ 0.031358] system 00:07: iomem range 0xfee00000-0xfee0ffff has been reserved
[ 0.031381] system 00:07: iomem range 0x100000-0xffffff could not be reserved
[ 0.031416] system 00:08: iomem range 0xe0000-0xeffff has been reserved
[ 0.031439] system 00:08: iomem range 0xf0000-0xf3fff could not be reserved
[ 0.031461] system 00:08: iomem range 0xf4000-0xf7fff could not be reserved
[ 0.031484] system 00:08: iomem range 0xf8000-0xfffff could not be reserved
[ 0.031506] system 00:08: iomem range 0xcd400-0xcffff has been reserved
[ 0.032278] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.032297] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.032450] NET: Registered protocol family 2
[ 0.032947] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.034525] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.034729] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.034880] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.034897] TCP reno registered
[ 0.035179] NET: Registered protocol family 1
[ 0.035861] checking if image is initramfs... it is
[ 1.295299] Freeing initrd memory: 2363k freed
[ 1.295739] scx200: NatSemi SCx200 Driver
[ 1.295846] Scanning for low memory corruption every 60 seconds
[ 1.296315] audit: initializing netlink socket (disabled)
[ 1.296368] type=2000 audit(1279012998.296:1): initialized
[ 1.367409] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.376833] VFS: Disk quotas dquot_6.5.2
[ 1.377213] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.379982] fuse init (API version 7.11)
[ 1.380601] msgmni has been set to 477
[ 1.382250] alg: No test for stdrng (krng)
[ 1.382312] io scheduler noop registered
[ 1.382326] io scheduler anticipatory registered
[ 1.382341] io scheduler deadline registered
[ 1.382449] io scheduler cfq registered (default)
[ 1.382558] pci 0000:00:01.1: Boot video device
[ 1.393446] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.393579] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.395434] lxfb 0000:00:01.1: 8192 KB of video memory at 0xee000000
[ 1.403212] fbcon: Geode LX (fb0) is primary device
[ 1.413654] Console: switching to colour frame buffer device 80x30
[ 1.421909] fb0: Geode LX frame buffer device
[ 1.422243] vga16fb: initializing
[ 1.422257] vga16fb: mapped to 0xc00a0000
[ 1.422430] fb1: VGA16 VGA frame buffer device
[ 1.422681] isapnp: Scanning for PnP cards...
[ 1.781080] isapnp: No Plug & Play device found
[ 1.787481] AMD Geode RNG detected
[ 1.787592] cs5535_gpio: base=0x6100 mask=0xb003c66 major=253
[ 1.787618] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.787859] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.788111] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.789418] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.789879] 00:0f: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.794035] brd: module loaded
[ 1.795821] loop: module loaded
[ 1.795835] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI
[ 1.795852] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.796105] PPP generic driver version 2.4.2
[ 1.796289] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.796310] 8139cp 0000:00:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.796410] 8139too Fast Ethernet driver 0.9.28
[ 1.798164] eth0: RealTek RTL8139 at 0xfc00, 00:05:b7:08:e0:db, IRQ 11
[ 1.798182] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 1.798332] usbcore: registered new interface driver zd1201
[ 1.798413] usbcore: registered new interface driver rt73usb
[ 1.798433] Uniform Multi-Platform E-IDE driver
[ 1.798695] cs5536 0000:00:0f.2: IDE controller (0x1022:0x209a rev 0x01)
[ 1.798811] cs5536 0000:00:0f.2: not 100% native mode: will probe irqs later
[ 1.798861] ide0: BM-DMA at 0xff00-0xff07
[ 1.798913] Probing IDE interface ide0...
[ 2.388308] hdb: 2GB NANDrive, CFA DISK drive
[ 2.439168] hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
[ 2.439354] hdb: UDMA/66 mode selected
[ 2.439492] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 2.439821] ide-gd driver 1.18
[ 2.439910] hdb: max request size: 128KiB
[ 2.439928] hdb: 4000752 sectors (2048 MB) w/1KiB Cache, CHS=3969/16/63
[ 2.439953] hdb: cache flushes not supported
[ 2.440164] hdb: hdb1 hdb2 < hdb5 >
[ 2.448200] Driver 'sd' needs updating - please use bus_type methods
[ 2.448260] Driver 'sr' needs updating - please use bus_type methods
[ 2.448746] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.449103] ehci_hcd 0000:00:0f.5: setting latency timer to 64
[ 2.449145] ehci_hcd 0000:00:0f.5: EHCI Host Controller
[ 2.449438] ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 1
[ 2.470248] ehci_hcd 0000:00:0f.5: irq 5, io mem 0xefffd000
[ 2.476054] ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00
[ 2.476454] usb usb1: configuration #1 chosen from 1 choice
[ 2.476618] hub 1-0:1.0: USB hub found
[ 2.476658] hub 1-0:1.0: 4 ports detected
[ 2.477193] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.477476] ohci_hcd 0000:00:0f.4: setting latency timer to 64
[ 2.477517] ohci_hcd 0000:00:0f.4: OHCI Host Controller
[ 2.477764] ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 2
[ 2.477819] ohci_hcd 0000:00:0f.4: irq 5, io mem 0xefffe000
[ 2.534397] usb usb2: configuration #1 chosen from 1 choice
[ 2.534550] hub 2-0:1.0: USB hub found
[ 2.534590] hub 2-0:1.0: 4 ports detected
[ 2.535043] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.535457] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 2.535476] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 2.535904] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.536064] mice: PS/2 mouse device common for all mice
[ 2.536353] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 2.536406] rtc0: alarms up to one day, 114 bytes nvram
[ 2.536854] geodewdt: No timers were available
[ 2.537260] EISA: Probing bus 0 at eisa.0
[ 2.537285] Cannot allocate resource for EISA slot 1
[ 2.537339] Cannot allocate resource for EISA slot 6
[ 2.537373] EISA: Detected 0 cards.
[ 2.537687] cpuidle: using governor ladder
[ 2.537701] cpuidle: using governor menu
[ 2.538443] geode-aes: GEODE AES engine enabled.
[ 2.541895] TCP cubic registered
[ 2.542916] NET: Registered protocol family 10
[ 2.545641] lo: Disabled Privacy Extensions
[ 2.549533] NET: Registered protocol family 17
[ 2.549566] powernow-k8: Processor cpuid 5a2 not supported
[ 2.549612] Using IPI Shortcut mode
[ 2.550042] registered taskstats version 1
[ 2.550554] Magic number: 2:757:373
[ 2.550743] rtc_cmos 00:03: setting system clock to 2010-07-13 09:23:20 UTC (1279013000)
[ 2.550765] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.550781] EDD information not available.
[ 2.551441] Freeing unused kernel memory: 368k freed
[ 2.778105] usb 1-3: new high speed USB device using ehci_hcd and address 2
[ 3.039452] usb 1-3: configuration #1 chosen from 1 choice
[ 3.303334] wmaster0 (rt73usb): not using net_device_ops yet
[ 3.307617] phy0: Selected rate control algorithm 'minstrel'
[ 3.334636] wlan0 (rt73usb): not using net_device_ops yet
[ 4.339830] PM: Starting manual resume from disk
[ 4.339852] PM: Resume from partition 3:69
[ 4.339865] PM: Checking hibernation image.
[ 4.340539] PM: Resume from disk failed.
[ 4.360251] kjournald starting. Commit interval 5 seconds
[ 4.360303] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.331561] udevd version 125 started
[ 5.976819] udev: renamed network interface wlan0 to eth1
[ 8.585277] Adding 152576k swap on /dev/hdb5. Priority:-1 extents:1 across:152576k
[ 8.708919] EXT3 FS on hdb1, internal journal
[ 11.250013] rt73usb 1-3:1.0: firmware: requesting rt73.bin
[ 11.368679] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 16.745606] eth1: direct probe to AP 00:1f:1f:58:82:e8 try 1
[ 16.747999] eth1 direct probe responded
[ 16.748044] eth1: authenticate with AP 00:1f:1f:58:82:e8
[ 16.755491] eth1: authenticated
[ 16.755506] eth1: associate with AP 00:1f:1f:58:82:e8
[ 16.757991] eth1: RX AssocResp from 00:1f:1f:58:82:e8 (capab=0x411 status=0 aid=1)
[ 16.758037] eth1: associated
[ 16.772001] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 27.155046] eth1: no IPv6 routers present

__________________________________________________ __________
Send your photos by email in seconds...
TRY FREE IM TOOLPACK at http://www.imtoolpack.com/default.aspx?rc=if3
Works in all emails, instant messengers, blogs, forums and social networks.


--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 0431615E5EA.000005B4scaricoapalla@fastwebnet.it">h ttp://lists.debian.org/0431615E5EA.000005B4scaricoapalla@fastwebnet.it
 

Thread Tools




All times are GMT. The time now is 12:07 AM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org