FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian User

 
 
LinkBack Thread Tools
 
Old 01-19-2009, 07:16 PM
"Wim de Vries"
 
Default usb problem with asus eee pc 900 debian

Hi,
I am trying to connect an USB device to my asus eee pc.
The device connects OK on my HP compaq 6910p with Suse 10.3:
dmesg:
usb 7-1: new full speed USB device using uhci_hcd and address 4
usb 7-1: new device found, idVendor=04d8, idProduct=000a
usb 7-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 7-1: Product: PIC18 USB CDC
usb 7-1: Manufacturer: Microchip
usb 7-1: SerialNumber: V1.1FS
usb 7-1: configuration #1 chosen from 1 choice
drivers/usb/class/cdc-acm.c: This device cannot do calls on its own. It
is no; modem.
cdc_acm 7-1:1.0: ttyACM0: USB ACM device

so it should ánd can use cdc-acm
kernel version: 2.6.26-1-686
dmesg:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-1-686 (Debian 2.6.26-11)
(waldi@debian.org) (gcc version 4.1.3 20080623 (prerelease) (Debian
4.1.2-23)) #1 SMP Wed Nov 26 19:14:11 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f780000 (usable)
[ 0.000000] BIOS-e820: 000000003f780000 - 000000003f790000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f790000 - 000000003f7d0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f7d0000 - 000000003f7de000 (reserved)
[ 0.000000] BIOS-e820: 000000003f7e0000 - 000000003f800000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[ 0.000000] 119MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at [c00ff780] 000ff780
[ 0.000000] Entering add_active_range(0, 0, 259968) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 259968
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 259968
[ 0.000000] On node 0 totalpages: 259968
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 239 pages used for memmap
[ 0.000000] HighMem zone: 30353 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000FBE60, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 3F780000, 0034 (r1 A M I OEMRSDT 9000811 MSFT
97)
[ 0.000000] ACPI: FACP 3F780200, 0081 (r1 A M I OEMFACP 9000811 MSFT
97)
[ 0.000000] ACPI: DSDT 3F780400, 6109 (r1 A0979 A0979034 34 INTL
20060113)
[ 0.000000] ACPI: FACS 3F790000, 0040
[ 0.000000] ACPI: APIC 3F780390, 0068 (r1 A M I OEMAPIC 9000811 MSFT
97)
[ 0.000000] ACPI: OEMB 3F790040, 0046 (r1 A M I AMI_OEM 9000811 MSFT
97)
[ 0.000000] ACPI: MCFG 3F786510, 003C (r1 A M I OEMMCFG 9000811 MSFT
97)
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option.
[ 0.000000] Using ACPI for processor (LAPIC) configuration information
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] MPTABLE: OEM ID: INTEL Product ID: <6>MPTABLE: Product
ID: <6>MPTABLE: APIC at: 0xFEE00000
[ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Processors: 1
[ 0.000000] Allocating PCI resources starting at 40000000 (gap:
3f800000:bf600000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 -
0000000000100000
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37960 bytes of per cpu data
[ 0.000000] NR_CPUS: 8, nr_cpu_ids: 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 257937
[ 0.000000] Kernel command line: root=/dev/sdb1 ro quiet noapic
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 900.130 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 1021104k/1039872k available (1768k kernel code,
18032k reserved, 752k data, 244k init, 122368k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xfff4c000 - 0xfffff000 ( 716 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc037f000 - 0xc03bc000 ( 244 kB)
[ 0.004000] .data : 0xc02ba293 - 0xc0376620 ( 752 kB)
[ 0.004000] .text : 0xc0100000 - 0xc02ba293 (1768 kB)
[ 0.004000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084214] Calibrating delay using timer specific routine.. 1802.45
BogoMIPS (lpj=3604919)
[ 0.084287] Security Framework initialized
[ 0.084298] SELinux: Disabled at boot.
[ 0.084308] Capability LSM initialized
[ 0.084334] Mount-cache hash table entries: 512
[ 0.084609] Initializing cgroup subsys ns
[ 0.084617] Initializing cgroup subsys cpuacct
[ 0.084622] Initializing cgroup subsys devices
[ 0.084660] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.084666] CPU: L2 cache: 512K
[ 0.084674] Intel machine check architecture supported.
[ 0.084682] Intel machine check reporting enabled on CPU#0.
[ 0.084705] Checking 'hlt' instruction... OK.
[ 0.100731] SMP alternatives: switching to UP code
[ 0.110392] Freeing SMP alternatives: 16k freed
[ 0.110398] ACPI: Core revision 20080321
[ 0.124464] ACPI: setting ELCR to 0200 (from 0ca8)
[ 0.132008] CPU0: Intel(R) Celeron(R) M processor 900MHz
stepping 08
[ 0.132008] APIC calibration not consistent with PM Timer: 136ms
instead of 100ms
[ 0.132008] APIC delta adjusted to PM-Timer: 625063 (850136)
[ 0.132008] Brought up 1 CPUs
[ 0.132008] Total of 1 processors activated (1802.45 BogoMIPS).
[ 0.132008] CPU0 attaching sched-domain:
[ 0.132008] domain 0: span 0
[ 0.132008] groups: 0
[ 0.132008] net_namespace: 660 bytes
[ 0.132008] Booting paravirtualized kernel on bare hardware
[ 0.132008] NET: Registered protocol family 16
[ 0.132008] ACPI: bus type pci registered
[ 0.132008] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0
- 255
[ 0.132008] PCI: Not using MMCONFIG.
[ 0.132008] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[ 0.132008] PCI: Using configuration type 1 for base access
[ 0.132008] Setting up standard PCI resources
[ 0.144009] ACPI: EC: Look up EC in DSDT
[ 0.159346] ACPI: Interpreter enabled
[ 0.159352] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.159388] ACPI: Using PIC for interrupt routing
[ 0.159511] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0
- 255
[ 0.162710] PCI: MCFG area at e0000000 reserved in ACPI motherboard
resources
[ 0.162716] PCI: Using MMCONFIG for extended config space
[ 0.173511] ACPI: EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
[ 0.173518] ACPI: EC: driver started in poll mode
[ 0.173755] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.174621] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.174633] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6
ACPI/GPIO/TCO
[ 0.174640] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.175178] PCI: Transparent bridge - 0000:00:1e.0
[ 0.175222] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.175798] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[ 0.175995] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[ 0.176243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P6._PRT]
[ 0.184710] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12
14 15)
[ 0.184978] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12
14 15)
[ 0.185241] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12
14 15)
[ 0.185500] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12
14 15)
[ 0.185763] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14
15) *0, disabled.
[ 0.186025] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14
15) *0, disabled.
[ 0.186287] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14
15) *0, disabled.
[ 0.186548] ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12
14 15)
[ 0.186882] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.186950] pnp: PnP ACPI init
[ 0.186965] ACPI: bus type pnp registered
[ 0.191275] pnp: PnP ACPI: found 13 devices
[ 0.191282] ACPI: ACPI bus type pnp unregistered
[ 0.191292] PnPBIOS: Disabled by ACPI PNP
[ 0.191792] PCI: Using ACPI for IRQ routing
[ 0.192357] hpet clockevent registered
[ 0.192369] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.192377] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.193456] ACPI: RTC can wake from S4
[ 0.193513] system 00:01: iomem range 0xfed13000-0xfed19fff has been
reserved
[ 0.193534] system 00:08: ioport range 0x380-0x383 has been reserved
[ 0.193540] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.193546] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.193552] system 00:08: ioport range 0x480-0x4bf has been reserved
[ 0.193559] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been
reserved
[ 0.193565] system 00:08: iomem range 0xfed20000-0xfed8ffff has been
reserved
[ 0.193572] system 00:08: iomem range 0xfff00000-0xffffffff could not
be reserved
[ 0.193584] system 00:09: iomem range 0xfec00000-0xfec00fff has been
reserved
[ 0.193590] system 00:09: iomem range 0xfee00000-0xfee00fff could not
be reserved
[ 0.193602] system 00:0a: iomem range 0xe0000000-0xefffffff has been
reserved
[ 0.193614] system 00:0b: iomem range 0xe0000000-0xefffffff has been
reserved
[ 0.193631] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.193638] system 00:0c: iomem range 0xe0000-0xfffff could not be
reserved
[ 0.193644] system 00:0c: iomem range 0x100000-0x3f7fffff could not be
reserved
[ 0.224415] PCI: Bridge: 0000:00:1c.0
[ 0.224420] IO window: disabled.
[ 0.224427] MEM window: disabled.
[ 0.224433] PREFETCH window: disabled.
[ 0.224441] PCI: Bridge: 0000:00:1c.1
[ 0.224444] IO window: disabled.
[ 0.224451] MEM window: 0xfbf00000-0xfbffffff
[ 0.224457] PREFETCH window: disabled.
[ 0.224465] PCI: Bridge: 0000:00:1c.2
[ 0.224468] IO window: disabled.
[ 0.224475] MEM window: 0xf8000000-0xfbefffff
[ 0.224482] PREFETCH window: 0x00000000f0000000-0x00000000f6ffffff
[ 0.224491] PCI: Bridge: 0000:00:1e.0
[ 0.224494] IO window: disabled.
[ 0.224500] MEM window: disabled.
[ 0.224505] PREFETCH window: disabled.
[ 0.224872] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
[ 0.224878] PCI: setting IRQ 5 as level-triggered
[ 0.224884] ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKA] -> GSI 5
(level, low) -> IRQ 5
[ 0.224896] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.225204] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[ 0.225209] PCI: setting IRQ 11 as level-triggered
[ 0.225215] ACPI: PCI Interrupt 0000:00:1c.1[b] -> Link [LNKB] -> GSI
11 (level, low) -> IRQ 11
[ 0.225226] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.225528] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[ 0.225533] PCI: setting IRQ 10 as level-triggered
[ 0.225539] ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> GSI
10 (level, low) -> IRQ 10
[ 0.225549] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.225564] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.225608] NET: Registered protocol family 2
[ 0.225794] IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.226219] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.227867] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.228708] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.228716] TCP reno registered
[ 0.228952] NET: Registered protocol family 1
[ 0.229175] checking if image is initramfs...<7>Switched to high
resolution mode on CPU 0
[ 0.718795] it is
[ 1.253276] Freeing initrd memory: 5802k freed
[ 1.254324] audit: initializing netlink socket (disabled)
[ 1.254352] type=2000 audit(1232394730.252:1): initialized
[ 1.254614] highmem bounce pool size: 64 pages
[ 1.254625] Total HugeTLB memory allocated, 0
[ 1.254763] VFS: Disk quotas dquot_6.5.1
[ 1.254815] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.254881] msgmni has been set to 1767
[ 1.255090] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 1.255096] io scheduler noop registered
[ 1.255101] io scheduler anticipatory registered
[ 1.255105] io scheduler deadline registered
[ 1.255130] io scheduler cfq registered (default)
[ 1.255155] pci 0000:00:02.0: Boot video device
[ 1.255428] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.255470] assign_interrupt_mode Found MSI capability
[ 1.255513] Allocate Port Service[0000:00:1c.0cie00]
[ 1.255593] Allocate Port Service[0000:00:1c.0cie02]
[ 1.255663] Allocate Port Service[0000:00:1c.0cie03]
[ 1.255788] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 1.255827] assign_interrupt_mode Found MSI capability
[ 1.255867] Allocate Port Service[0000:00:1c.1cie00]
[ 1.255942] Allocate Port Service[0000:00:1c.1cie02]
[ 1.256010] Allocate Port Service[0000:00:1c.1cie03]
[ 1.256157] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 1.256198] assign_interrupt_mode Found MSI capability
[ 1.256237] Allocate Port Service[0000:00:1c.2cie00]
[ 1.256310] Allocate Port Service[0000:00:1c.2cie02]
[ 1.256379] Allocate Port Service[0000:00:1c.2cie03]
[ 1.256929] isapnp: Scanning for PnP cards...
[ 1.610708] isapnp: No Plug & Play device found
[ 1.615603] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 1.619389] brd: module loaded
[ 1.619573] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 1.654990] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.655000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.655304] mice: PS/2 mouse device common for all mice
[ 1.656447] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.656447] rtc0: alarms up to one month
[ 1.656447] cpuidle: using governor ladder
[ 1.656447] cpuidle: using governor menu
[ 1.656447] No iBFT detected.
[ 1.656447] TCP cubic registered
[ 1.656447] NET: Registered protocol family 17
[ 1.656447] Using IPI No-Shortcut mode
[ 1.656447] registered taskstats version 1
[ 1.656447] rtc_cmos 00:03: setting system clock to 2009-01-19 19:52:11
UTC (1232394731)
[ 1.656447] Freeing unused kernel memory: 244k freed
[ 1.679754] input: AT Translated Set 2 keyboard as /class/input/input0
[ 1.830264] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 1.830360] ACPI: ACPI0007:00 is registered as cooling_device0
[ 1.830368] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 1.834937] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 1.835020] Marking TSC unstable due to: TSC halts in idle.
[ 2.023282] ACPI: LNXTHERM:01 is registered as thermal_zone0
[ 2.030790] ACPI: Thermal Zone [TZ00] (62 C)
[ 2.192033] Clocksource tsc unstable (delta = -195791138 ns)
[ 3.165517] usbcore: registered new interface driver usbfs
[ 3.165566] usbcore: registered new interface driver hub
[ 3.165634] usbcore: registered new device driver usb
[ 3.178277] USB Universal Host Controller Interface driver v3.0
[ 3.178707] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
[ 3.178713] PCI: setting IRQ 3 as level-triggered
[ 3.178720] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 3
(level, low) -> IRQ 3
[ 3.178736] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 3.178745] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 3.178937] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 1
[ 3.178974] uhci_hcd 0000:00:1d.0: irq 3, io base 0x0000e400
[ 3.179123] usb usb1: configuration #1 chosen from 1 choice
[ 3.179176] hub 1-0:1.0: USB hub found
[ 3.179188] hub 1-0:1.0: 2 ports detected
[ 3.280222] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.280231] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.280236] usb usb1: Product: UHCI Host Controller
[ 3.280241] usb usb1: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 3.280245] usb usb1: SerialNumber: 0000:00:1d.0
[ 3.280668] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
[ 3.280674] PCI: setting IRQ 7 as level-triggered
[ 3.280680] ACPI: PCI Interrupt 0000:00:1d.1[b] -> Link [LNKD] -> GSI 7
(level, low) -> IRQ 7
[ 3.280699] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 3.280705] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.280755] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 2
[ 3.280789] uhci_hcd 0000:00:1d.1: irq 7, io base 0x0000e480
[ 3.280928] usb usb2: configuration #1 chosen from 1 choice
[ 3.280983] hub 2-0:1.0: USB hub found
[ 3.280997] hub 2-0:1.0: 2 ports detected
[ 3.281906] No dock devices found.
[ 3.352371] SCSI subsystem initialized
[ 3.384238] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.384246] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.384252] usb usb2: Product: UHCI Host Controller
[ 3.384256] usb usb2: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 3.384261] usb usb2: SerialNumber: 0000:00:1d.1
[ 3.384330] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI
10 (level, low) -> IRQ 10
[ 3.384347] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.384354] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.384399] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 3
[ 3.384433] uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000e800
[ 3.384577] usb usb3: configuration #1 chosen from 1 choice
[ 3.384629] hub 3-0:1.0: USB hub found
[ 3.384640] hub 3-0:1.0: 2 ports detected
[ 3.416319] libata version 3.00 loaded.
[ 3.488204] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.488212] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.488218] usb usb3: Product: UHCI Host Controller
[ 3.488223] usb usb3: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 3.488227] usb usb3: SerialNumber: 0000:00:1d.2
[ 3.488303] ACPI: PCI Interrupt 0000:00:1d.3[D] -> Link [LNKA] -> GSI 5
(level, low) -> IRQ 5
[ 3.488320] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 3.488327] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.488378] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus
number 4
[ 3.488413] uhci_hcd 0000:00:1d.3: irq 5, io base 0x0000e880
[ 3.488560] usb usb4: configuration #1 chosen from 1 choice
[ 3.488612] hub 4-0:1.0: USB hub found
[ 3.488625] hub 4-0:1.0: 2 ports detected
[ 3.592215] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.592223] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.592229] usb usb4: Product: UHCI Host Controller
[ 3.592234] usb usb4: Manufacturer: Linux 2.6.26-1-686 uhci_hcd
[ 3.592238] usb usb4: SerialNumber: 0000:00:1d.3
[ 3.593865] ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 3
(level, low) -> IRQ 3
[ 3.593890] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 3.593897] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.593962] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 5
[ 3.597887] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.597896] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[ 3.597911] ehci_hcd 0000:00:1d.7: irq 3, io mem 0xf7eb7c00
[ 3.624100] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 3.636034] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 3.636195] usb usb5: configuration #1 chosen from 1 choice
[ 3.636252] hub 5-0:1.0: USB hub found
[ 3.636267] hub 5-0:1.0: 8 ports detected
[ 3.692091] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 3.740226] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.740234] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 3.740240] usb usb5: Product: EHCI Host Controller
[ 3.740244] usb usb5: Manufacturer: Linux 2.6.26-1-686 ehci_hcd
[ 3.740249] usb usb5: SerialNumber: 0000:00:1d.7
[ 3.740783] ahci 0000:00:1f.2: version 3.0
[ 3.740819] ACPI: PCI Interrupt 0000:00:1f.2[b] -> Link [LNKD] -> GSI 7
(level, low) -> IRQ 7
[ 3.740844] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[ 3.740856] ahci: probe of 0000:00:1f.2 failed with error -22
[ 3.745573] ata_piix 0000:00:1f.2: version 2.12
[ 3.745593] ACPI: PCI Interrupt 0000:00:1f.2[b] -> Link [LNKD] -> GSI 7
(level, low) -> IRQ 7
[ 3.745603] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 3.745666] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 3.745758] scsi0 : ata_piix
[ 3.745903] scsi1 : ata_piix
[ 3.749073] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0
irq 14
[ 3.749080] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8
irq 15
[ 4.092738] ata2.00: ATA-5: ASUS-PHISON OB SSD, TST2.04U, max UDMA/66
[ 4.092746] ata2.00: 7880544 sectors, multi 0: LBA
[ 4.092784] ata2.01: ATA-5: ASUS-PHISON SSD, TST2.04P, max UDMA/66
[ 4.092789] ata2.01: 31522176 sectors, multi 0: LBA
[ 4.100659] ata2.00: configured for UDMA/66
[ 4.108633] ata2.01: configured for UDMA/66
[ 4.108817] scsi 1:0:0:0: Direct-Access ATA ASUS-PHISON OB S
TST2 PQ: 0 ANSI: 5
[ 4.109109] scsi 1:0:1:0: Direct-Access ATA ASUS-PHISON SSD
TST2 PQ: 0 ANSI: 5
[ 4.126696] Uniform Multi-Platform E-IDE driver
[ 4.126708] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[ 4.196148] Driver 'sd' needs updating - please use bus_type methods
[ 4.196314] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors (4035 MB)
[ 4.196348] sd 1:0:0:0: [sda] Write Protect is off
[ 4.196353] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.196409] sd 1:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.196525] sd 1:0:0:0: [sda] 7880544 512-byte hardware sectors (4035 MB)
[ 4.196556] sd 1:0:0:0: [sda] Write Protect is off
[ 4.196563] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.196618] sd 1:0:0:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.196625] sda: sda1
[ 4.198512] sd 1:0:0:0: [sda] Attached SCSI disk
[ 4.198653] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors (16139
MB)
[ 4.198687] sd 1:0:1:0: [sdb] Write Protect is off
[ 4.198693] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.198747] sd 1:0:1:0: [sdb] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.198847] sd 1:0:1:0: [sdb] 31522176 512-byte hardware sectors (16139
MB)
[ 4.198878] sd 1:0:1:0: [sdb] Write Protect is off
[ 4.198884] sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.198937] sd 1:0:1:0: [sdb] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.198945] sdb: sdb1 sdb2 < sdb5 >
[ 4.201758] sd 1:0:1:0: [sdb] Attached SCSI disk
[ 4.392601] PM: Starting manual resume from disk
[ 4.425481] kjournald starting. Commit interval 5 seconds
[ 4.425500] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.744055] usb 5-5: new high speed USB device using ehci_hcd and
address 4
[ 4.877440] usb 5-5: configuration #1 chosen from 1 choice
[ 4.877868] usb 5-5: New USB device found, idVendor=0951, idProduct=1606
[ 4.877875] usb 5-5: New USB device strings: Mfr=1, Product=2,
SerialNumber=4
[ 4.877880] usb 5-5: Product: UB6225
[ 4.877884] usb 5-5: Manufacturer: ENE
[ 4.877888] usb 5-5: SerialNumber: 146030377350
[ 5.116092] usb 5-8: new high speed USB device using ehci_hcd and
address 5
[ 5.128576] udevd version 125 started
[ 5.663525] usb 5-8: configuration #1 chosen from 1 choice
[ 5.665432] usb 5-8: New USB device found, idVendor=05e3, idProduct=0505
[ 5.665440] usb 5-8: New USB device strings: Mfr=0, Product=1,
SerialNumber=0
[ 5.665445] usb 5-8: Product: USB 2.0 Camera
[ 5.904061] usb 2-1: new low speed USB device using uhci_hcd and address 3
[ 6.078974] usb 2-1: configuration #1 chosen from 1 choice
[ 6.092113] usb 2-1: New USB device found, idVendor=093a, idProduct=2510
[ 6.092121] usb 2-1: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 6.092127] usb 2-1: Product: USB OPTICAL MOUSE
[ 6.092131] usb 2-1: Manufacturer: PIXART
[ 6.332049] usb 2-2: new full speed USB device using uhci_hcd and
address 4
[ 6.452049] usb 2-2: device descriptor read/64, error -71
[ 6.676048] usb 2-2: device descriptor read/64, error -71
[ 6.892049] usb 2-2: new full speed USB device using uhci_hcd and
address 5
[ 7.012056] usb 2-2: device descriptor read/64, error -71
[ 7.184041] Linux agpgart interface v0.103
[ 7.217692] agpgart: Detected an Intel 915GM Chipset.
[ 7.217903] agpgart: Detected 7932K stolen memory.
[ 7.238885] agpgart: AGP aperture is 256M @ 0xd0000000
[ 7.238965] usb 2-2: device descriptor read/64, error -71
[ 7.452044] usb 2-2: new full speed USB device using uhci_hcd and
address 6
[ 7.860027] usb 2-2: device not accepting address 6, error -71
[ 7.864253] Atheros(R) L2 Ethernet Driver - version 2.0.5
[ 7.864259] Copyright (c) 2007 Atheros Corporation.
[ 7.864320] ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKB] -> GSI
11 (level, low) -> IRQ 11
[ 7.864339] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 7.972048] usb 2-2: new full speed USB device using uhci_hcd and
address 7
[ 8.153587] ath_hal: module license 'Proprietary' taints kernel.
[ 8.176070] AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413,
RF5413, RF2133, RF2425, RF2417)
[ 8.179523] eeepc: Eee PC Hotkey Driver
[ 8.179764] eeepc: Hotkey init flags 0x41
[ 8.181034] eeepc: Get control methods supported: 0x101711
[ 8.189538] input: Power Button (FF) as /class/input/input1
[ 8.216368] ACPI: Power Button (FF) [PWRF]
[ 8.216521] input: Lid Switch as /class/input/input2
[ 8.245309] ACPI: Lid Switch [LID]
[ 8.245427] input: Sleep Button (CM) as /class/input/input3
[ 8.275834] ACPI: Sleep Button (CM) [SLPB]
[ 8.275940] input: Power Button (CM) as /class/input/input4
[ 8.303486] ACPI: Power Button (CM) [PWRB]
[ 8.384026] usb 2-2: device not accepting address 7, error -71
[ 8.384135] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 8.550914] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI
10 (level, low) -> IRQ 10
[ 8.550934] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 9.042244] MadWifi: ath_attach: Switching rfkill capability off.
[ 9.735124] ACPI: AC Adapter [AC0] (on-line)
[ 10.756737] ACPI: EC: missing confirmations, switch off interrupt mode.
[ 11.208450] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 11.208577] iTCO_wdt: Found a ICH6-M TCO device (Version=2,
TCOBASE=0x0860)
[ 11.208620] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 11.477769] ACPI: PCI Interrupt 0000:00:1b.0[A] -> Link [LNKA] -> GSI 5
(level, low) -> IRQ 5
[ 11.477805] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 11.483562] input: PC Speaker as /class/input/input5
[ 11.501902] hda_codec: Unknown model for ALC662, trying auto-probe from
BIOS...
[ 11.540394] ACPI: Battery Slot [BAT0] (battery present)
[ 11.541343] input: Video Bus as /class/input/input6
[ 11.548119] intel_rng: FWH not detected
[ 11.568109] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 12.410100] Initializing USB Mass Storage driver...
[ 12.410257] scsi2 : SCSI emulation for USB Mass Storage devices
[ 12.410408] usbcore: registered new interface driver usb-storage
[ 12.410415] USB Mass Storage support registered.
[ 12.419980] usb-storage: device found at 4
[ 12.419987] usb-storage: waiting for device to settle before scanning
[ 12.467956] Linux video capture interface: v2.00
[ 12.501378] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (05e3:0505)
[ 12.675603] usbcore: registered new interface driver uvcvideo
[ 12.675612] USB Video Class driver (v0.1.0)
[ 12.690664] usbcore: registered new interface driver hiddev
[ 12.706770] input: PIXART USB OPTICAL MOUSE as /class/input/input7
[ 12.732114] input,hidraw0: USB HID v1.10 Mouse [PIXART USB OPTICAL
MOUSE] on usb-0000:00:1d.1-1
[ 12.732155] usbcore: registered new interface driver usbhid
[ 12.732161] usbhid: v2.6:USB HID core driver
[ 13.367766] wifi0: Atheros AR2425 chip found (MAC 14.2, PHY SChip 7.0,
Radio 10.2)
[ 13.491684] ath_pci: wifi0: Atheros 5424/2424: mem=0xfbef0000, irq=10
[ 13.493167] ACPI: PCI Interrupt 0000:00:1f.3[b] -> Link [LNKD] -> GSI 7
(level, low) -> IRQ 7
[ 14.103195] input: ImPS/2 Logitech Wheel Mouse as /class/input/input8
[ 14.612235] Adding 706820k swap on /dev/sdb5. Priority:-1 extents:1
across:706820k
[ 14.741005] EXT3 FS on sdb1, internal journal
[ 15.148504] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 15.156599] pciehp: HPC vendor_id 8086 device_id 2660 ss_vid 0 ss_did 0
[ 15.156711] Load service driver hpdriver on pcie device
0000:00:1c.0cie02
[ 15.156733] pciehp: HPC vendor_id 8086 device_id 2662 ss_vid 0 ss_did 0
[ 16.160089] pciehp: Device 0000:03:00.0 already exists at 3:0, cannot
hot-add
[ 16.160202] pciehp: Cannot add device 0x3:0
[ 17.164098] Load service driver hpdriver on pcie device
0000:00:1c.1cie02
[ 17.164136] pciehp: HPC vendor_id 8086 device_id 2664 ss_vid 0 ss_did 0
[ 17.416293] usb-storage: device scan complete
[ 17.416756] scsi 2:0:0:0: Direct-Access USB2.0 CardReader SD0
0100 PQ: 0 ANSI: 0
[ 17.418374] sd 2:0:0:0: [sdc] Attached SCSI removable disk
[ 18.168064] pciehp: Device 0000:01:00.0 already exists at 1:0, cannot
hot-add
[ 18.168156] pciehp: Cannot add device 0x1:0
[ 19.172058] Load service driver hpdriver on pcie device
0000:00:1c.2cie02
[ 19.172108] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 32.817916] lp: driver loaded but no devices found
[ 32.878596] ppdev: user-space parallel port driver
[ 33.353445] NET: Registered protocol family 10
[ 33.354326] lo: Disabled Privacy Extensions
[ 33.355270] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 34.573246] warning: `avahi-daemon' uses 32-bit capabilities (legacy
support in use)
[ 43.156412] Bluetooth: Core ver 2.11
[ 43.158622] NET: Registered protocol family 31
[ 43.158632] Bluetooth: HCI device and connection manager initialized
[ 43.158638] Bluetooth: HCI socket layer initialized
[ 43.235432] Bluetooth: L2CAP ver 2.9
[ 43.235441] Bluetooth: L2CAP socket layer initialized
[ 43.311284] Bluetooth: RFCOMM socket layer initialized
[ 43.311306] Bluetooth: RFCOMM TTY layer initialized
[ 43.311310] Bluetooth: RFCOMM ver 1.8
[ 49.437113] [drm] Initialized drm 1.1.0 20060810
[ 50.574435] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 5
(level, low) -> IRQ 5
[ 50.574454] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 50.574592] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 95.536152] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 111.140013] ath0: no IPv6 routers present
[ 321.816064] usb 2-2: new full speed USB device using uhci_hcd and
address 8
[ 321.872078] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 323.056069] usb 2-2: new full speed USB device using uhci_hcd and
address 9
[ 323.198730] usb 2-2: device descriptor read/all, error -71
[ 323.256090] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 324.296074] usb 2-2: new full speed USB device using uhci_hcd and
address 11
[ 324.352091] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 325.536036] usb 2-2: new full speed USB device using uhci_hcd and
address 12
[ 325.686747] usb 2-2: unable to read config index 0 descriptor/all
[ 325.686747] usb 2-2: can't read configurations, error -71
[ 325.744091] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 326.776039] usb 2-2: new full speed USB device using uhci_hcd and
address 14
[ 326.832092] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 328.016070] usb 2-2: new full speed USB device using uhci_hcd and
address 15
[ 328.072161] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 329.256077] usb 2-2: new full speed USB device using uhci_hcd and
address 16
[ 329.312097] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 330.496075] usb 2-2: new full speed USB device using uhci_hcd and
address 17
[ 330.552108] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 331.736069] usb 2-2: new full speed USB device using uhci_hcd and
address 18
[ 331.878747] usb 2-2: device descriptor read/all, error -71
[ 331.936095] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 332.976078] usb 2-2: new full speed USB device using uhci_hcd and
address 20
[ 333.118668] usb 2-2: device descriptor read/all, error -71
[ 333.176108] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 334.216075] usb 2-2: new full speed USB device using uhci_hcd and
address 22
[ 334.272108] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 335.456137] usb 2-2: new full speed USB device using uhci_hcd and
address 23
[ 335.512118] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 336.696071] usb 2-2: new full speed USB device using uhci_hcd and
address 24
[ 336.838739] usb 2-2: device descriptor read/all, error -71
[ 336.896067] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 337.936069] usb 2-2: new full speed USB device using uhci_hcd and
address 26
[ 337.992105] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 339.176075] usb 2-2: new full speed USB device using uhci_hcd and
address 27
[ 339.236097] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 340.416067] usb 2-2: new full speed USB device using uhci_hcd and
address 28
[ 340.476107] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 341.656078] usb 2-2: new full speed USB device using uhci_hcd and
address 29
[ 341.827652] usb 2-2: configuration #1 chosen from 1 choice
[ 341.833292] usb 2-2: can't set config #1, error -71
[ 341.833436] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a
[ 341.833443] usb 2-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 341.833468] usb 2-2: USB disconnect, address 29
[ 342.896078] usb 2-2: new full speed USB device using uhci_hcd and
address 30
[ 342.952095] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 344.136074] usb 2-2: new full speed USB device using uhci_hcd and
address 31
[ 344.192112] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 345.376075] usb 2-2: new full speed USB device using uhci_hcd and
address 32
[ 345.436065] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 346.616073] usb 2-2: new full speed USB device using uhci_hcd and
address 33
[ 346.758870] usb 2-2: device descriptor read/all, error -71
[ 346.816090] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 347.856079] usb 2-2: new full speed USB device using uhci_hcd and
address 35
[ 347.998741] usb 2-2: device descriptor read/all, error -71
[ 348.056093] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 349.096073] usb 2-2: new full speed USB device using uhci_hcd and
address 37
[ 349.246504] usb 2-2: unable to read config index 0 descriptor/all
[ 349.246504] usb 2-2: can't read configurations, error -71
[ 349.304144] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 350.336071] usb 2-2: new full speed USB device using uhci_hcd and
address 39
[ 350.486581] usb 2-2: unable to read config index 0 descriptor/all
[ 350.486581] usb 2-2: can't read configurations, error -71
[ 350.544097] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 351.576075] usb 2-2: new full speed USB device using uhci_hcd and
address 41
[ 351.729542] usb 2-2: unable to read config index 0 descriptor/all
[ 351.729542] usb 2-2: can't read configurations, error -71
[ 351.784099] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 352.816067] usb 2-2: new full speed USB device using uhci_hcd and
address 43
[ 352.872105] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 354.056173] usb 2-2: new full speed USB device using uhci_hcd and
address 44
[ 354.198756] usb 2-2: device descriptor read/all, error -71
[ 354.256102] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 355.296075] usb 2-2: new full speed USB device using uhci_hcd and
address 46
[ 355.446516] usb 2-2: unable to read config index 0 descriptor/all
[ 355.446516] usb 2-2: can't read configurations, error -71
[ 355.504102] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 356.536041] usb 2-2: new full speed USB device using uhci_hcd and
address 48
[ 356.686702] usb 2-2: unable to read config index 0 descriptor/all
[ 356.686702] usb 2-2: can't read configurations, error -71
[ 356.744059] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 357.776045] usb 2-2: new full speed USB device using uhci_hcd and
address 50
[ 357.926582] usb 2-2: unable to read config index 0 descriptor/all
[ 357.926582] usb 2-2: can't read configurations, error -71
[ 357.984071] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 359.016069] usb 2-2: new full speed USB device using uhci_hcd and
address 52
[ 359.072171] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 360.256077] usb 2-2: new full speed USB device using uhci_hcd and
address 53
[ 360.316100] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 361.496046] usb 2-2: new full speed USB device using uhci_hcd and
address 54
[ 361.646872] usb 2-2: unable to read config index 0 descriptor/all
[ 361.646883] usb 2-2: can't read configurations, error -71
[ 361.704071] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 362.736071] usb 2-2: new full speed USB device using uhci_hcd and
address 56
[ 362.878746] usb 2-2: device descriptor read/all, error -71
[ 362.936069] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 363.976081] usb 2-2: new full speed USB device using uhci_hcd and
address 58
[ 364.032099] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 365.216069] usb 2-2: new full speed USB device using uhci_hcd and
address 59
[ 365.361850] usb 2-2: device descriptor read/all, error -71
[ 365.416095] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 366.456076] usb 2-2: new full speed USB device using uhci_hcd and
address 61
[ 366.512099] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 367.696078] usb 2-2: new full speed USB device using uhci_hcd and
address 62
[ 367.838690] usb 2-2: device descriptor read/all, error -71
[ 367.896101] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 368.936044] usb 2-2: new full speed USB device using uhci_hcd and
address 64
[ 368.992106] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 370.176080] usb 2-2: new full speed USB device using uhci_hcd and
address 65
[ 370.232103] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 371.416073] usb 2-2: new full speed USB device using uhci_hcd and
address 66
[ 371.472106] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 372.656082] usb 2-2: new full speed USB device using uhci_hcd and
address 67
[ 372.712103] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 373.896080] usb 2-2: new full speed USB device using uhci_hcd and
address 68
[ 374.045624] usb 2-2: unable to read config index 0 descriptor/start: -71
[ 374.045624] usb 2-2: chopping to 0 config(s)
[ 374.053868] usb 2-2: string descriptor 0 read error: -71
[ 374.061828] usb 2-2: string descriptor 0 read error: -71
[ 374.069525] usb 2-2: string descriptor 0 read error: -71
[ 374.069525] usb 2-2: no configuration chosen from 0 choices
[ 374.069525] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a
[ 374.069525] usb 2-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 374.069525] usb 2-2: USB disconnect, address 68
[ 375.136075] usb 2-2: new full speed USB device using uhci_hcd and
address 69
[ 375.192110] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 376.376083] usb 2-2: new full speed USB device using uhci_hcd and
address 70
[ 376.432100] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 377.616075] usb 2-2: new full speed USB device using uhci_hcd and
address 71
[ 377.767653] usb 2-2: unable to read config index 0 descriptor/all
[ 377.767653] usb 2-2: can't read configurations, error -71
[ 377.824096] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 378.856084] usb 2-2: new full speed USB device using uhci_hcd and
address 73
[ 378.912074] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 380.096078] usb 2-2: new full speed USB device using uhci_hcd and
address 74
[ 380.246755] usb 2-2: unable to read config index 0 descriptor/all
[ 380.246755] usb 2-2: can't read configurations, error -71
[ 380.304106] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 381.336075] usb 2-2: new full speed USB device using uhci_hcd and
address 76
[ 381.392112] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 382.576042] usb 2-2: new full speed USB device using uhci_hcd and
address 77
[ 382.718749] usb 2-2: device descriptor read/all, error -71
[ 382.776103] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 383.816074] usb 2-2: new full speed USB device using uhci_hcd and
address 79
[ 383.966777] usb 2-2: unable to read config index 0 descriptor/all
[ 383.966777] usb 2-2: can't read configurations, error -71
[ 384.024099] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 385.056078] usb 2-2: new full speed USB device using uhci_hcd and
address 81
[ 385.112104] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 386.296083] usb 2-2: new full speed USB device using uhci_hcd and
address 82
[ 386.352162] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 387.536079] usb 2-2: new full speed USB device using uhci_hcd and
address 83
[ 387.592105] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 388.776083] usb 2-2: new full speed USB device using uhci_hcd and
address 84
[ 388.926509] usb 2-2: unable to read config index 0 descriptor/all
[ 388.926509] usb 2-2: can't read configurations, error -71
[ 388.984109] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 390.016074] usb 2-2: new full speed USB device using uhci_hcd and
address 86
[ 390.158884] usb 2-2: device descriptor read/all, error -71
[ 390.216060] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 391.256077] usb 2-2: new full speed USB device using uhci_hcd and
address 88
[ 391.406576] usb 2-2: unable to read config index 0 descriptor/all
[ 391.406576] usb 2-2: can't read configurations, error -71
[ 391.464106] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 392.496156] usb 2-2: new full speed USB device using uhci_hcd and
address 90
[ 392.552101] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 393.736084] usb 2-2: new full speed USB device using uhci_hcd and
address 91
[ 393.792110] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 394.976043] usb 2-2: new full speed USB device using uhci_hcd and
address 92
[ 395.121683] usb 2-2: device descriptor read/all, error -71
[ 395.176103] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 396.216038] usb 2-2: new full speed USB device using uhci_hcd and
address 94
[ 396.366761] usb 2-2: unable to read config index 0 descriptor/all
[ 396.366762] usb 2-2: can't read configurations, error -71
[ 396.424065] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 397.456073] usb 2-2: new full speed USB device using uhci_hcd and
address 96
[ 397.606587] usb 2-2: unable to read config index 0 descriptor/all
[ 397.606587] usb 2-2: can't read configurations, error -71
[ 397.664109] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 398.696080] usb 2-2: new full speed USB device using uhci_hcd and
address 98
[ 398.838747] usb 2-2: device descriptor read/all, error -71
[ 398.896068] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 399.936072] usb 2-2: new full speed USB device using uhci_hcd and
address 100
[ 400.085736] usb 2-2: unable to read config index 0 descriptor/start: -71
[ 400.085736] usb 2-2: chopping to 0 config(s)
[ 400.093874] usb 2-2: string descriptor 0 read error: -71
[ 400.101757] usb 2-2: string descriptor 0 read error: -71
[ 400.109490] usb 2-2: string descriptor 0 read error: -71
[ 400.109490] usb 2-2: no configuration chosen from 0 choices
[ 400.109490] usb 2-2: New USB device found, idVendor=04d8, idProduct=000a
[ 400.109490] usb 2-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[ 400.109490] usb 2-2: USB disconnect, address 100
[ 401.176045] usb 2-2: new full speed USB device using uhci_hcd and
address 101
[ 401.232064] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 402.416082] usb 2-2: new full speed USB device using uhci_hcd and
address 102
[ 402.472111] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 403.656082] usb 2-2: new full speed USB device using uhci_hcd and
address 103
[ 403.712103] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 404.896044] usb 2-2: new full speed USB device using uhci_hcd and
address 104
[ 404.952098] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 406.136072] usb 2-2: new full speed USB device using uhci_hcd and
address 105
[ 406.192107] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 407.376078] usb 2-2: new full speed USB device using uhci_hcd and
address 106
[ 407.432115] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 408.616099] usb 2-2: new full speed USB device using uhci_hcd and
address 107
[ 408.766762] usb 2-2: unable to read config index 0 descriptor/all
[ 408.766762] usb 2-2: can't read configurations, error -71
[ 408.824118] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 409.856084] usb 2-2: new full speed USB device using uhci_hcd and
address 109
[ 409.912132] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 411.096048] usb 2-2: new full speed USB device using uhci_hcd and
address 110
[ 411.245982] usb 2-2: unable to read config index 0 descriptor/all
[ 411.245982] usb 2-2: can't read configurations, error -71
[ 411.304077] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 412.336053] usb 2-2: new full speed USB device using uhci_hcd and
address 112
[ 412.392081] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 413.576055] usb 2-2: new full speed USB device using uhci_hcd and
address 113
[ 413.632078] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 414.816046] usb 2-2: new full speed USB device using uhci_hcd and
address 114
[ 414.872082] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 416.056052] usb 2-2: new full speed USB device using uhci_hcd and
address 115
[ 416.207055] usb 2-2: unable to read config index 0 descriptor/all
[ 416.207055] usb 2-2: can't read configurations, error -71
[ 416.264080] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 417.296046] usb 2-2: new full speed USB device using uhci_hcd and
address 117
[ 417.446150] usb 2-2: unable to read config index 0 descriptor/all
[ 417.446150] usb 2-2: can't read configurations, error -71
[ 417.504136] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 418.536048] usb 2-2: new full speed USB device using uhci_hcd and
address 119
[ 418.686768] usb 2-2: unable to read config index 0 descriptor/all
[ 418.686768] usb 2-2: can't read configurations, error -71
[ 418.744077] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 419.776055] usb 2-2: new full speed USB device using uhci_hcd and
address 121
[ 419.832073] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 421.016049] usb 2-2: new full speed USB device using uhci_hcd and
address 122
[ 421.072088] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 422.256049] usb 2-2: new full speed USB device using uhci_hcd and
address 123
[ 422.398770] usb 2-2: device descriptor read/all, error -71
[ 422.456076] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 423.496051] usb 2-2: new full speed USB device using uhci_hcd and
address 125
[ 423.646900] usb 2-2: unable to read config index 0 descriptor/all
[ 423.646914] usb 2-2: can't read configurations, error -71
[ 423.704075] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 424.736046] usb 2-2: new full speed USB device using uhci_hcd and
address 127
[ 424.886764] usb 2-2: unable to read config index 0 descriptor/all
[ 424.886778] usb 2-2: can't read configurations, error -71
[ 424.944071] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 425.976048] usb 2-2: new full speed USB device using uhci_hcd and
address 4
[ 426.121685] usb 2-2: device descriptor read/all, error -71
[ 426.176082] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 427.216049] usb 2-2: new full speed USB device using uhci_hcd and
address 6
[ 427.272083] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 428.456049] usb 2-2: new full speed USB device using uhci_hcd and
address 7
[ 428.512072] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 429.696049] usb 2-2: new full speed USB device using uhci_hcd and
address 8
[ 429.752079] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 430.936052] usb 2-2: new full speed USB device using uhci_hcd and
address 9
[ 431.086733] usb 2-2: unable to read config index 0 descriptor/all
[ 431.086733] usb 2-2: can't read configurations, error -71
[ 431.144075] hub 2-0:1.0: unable to enumerate USB device on port 2
[ 432.176055] usb 2-2: new full speed USB device using uhci_hcd and
address 11
[ 432.318826] usb 2-2: device descriptor read/all, error -71
[ 432.376080] hub 2-0:1.0: unable to enumerate USB device on port 2

lsmod -v:
Module Size Used by
wlan_ccmp 6496 2
i915 25280 2
drm 65256 3 i915
rfcomm 28272 0
l2cap 17248 5 rfcomm
bluetooth 44900 4 rfcomm,l2cap
ipv6 235300 14
ppdev 6468 0
parport_pc 22500 0
lp 8164 0
parport 30988 3 ppdev,parport_pc,lp
cpufreq_powersave 1856 0
cpufreq_stats 3776 0
cpufreq_userspace 3172 0
cpufreq_ondemand 6476 0
cpufreq_conservative 5960 0
freq_table 4224 2 cpufreq_stats,cpufreq_ondemand
cdc_acm 12224 0
pciehp 28540 0
pci_hotplug 23460 1 pciehp
wlan_scan_sta 11296 1
usbhid 35904 0
hid 33184 1 usbhid
ff_memless 4392 1 usbhid
uvcvideo 45704 0
compat_ioctl32 1312 1 uvcvideo
videodev 27520 1 uvcvideo
v4l1_compat 12260 2 uvcvideo,videodev
usb_storage 75936 0
serio_raw 4740 0
psmouse 32336 0
rng_core 3940 0
pcspkr 2432 0
i2c_i801 7920 0
snd_hda_intel 324248 1
i2c_core 19828 1 i2c_i801
snd_pcm_oss 32800 0
snd_pcm 62596 2 snd_hda_intel,snd_pcm_oss
iTCO_wdt 9508 0
snd_mixer_oss 12320 1 snd_pcm_oss
video 16432 0
output 2912 1 video
battery 10180 0
snd_seq_dummy 2660 0
ac 4196 0
ath_rate_sample 11104 1
ath_pci 202712 0
eeepc_laptop 7440 0
button 6096 0
wlan 194000 5
wlan_ccmp,wlan_scan_sta,ath_rate_sample,ath_pci
ath_hal 300768 3 ath_rate_sample,ath_pci
atl2 22744 0
snd_seq_oss 24992 0
snd_seq_midi_event 6432 1 snd_seq_oss
snd_seq 41456 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_timer 17800 2 snd_pcm,snd_seq
snd_seq_device 6380 3 snd_seq_dummy,snd_seq_oss,snd_seq
snd 45604 10
snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,sn d_seq_oss,snd_seq,snd_timer,snd_seq_device
intel_agp 22332 1
agpgart 28776 3 drm,intel_agp
soundcore 6368 1 snd
snd_page_alloc 7816 2 snd_hda_intel,snd_pcm
evdev 8000 6
ext3 105512 1
jbd 39444 1 ext3
mbcache 7108 1 ext3
sd_mod 22200 3
ide_pci_generic 3908 0 [permanent]
ide_core 96168 1 ide_pci_generic
ata_generic 4676 0
ata_piix 14180 2
ahci 23176 0
libata 140384 3 ata_generic,ata_piix,ahci
scsi_mod 129356 3 usb_storage,sd_mod,libata
dock 8304 1 libata
ehci_hcd 28428 0
uhci_hcd 18672 0
usbcore 118160 7
cdc_acm,usbhid,uvcvideo,usb_storage,ehci_hcd,uhci_ hcd
thermal 15228 0
processor 32576 2 thermal
fan 4164 0
thermal_sys 10856 4 video,thermal,processor,fan

lspci:
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express
Processor to DRAM Controller (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 82d9
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information <?>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp

00:02.0 VGA compatible controller: Intel Corporation Mobile
915GM/GMS/910GML Express Graphics Controller (rev 04) (prog-if 00 [VGA
controller])
Subsystem: ASUSTeK Computer Inc. Device 82d9
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f7f00000 (32-bit, non-prefetchable) [size=512K]
I/O ports at ec00 [size=8]
Memory at d0000000 (32-bit, prefetchable) [size=256M]
Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Kernel modules: intelfb

00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML
Express Graphics Controller (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 82d9
Flags: bus master, fast devsel, latency 0
Memory at f7f80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 2

00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) High Definition Audio Controller (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 8337
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
PCI Express Port 1 (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
PCI Express Port 2 (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: fbf00000-fbffffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.2 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family)
PCI Express Port 3 (rev 04) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
Memory behind bridge: f8000000-fbefffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable+
Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device 82d8
Capabilities: [a0] Power Management version 2
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #1 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, medium devsel, latency 0, IRQ 23
I/O ports at e400 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #2 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, medium devsel, latency 0, IRQ 19
I/O ports at e480 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #3 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, medium devsel, latency 0, IRQ 18
I/O ports at e800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB UHCI #4 (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, medium devsel, latency 0, IRQ 16
I/O ports at e880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6
Family) USB2 EHCI Controller (rev 04) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
(prog-if 01 [Subtractive decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device 82d8

00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface
Bridge (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, medium devsel, latency 0
Kernel modules: intel-rng, iTCO_wdt

00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller
(rev 04) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at ffa0 [size=16]
Capabilities: [70] Power Management version 2
Kernel driver in use: ata_piix
Kernel modules: ahci, ata_piix

00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus
Controller (rev 04)
Subsystem: ASUSTeK Computer Inc. Device 82d8
Flags: medium devsel, IRQ 19
I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg
Wireless PCI Express Adapter (rev 01)
Subsystem: Device 1a3b:1026
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at fbef0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Capabilities: [60] Express Legacy Endpoint, MSI 00
Capabilities: [90] MSI-X: Enable- Mask- TabSize=1
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Kernel driver in use: ath_pci
Kernel modules: ath_pci, ath5k

03:00.0 Ethernet controller: Attansic Technology Corp. L2 100 Mbit
Ethernet Adapter (rev a0)
Subsystem: ASUSTeK Computer Inc. Device 8233
Flags: bus master, fast devsel, latency 0, IRQ 220
Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fbfa0000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable+
Capabilities: [58] Express Endpoint, MSI 00
Capabilities: [6c] Vital Product Data <?>
Capabilities: [100] Advanced Error Reporting <?>
Kernel driver in use: atl2
Kernel modules: atl2


Any suggestion is very welcome.
Thanks.
Wim


--
To UNSUBSCRIBE, email to debian-user-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 

Thread Tools




All times are GMT. The time now is 05:10 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright ©2007 - 2008, www.linux-archive.org