FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 05-26-2008, 10:07 AM
Martin Unzner
 
Default Bug#482972: linux-image-2.6.24-1-amd64: 10 in 1 USB card reader doesn't work

Package: linux-image-2.6.24-1-amd64
Version: 2.6.24-7
Severity: normal

Hello guys,

this bug has been reported earlier by me, but now I'm running
Debian Lenny with a recent kernel, and the problem is still the same: My
10 in 1 USB Card Reader doesn't work with Debian. Whenever I plug my 2
GB SD Card on other computers or on another system supplied with my
computer, it works perfectly, but in Debian, I can't see more than the
file structure, reading from and writing to the card is impossible. I
suppose the reason lies within these lines that dmesg outputs when I
plug
the card reader:

usb 6-1: new high speed USB device using ehci_hcd and address 5
usb 6-1: configuration #1 chosen from 1 choice
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 6:0:0:0: Direct-Access GENERIC USB Storage-CFC I19B PQ: 0
ANSI: 0 CCS
scsi 6:0:0:1: Direct-Access GENERIC USB Storage-MSC I19B PQ: 0
ANSI: 0 CCS
scsi 6:0:0:2: Direct-Access GENERIC USB Storage-SMC I19B PQ: 0
ANSI: 0 CCS
scsi 6:0:0:3: Direct-Access GENERIC USB Storage-SDC I19B PQ: 0
ANSI: 0 CCS
sd 6:0:0:0: [sdb] Attached SCSI removable disk
sd 6:0:0:1: [sdc] Attached SCSI removable disk
sd 6:0:0:2: [sdd] Attached SCSI removable disk
sd 6:0:0:3: [sde] 2011136 512-byte hardware sectors (1030 MB)
sd 6:0:0:3: [sde] Write Protect is off
sd 6:0:0:3: [sde] Mode Sense: 03 00 00 00
sd 6:0:0:3: [sde] Assuming drive cache: write through
sd 6:0:0:3: [sde] 2011136 512-byte hardware sectors (1030 MB)
sd 6:0:0:3: [sde] Write Protect is off
sd 6:0:0:3: [sde] Mode Sense: 03 00 00 00
sd 6:0:0:3: [sde] Assuming drive cache: write through
sde: sde1
sde: p1 exceeds device capacity
sd 6:0:0:3: [sde] Attached SCSI removable disk
attempt to access beyond end of device
sde: rw=0, want=4022132, limit=2011136
printk: 167 messages suppressed.
Buffer I/O error on device sde1, logical block 4021888
attempt to access beyond end of device
sde: rw=0, want=4022133, limit=2011136
Buffer I/O error on device sde1, logical block 4021889
....

1030 MB is definitely not correct. I'm not a USB expert, but maybe the
hardware sector size is not 512 Bytes but 1024? Just a suggestion, but
something definitely goes wrong in the usb-storage module. usbview shows
the following information about the card reader:

USB Storage Device
Manufacturer: GENERIC
Serial Number: 200501041423444LD
Speed: 480Mb/s (high)
USB Version: 2.00
Device Class: 00(>ifc )
Device Subclass: 00
Device Protocol: 00
Maximum Default Endpoint Size: 64
Number of Configurations: 1
Vendor Id: 0aec
Product Id: 3260
Revision Number: 2.0a

Config Number: 1
Number of Interfaces: 1
Attributes: 80
MaxPower Needed: 500mA

Interface Number: 0
Name: usb-storage
Alternate Number: 0
Class: 08(stor.)
Sub Class: 06
Protocol: 50
Number of Endpoints: 2

Endpoint Address: 01
Direction: out
Attribute: 2
Type: Bulk
Max Packet Size: 512
Interval: 0ms

Endpoint Address: 82
Direction: in
Attribute: 2
Type: Bulk
Max Packet Size: 512
Interval: 0ms

I hope I have supplied enough information for you to fix the bug. Thanks
a lot!

Martin

-- Package-specific info:
** Version:
Linux version 2.6.24-1-amd64 (Debian 2.6.24-7) (dannf@debian.org) (gcc version 4.1.3 20080114 (prerelease) (Debian 4.1.2-19)) #1 SMP Sat May 10 09:28:10 UTC 2008

** Command line:
root=/dev/sda9 ro quiet

** Not tainted

** Kernel log:
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022268, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022268, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022268, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022268, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022204, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022205, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022206, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022207, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022208, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022209, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022210, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022211, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022260, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022261, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022262, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022263, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022264, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022265, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022266, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022267, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022268, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022268, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022269, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022270, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022271, limit=2011136
attempt to access beyond end of device
sde: rw=0, want=4022272, limit=2011136
usb 6-1: USB disconnect, address 6

** Loaded modules:
Module Size Used by
nls_iso8859_1 9728 0
nls_cp437 11392 0
vfat 17920 0
fat 58288 1 vfat
usb_storage 92096 0
radeon 123552 0
drm 98856 1 radeon
ipv6 286248 23
ppdev 13832 0
parport_pc 42408 0
lp 17476 0
parport 44812 3 ppdev,parport_pc,lp
powernow_k8 18464 1
cpufreq_userspace 9604 0
cpufreq_ondemand 13712 1
cpufreq_conservative 13320 0
cpufreq_powersave 6272 0
cpufreq_stats 10528 0
freq_table 9728 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
fuse 53680 2
loop 22788 0
joydev 17536 0
snd_hda_intel 362152 3
snd_pcm_oss 46624 0
snd_pcm 89352 3 snd_hda_intel,snd_pcm_oss
snd_mixer_oss 21376 1 snd_pcm_oss
snd_seq_dummy 8580 0
pcmcia 45720 0
firmware_class 15104 1 pcmcia
snd_seq_oss 36736 0
snd_seq_midi 13376 0
snd_rawmidi 30624 1 snd_seq_midi
snd_seq_midi_event 12544 2 snd_seq_oss,snd_seq_midi
snd_seq 58752 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
snd_timer 28552 3 snd_pcm,snd_seq
snd_seq_device 12948 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
psmouse 45724 0
snd 65896 13 snd_hda_intel,snd_pcm_oss,snd_pcm,snd_mixer_oss,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
pcspkr 7808 0
i2c_piix4 13708 0
yenta_socket 31756 1
rsrc_nonstatic 16128 1 yenta_socket
pcmcia_core 46500 3 pcmcia,yenta_socket,rsrc_nonstatic
k8temp 10496 0
serio_raw 11908 0
soundcore 13216 1 snd
i2c_core 29824 1 i2c_piix4
snd_page_alloc 15248 2 snd_hda_intel,snd_pcm
video 25620 0
container 9856 0
output 8704 1 video
battery 19976 0
ac 11400 0
button 13984 0
shpchp 38428 0
pci_hotplug 35504 1 shpchp
evdev 17024 7
ext3 139024 4
jbd 55976 1 ext3
mbcache 13952 1 ext3
ide_cd 44704 0
cdrom 39464 1 ide_cd
ata_generic 13060 0
generic 9732 0 [permanent]
sd_mod 33536 7
usbhid 35168 0
hid 41792 1 usbhid
ehci_hcd 39692 0
atiixp 9488 0 [permanent]
ide_core 144920 3 ide_cd,generic,atiixp
ahci 34564 6
ohci_hcd 28164 0
libata 162992 2 ata_generic,ahci
scsi_mod 170296 3 usb_storage,sd_mod,libata
tg3 100612 0
thermal 22688 0
processor 45032 2 powernow_k8,thermal
fan 9864 0

** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS690 Host Bridge [1002:7910]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64

00:01.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) [1002:7912]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0200000-d03fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000c7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp

00:04.0 PCI bridge [0604]: ATI Technologies Inc Device [1002:7914]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=10, subordinate=10, sec-latency=0
Memory behind bridge: d0000000-d00fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:05.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 1) [1002:7915]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: cc000000-cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:06.0 PCI bridge [0604]: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) [1002:7916]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=30, subordinate=30, sec-latency=0
Memory behind bridge: c8000000-c80fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:12.0 SATA controller [0106]: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380] (prog-if 01)
Subsystem: ATI Technologies Inc SB600 Non-Raid-5 SATA [1002:4380]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9000 [size=8]
Region 1: I/O ports at 9008 [size=4]
Region 2: I/O ports at 9010 [size=8]
Region 3: I/O ports at 5018 [size=4]
Region 4: I/O ports at 5020 [size=16]
Region 5: Memory at d0409000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

00:13.0 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI0) [1002:4387] (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d0401000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.1 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI1) [1002:4388] (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d0402000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.2 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI2) [1002:4389] (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at d0403000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.3 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI3) [1002:438a] (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at d0404000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.4 USB Controller [0c03]: ATI Technologies Inc SB600 USB (OHCI4) [1002:438b] (prog-if 10)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at d0405000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.5 USB Controller [0c03]: ATI Technologies Inc SB600 USB Controller (EHCI) [1002:4386] (prog-if 20)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 23
Region 0: Memory at d0406000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 14)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 8200 [size=16]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4

00:14.1 IDE interface [0101]: ATI Technologies Inc SB600 IDE [1002:438c] (prog-if 82 [Master PriP])
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 5040 [size=16]
Kernel driver in use: ATIIXP_IDE
Kernel modules: ata_generic, atiixp, generic

00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia [1002:4383]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at 88000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:14.3 ISA bridge [0601]: ATI Technologies Inc SB600 PCI to LPC Bridge [1002:438d]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=02, subordinate=06, sec-latency=64
Memory behind bridge: d0100000-d01fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS690M [Radeon X1200 Series] [1002:791f]
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 11
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=128M]
Region 2: Memory at d0200000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 4000 [size=256]
Region 5: Memory at d0300000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>

02:04.0 CardBus bridge [0607]: Ricoh Co Ltd RL5c476 II [1180:0476] (rev b6)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d0100000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 8c000000-8ffff000 (prefetchable)
Memory window 1: 90000000-93fff000
I/O window 0: 00001000-000010ff
I/O window 1: 00001400-000014ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket

10:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express [14e4:1713] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:30c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1276
Region 0: Memory at d0000000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3



-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.24-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.24-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92a tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo

linux-image-2.6.24-1-amd64 recommends no packages.

-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-1-amd64/preinst/abort-overwrite-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-dir-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/failed-to-move-modules-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/bootloader-test-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/preinst/lilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/create-kimage-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-initrd-2.6.24-1-amd64: false
linux-image-2.6.24-1-amd64/postinst/old-system-map-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.24-1-amd64/preinst/overwriting-modules-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/bootloader-error-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/preinst/abort-install-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/postinst/old-initrd-link-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.24-1-amd64/preinst/bootloader-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/prerm/would-invalidate-boot-loader-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/initrd-2.6.24-1-amd64:
linux-image-2.6.24-1-amd64/prerm/removing-running-kernel-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/preinst/elilo-initrd-2.6.24-1-amd64: true
linux-image-2.6.24-1-amd64/postinst/depmod-error-2.6.24-1-amd64: false



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 
Old 05-26-2008, 11:49 AM
maximilian attems
 
Default Bug#482972: linux-image-2.6.24-1-amd64: 10 in 1 USB card reader doesn't work

On Mon, May 26, 2008 at 12:07:09PM +0200, Martin Unzner wrote:
> Package: linux-image-2.6.24-1-amd64
> Version: 2.6.24-7
> Severity: normal

please try out 2.6.25 from unstable just installs fine in testing.

> Hello guys,
>
> this bug has been reported earlier by me, but now I'm running
> Debian Lenny with a recent kernel, and the problem is still the same:

care to name the bug nr?

> My
> 10 in 1 USB Card Reader doesn't work with Debian. Whenever I plug my 2
> GB SD Card on other computers or on another system supplied with my
> computer, it works perfectly, but in Debian, I can't see more than the
> file structure, reading from and writing to the card is impossible. I
> suppose the reason lies within these lines that dmesg outputs when I
> plug
> the card reader:
>
> usb 6-1: new high speed USB device using ehci_hcd and address 5
> usb 6-1: configuration #1 chosen from 1 choice
> scsi6 : SCSI emulation for USB Mass Storage devices
> usb-storage: device found at 5
> usb-storage: waiting for device to settle before scanning
> usb-storage: device scan complete
> scsi 6:0:0:0: Direct-Access GENERIC USB Storage-CFC I19B PQ: 0
> ANSI: 0 CCS
> scsi 6:0:0:1: Direct-Access GENERIC USB Storage-MSC I19B PQ: 0
> ANSI: 0 CCS
> scsi 6:0:0:2: Direct-Access GENERIC USB Storage-SMC I19B PQ: 0
> ANSI: 0 CCS
> scsi 6:0:0:3: Direct-Access GENERIC USB Storage-SDC I19B PQ: 0
> ANSI: 0 CCS
> sd 6:0:0:0: [sdb] Attached SCSI removable disk
> sd 6:0:0:1: [sdc] Attached SCSI removable disk
> sd 6:0:0:2: [sdd] Attached SCSI removable disk
> sd 6:0:0:3: [sde] 2011136 512-byte hardware sectors (1030 MB)
> sd 6:0:0:3: [sde] Write Protect is off
> sd 6:0:0:3: [sde] Mode Sense: 03 00 00 00
> sd 6:0:0:3: [sde] Assuming drive cache: write through
> sd 6:0:0:3: [sde] 2011136 512-byte hardware sectors (1030 MB)
> sd 6:0:0:3: [sde] Write Protect is off
> sd 6:0:0:3: [sde] Mode Sense: 03 00 00 00
> sd 6:0:0:3: [sde] Assuming drive cache: write through
> sde: sde1
> sde: p1 exceeds device capacity
> sd 6:0:0:3: [sde] Attached SCSI removable disk
> attempt to access beyond end of device
> sde: rw=0, want=4022132, limit=2011136
> printk: 167 messages suppressed.
> Buffer I/O error on device sde1, logical block 4021888
> attempt to access beyond end of device
> sde: rw=0, want=4022133, limit=2011136
> Buffer I/O error on device sde1, logical block 4021889
> ....
>
> 1030 MB is definitely not correct. I'm not a USB expert, but maybe the
> hardware sector size is not 512 Bytes but 1024? Just a suggestion, but
> something definitely goes wrong in the usb-storage module. usbview shows
> the following information about the card reader:

--
maks



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 
Old 05-26-2008, 02:11 PM
maximilian attems
 
Default Bug#482972: linux-image-2.6.24-1-amd64: 10 in 1 USB card reader doesn't work

hello martin,

[please keep bug report on cc, thanks ]

On Mon, May 26, 2008 at 03:52:53PM +0200, Martin Unzner wrote:
> Hi Maximilian,
>
> I just tried kernel 2.6.25, and the problem is still the same. Actually I'm not very keen on making one, but do you think a self-compiled kernel could/would do any better here?
> My previous report was bug #469717 and has meanwhile been closed.
>
> Thanks!
>
> Martin

i've newer for you to test:
http://photon.itp.tuwien.ac.at/~mattems/

this is allmost latest linus, just running fine here on my x61s
how is it doing?

--
maks



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 

Thread Tools




All times are GMT. The time now is 12:28 AM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org