FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 10-02-2012, 02:28 PM
David Smith
 
Default Bug#684352: phy0/hp-wifi problems after kernel update from 2.6 to 3.2

Hello, I'm having a problem with my Intel 2200 wireless on my Compaq Presario V4000T (made by HP) that has started happening after I upgraded my kernel from 2.6 to 3.2.

Problem: phy0 wireless state is incorrect.


Steps to reproduce problem:
1. Upgrade kernel from 2.6 to 3.2
2. rfkill now reports that I have two wireless devices but I only have the Intel 2200 wireless:

*Miho:/home/david# rfkill list all
*0: hp-wifi: Wireless LAN

******** Soft blocked: yes
******** Hard blocked: no
*1: phy0: Wireless LAN
******** Soft blocked: yes
******** Hard blocked: yes

3.* The wireless simply doesn't work anymore because all software believes the wireless is blocked with a hardware switch, which is not the case.


After many many hours of searching, I discovered that running "rfkill unblock all" is able to remove the "Hard Block" from phy0 and put the wireless into this state:


Miho:/home/david# rfkill unblock all

Miho:/home/david# rfkill list all
0: hp-wifi: Wireless LAN
******* Soft blocked: no
******* Hard blocked: no
1: phy0: Wireless LAN
******* Soft blocked: no
******* Hard blocked: no
Miho:/home/david#



However, I find that I have to keep dropping to a console and running "sudo rfkill unblock all" because the hardware keeps going back into the first state where phy0 is reporting that it is hard blocked, when it really isn't.




Workaround #1: Set "ACPI=off" on 3.2 kernel. After which, the wireless appears to be correctly reported:
Miho:/home/david# rfkill list all
0: phy0: Wireless LAN
******* Soft blocked: no
******* Hard blocked: no


This causes phy0 to accurately reflect the state of the hardware.

Workaround #2: Add hp-wmi to modprobe blacklist.* Again, this causes only phy0 wireless to be reported and phy0 always accurately reflects the state of the hardware (both soft and hard blocked).


Expected Results;
Both phy0 and hp-wifi refer to the same hardware device so they should accurately report the correct state of that hardware device.

Actual Results:
Phy0 reports it is hard blocked when there is no hard block on the wireless.* Further, phy0 keeps going into this "hard blocked" state from regular usage of the wireless with networkmanager, while the hp-wmi does not.* If I remove the hp-wmi then the phy0 works properly.* When I have hp-wmi, then phy0's state is often incorrect.* It seems there may be some conflict here between phy0 and hp-wmi.



**
Kernel versions tested:
linux-image-3.2.0-3-686-pae: Wireless regularly gets into this "bad state" of reporting it's hard blocked when it isn't. Unable to recover from it without using "sudo rfkill unblock all".


linux-image-2.6.32-5-686: No problem at all
*

*PCI registers from the only wireless device I have in this PC:
*
*Miho:/home/david# lspci -vv -s06:05.0
06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)

******* Subsystem: Hewlett-Packard Company Device 12f5
******* Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
******* Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

******* Latency: 128 (750ns min, 6000ns max), Cache Line Size: 32 bytes
******* Interrupt: pin A routed to IRQ 20
******* Region 0: Memory at c8206000 (32-bit, non-prefetchable) [size=4K]
******* Capabilities: [dc] Power Management version 2

*************** Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
*************** Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
******* Kernel driver in use: ipw2200

Miho:/home/david#



Somehow network manager is putting phy0 into a "hard blocked" state, but the hardware is not really hardblocked. After going into this hard blocked state, the wireless cannot be used anymore unless dropping to a console and running sudo rfkill unblock all which removes the "hard block" from phy0. Networkmanager alone is not able to bring the wireless back up.


Also, sometimes when I turn on the PC, or resume from hibernate the rfkill reports phy0 as hard blocked, when it isn't. Which again, forces me to drop to console and run a "sudo rfkill unblock all"


I am currently using Workaround #2 and am very happy with it. The wireless no longer goes into "hard blocked" through normal usage of the hardware with network manager.

Thank you for your time.






[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-3-686-pae (Debian 3.2.21-3) (
debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-8) ) #1
SMP Thu Jun 28 08:56:46 UTC 2012
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007feeb000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007feeb000 - 000000007ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] DMI: Hewlett-Packard Pavilion dv4000 (x123xx#ABA)/309E, BIOS
F.15 05/24/2006
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000
(usable)
[ 0.000000] last_pfn = 0x7fee0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E3FFF uncachable
[ 0.000000] E4000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] PAT not supported by CPU.
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[ 0.000000] RAMDISK: 36714000 - 37382000
[ 0.000000] ACPI: RSDP 000f76a0 00014 (v00 HP )
[ 0.000000] ACPI: RSDT 7fee51c1 00044 (v01 HP 309E 06040000 LTP
00000000)
[ 0.000000] ACPI: FACP 7feeae88 00074 (v01 HP 309E 06040000 LOHR
0000005F)
[ 0.000000] ACPI: DSDT 7fee5a66 05422 (v01 HP 309E 06040000 MSFT
0100000E)
[ 0.000000] ACPI: FACS 7fefbfc0 00040
[ 0.000000] ACPI: APIC 7feeaefc 00068 (v01 HP 309E 06040000 LOHR
0000005F)
[ 0.000000] ACPI: BOOT 7feeafd8 00028 (v01 HP 309E 06040000 LTP
00000001)
[ 0.000000] ACPI: MCFG 7feeaf9c 0003C (v01 HP 309E 06040000 LOHR
0000005F)
[ 0.000000] ACPI: SSDT 7fee561d 00277 (v01 HP 309E 00003000 INTL
20030224)
[ 0.000000] ACPI: SSDT 7fee5445 001D8 (v01 HP 309E 00003001 INTL
20030224)
[ 0.000000] ACPI: SSDT 7fee5331 00114 (v01 HP 309E 00003000 INTL
20030224)
[ 0.000000] ACPI: SSDT 7fee5205 0012C (v01 HP 309E 00000001 INTL
20030224)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1156MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0007fee0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fee0
[ 0.000000] On node 0 totalpages: 523887
[ 0.000000] free_area_init_node: node 0, pgdat c140d640, node_mem_map
f5714200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2314 pages used for memmap
[ 0.000000] HighMem zone: 293848 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 -
0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2
nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f79d5000 s33280 r0 d24064
u57344
[ 0.000000] pcpu-alloc: s33280 r0 d24064 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 519793
[ 0.000000] Kernel command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-3-686-pae
root=UUID=7397b469-cdfc-4e8a-ae54-294d980fefb4 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000379fe:0007fee0)
[ 0.000000] Memory: 2060268k/2096000k available (2836k kernel code,
35280k reserved, 1343k data, 412k init, 1184648k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc1415000 - 0xc147c000 ( 412 kB)
[ 0.000000] .data : 0xc12c50ec - 0xc1414f00 (1343 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12c50ec (2836 kB)
[ 0.000000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f7406000 soft=f7408000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1995.689 MHz processor.
[ 0.008003] Calibrating delay loop (skipped), value calculated using
timer frequency.. 3991.37 BogoMIPS (lpj=7982756)
[ 0.008009] pid_max: default: 32768 minimum: 301
[ 0.008058] Security Framework initialized
[ 0.008068] AppArmor: AppArmor disabled by boot time parameter
[ 0.008087] Mount-cache hash table entries: 512
[ 0.008250] Initializing cgroup subsys cpuacct
[ 0.008257] Initializing cgroup subsys memory
[ 0.008268] Initializing cgroup subsys devices
[ 0.008271] Initializing cgroup subsys freezer
[ 0.008273] Initializing cgroup subsys net_cls
[ 0.008276] Initializing cgroup subsys blkio
[ 0.008284] Initializing cgroup subsys perf_event
[ 0.008316] Disabled fast string operations
[ 0.008326] mce: CPU supports 5 MCE banks
[ 0.008337] CPU0: Thermal monitoring enabled (TM2)
[ 0.008401] SMP alternatives: switching to UP code
[ 0.011453] ACPI: Core revision 20110623
[ 0.016071] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.016515] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.057014] CPU0: Intel(R) Pentium(R) M processor 2.00GHz stepping 08
[ 0.060003] Performance Events: p6 PMU driver.
[ 0.060003] ... version: 0
[ 0.060003] ... bit width: 32
[ 0.060003] ... generic registers: 2
[ 0.060003] ... value mask: 00000000ffffffff
[ 0.060003] ... max period: 000000007fffffff
[ 0.060003] ... fixed-purpose events: 0
[ 0.060003] ... event mask: 0000000000000003
[ 0.060003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.060003] Brought up 1 CPUs
[ 0.060003] Total of 1 processors activated (3991.37 BogoMIPS).
[ 0.060003] devtmpfs: initialized
[ 0.060003] PM: Registering ACPI NVS region at 7feeb000 (86016 bytes)
[ 0.060003] print_constraints: dummy:
[ 0.060003] NET: Registered protocol family 16
[ 0.060003] ACPI: bus type pci registered
[ 0.060003] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem
0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.060003] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.060003] PCI: Using MMCONFIG for extended config space
[ 0.060003] PCI: Using configuration type 1 for base access
[ 0.060003] bio: create slab <bio-0> at 0
[ 0.060003] ACPI: Added _OSI(Module Device)
[ 0.060003] ACPI: Added _OSI(Processor Device)
[ 0.060003] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.060003] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.060017] ACPI: EC: Look up EC in DSDT
[ 0.061985] ACPI: Interpreter enabled
[ 0.061998] ACPI: (supports S0 S3 S4 S5)
[ 0.062020] ACPI: Using IOAPIC for interrupt routing
[ 0.068551] ACPI: EC: GPE = 0x1b, I/O: command/status = 0x66, data = 0x62
[ 0.068666] ACPI: No dock devices found.
[ 0.068668] HEST: Table not found.
[ 0.068674] PCI: Ignoring host bridge windows from ACPI; if necessary,
use "pci=use_crs" and report a bug
[ 0.069017] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.069702] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
(ignored)
[ 0.069706] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
(ignored)
[ 0.069709] pci_root PNP0A08:00: host bridge window [mem
0x000a0000-0x000bffff] (ignored)
[ 0.069713] pci_root PNP0A08:00: host bridge window [mem
0x000d0000-0x000d3fff] (ignored)
[ 0.069716] pci_root PNP0A08:00: host bridge window [mem
0x000d4000-0x000d7fff] (ignored)
[ 0.069719] pci_root PNP0A08:00: host bridge window [mem
0x000d8000-0x000dbfff] (ignored)
[ 0.069723] pci_root PNP0A08:00: host bridge window [mem
0x80000000-0xfebfffff] (ignored)
[ 0.069735] pci 0000:00:00.0: [8086:2590] type 0 class 0x000600
[ 0.069780] pci 0000:00:01.0: [8086:2591] type 1 class 0x000604
[ 0.069820] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.069824] pci 0000:00:01.0: PME# disabled
[ 0.069879] pci 0000:00:1c.0: [8086:2660] type 1 class 0x000604
[ 0.069979] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.069985] pci 0000:00:1c.0: PME# disabled
[ 0.070019] pci 0000:00:1d.0: [8086:2658] type 0 class 0x000c03
[ 0.070072] pci 0000:00:1d.0: reg 20: [io 0x1800-0x181f]
[ 0.070112] pci 0000:00:1d.1: [8086:2659] type 0 class 0x000c03
[ 0.072010] pci 0000:00:1d.1: reg 20: [io 0x1820-0x183f]
[ 0.072050] pci 0000:00:1d.2: [8086:265a] type 0 class 0x000c03
[ 0.072103] pci 0000:00:1d.2: reg 20: [io 0x1840-0x185f]
[ 0.072144] pci 0000:00:1d.3: [8086:265b] type 0 class 0x000c03
[ 0.072197] pci 0000:00:1d.3: reg 20: [io 0x1860-0x187f]
[ 0.072247] pci 0000:00:1d.7: [8086:265c] type 0 class 0x000c03
[ 0.072270] pci 0000:00:1d.7: reg 10: [mem 0xc8000000-0xc80003ff]
[ 0.072368] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.072373] pci 0000:00:1d.7: PME# disabled
[ 0.072396] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.072483] pci 0000:00:1e.2: [8086:266e] type 0 class 0x000401
[ 0.072503] pci 0000:00:1e.2: reg 10: [io 0x1c00-0x1cff]
[ 0.072515] pci 0000:00:1e.2: reg 14: [io 0x1880-0x18bf]
[ 0.072527] pci 0000:00:1e.2: reg 18: [mem 0xc8000800-0xc80009ff]
[ 0.072538] pci 0000:00:1e.2: reg 1c: [mem 0xc8000400-0xc80004ff]
[ 0.072597] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[ 0.072602] pci 0000:00:1e.2: PME# disabled
[ 0.072622] pci 0000:00:1e.3: [8086:266d] type 0 class 0x000703
[ 0.072642] pci 0000:00:1e.3: reg 10: [io 0x2400-0x24ff]
[ 0.072654] pci 0000:00:1e.3: reg 14: [io 0x2000-0x207f]
[ 0.072730] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold
[ 0.072735] pci 0000:00:1e.3: PME# disabled
[ 0.072757] pci 0000:00:1f.0: [8086:2641] type 0 class 0x000601
[ 0.072860] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.072869] pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6
ACPI/GPIO/TCO
[ 0.072876] pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6
GPIO
[ 0.072901] pci 0000:00:1f.1: [8086:266f] type 0 class 0x000101
[ 0.072918] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.072929] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.072941] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.072953] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.072964] pci 0000:00:1f.1: reg 20: [io 0x18c0-0x18cf]
[ 0.073009] pci 0000:00:1f.3: [8086:266a] type 0 class 0x000c05
[ 0.073078] pci 0000:00:1f.3: reg 20: [io 0x18e0-0x18ff]
[ 0.073159] pci 0000:01:00.0: [1002:5653] type 0 class 0x000300
[ 0.073170] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xd7ffffff pref]
[ 0.073178] pci 0000:01:00.0: reg 14: [io 0x3000-0x30ff]
[ 0.073186] pci 0000:01:00.0: reg 18: [mem 0xc8100000-0xc810ffff]
[ 0.073210] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.073239] pci 0000:01:00.0: supports D1 D2
[ 0.073249] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.
You can enable it with 'pcie_aspm=force'
[ 0.073258] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.073262] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 0.073265] pci 0000:00:01.0: bridge window [mem 0xc8100000-0xc81fffff]
[ 0.073269] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xd7ffffff
pref]
[ 0.073325] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.073391] pci 0000:06:05.0: [8086:4220] type 0 class 0x000280
[ 0.073419] pci 0000:06:05.0: reg 10: [mem 0xc8206000-0xc8206fff]
[ 0.073545] pci 0000:06:05.0: PME# supported from D0 D3hot D3cold
[ 0.073551] pci 0000:06:05.0: PME# disabled
[ 0.073577] pci 0000:06:06.0: [104c:8031] type 2 class 0x000607
[ 0.073606] pci 0000:06:06.0: reg 10: [mem 0xc8207000-0xc8207fff]
[ 0.073649] pci 0000:06:06.0: supports D1 D2
[ 0.073652] pci 0000:06:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.073658] pci 0000:06:06.0: PME# disabled
[ 0.073686] pci 0000:06:06.2: [104c:8032] type 0 class 0x000c00
[ 0.073713] pci 0000:06:06.2: reg 10: [mem 0xc8208000-0xc82087ff]
[ 0.073731] pci 0000:06:06.2: reg 14: [mem 0xc8200000-0xc8203fff]
[ 0.073844] pci 0000:06:06.2: supports D1 D2
[ 0.073847] pci 0000:06:06.2: PME# supported from D0 D1 D2 D3hot
[ 0.073853] pci 0000:06:06.2: PME# disabled
[ 0.073879] pci 0000:06:06.3: [104c:8033] type 0 class 0x000180
[ 0.073906] pci 0000:06:06.3: reg 10: [mem 0xc8204000-0xc8205fff]
[ 0.074029] pci 0000:06:06.3: supports D1 D2
[ 0.074032] pci 0000:06:06.3: PME# supported from D0 D1 D2 D3hot
[ 0.074038] pci 0000:06:06.3: PME# disabled
[ 0.074063] pci 0000:06:06.4: [104c:8034] type 0 class 0x000805
[ 0.074090] pci 0000:06:06.4: reg 10: [mem 0xc8209000-0xc82090ff]
[ 0.074106] pci 0000:06:06.4: reg 14: [mem 0xc8208c00-0xc8208cff]
[ 0.074124] pci 0000:06:06.4: reg 18: [mem 0xc8208800-0xc82088ff]
[ 0.074221] pci 0000:06:06.4: supports D1 D2
[ 0.074223] pci 0000:06:06.4: PME# supported from D0 D1 D2 D3hot
[ 0.074230] pci 0000:06:06.4: PME# disabled
[ 0.074261] pci 0000:06:07.0: [10ec:8139] type 0 class 0x000200
[ 0.074289] pci 0000:06:07.0: reg 10: [io 0x4000-0x40ff]
[ 0.074305] pci 0000:06:07.0: reg 14: [mem 0xc8209400-0xc82094ff]
[ 0.074416] pci 0000:06:07.0: supports D1 D2
[ 0.074418] pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
[ 0.074425] pci 0000:06:07.0: PME# disabled
[ 0.074477] pci 0000:00:1e.0: PCI bridge to [bus 06-07] (subtractive
decode)
[ 0.074482] pci 0000:00:1e.0: bridge window [io 0x4000-0x4fff]
[ 0.074488] pci 0000:00:1e.0: bridge window [mem 0xc8200000-0xc82fffff]
[ 0.074496] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff]
(subtractive decode)
[ 0.074499] pci 0000:00:1e.0: bridge window [mem
0x00000000-0xffffffff] (subtractive decode)
[ 0.074554] pci_bus 0000:07: [bus 07-0a] partially hidden behind
transparent bridge 0000:06 [bus 06-07]
[ 0.074573] pci_bus 0000:00: on NUMA node 0
[ 0.074576] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.074709] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.074778] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.074861] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.074966] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.074970] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND),
returned control mask: 0x1d
[ 0.074972] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.077846] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14
15) *11
[ 0.077906] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14
15) *10
[ 0.077962] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14
15)
[ 0.078018] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14
15) *10
[ 0.078073] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14
15) *11
[ 0.078129] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14
15)
[ 0.078185] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14
15)
[ 0.078240] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14
15)
[ 0.078351] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.078356] vgaarb: loaded
[ 0.078358] vgaarb: bridge control possible 0000:01:00.0
[ 0.078398] PCI: Using ACPI for IRQ routing
[ 0.088176] PCI: pci_cache_line_size set to 64 bytes
[ 0.088267] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.088270] reserve RAM buffer: 000000007fee0000 - 000000007fffffff
[ 0.088501] hpet clockevent registered
[ 0.088506] HPET: 3 timers in total, 0 timers will be used for per-cpu
timer
[ 0.088513] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.088518] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.092041] Switching to clocksource hpet
[ 0.093903] pnp: PnP ACPI init
[ 0.093918] ACPI: bus type pnp registered
[ 0.094267] pnp 00:00: [bus 00-ff]
[ 0.094271] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.094274] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.094276] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.094279] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.094282] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.094285] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.094288] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.094291] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.094293] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.094296] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.094299] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.094302] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.094305] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.094308] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.094310] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.094313] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.094316] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.094319] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[ 0.094365] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03
(active)
[ 0.095322] pnp 00:01: [io 0x0000-0x001f]
[ 0.095325] pnp 00:01: [io 0x0081-0x0091]
[ 0.095327] pnp 00:01: [io 0x0093-0x009f]
[ 0.095330] pnp 00:01: [io 0x00c0-0x00df]
[ 0.095332] pnp 00:01: [dma 4]
[ 0.095370] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.095381] pnp 00:02: [mem 0xff800000-0xffffffff]
[ 0.095420] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.095457] pnp 00:03: [io 0x00f0]
[ 0.095467] pnp 00:03: [irq 13]
[ 0.095506] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.095520] pnp 00:04: [io 0x004e-0x004f]
[ 0.095522] pnp 00:04: [io 0x0061]
[ 0.095525] pnp 00:04: [io 0x0063]
[ 0.095527] pnp 00:04: [io 0x0065]
[ 0.095529] pnp 00:04: [io 0x0067]
[ 0.095531] pnp 00:04: [io 0x0080]
[ 0.095534] pnp 00:04: [io 0x0092]
[ 0.095536] pnp 00:04: [io 0x00b2-0x00b3]
[ 0.095538] pnp 00:04: [io 0x0200-0x020f]
[ 0.095541] pnp 00:04: [io 0x0800-0x080f]
[ 0.095543] pnp 00:04: [io 0x1000-0x107f]
[ 0.095546] pnp 00:04: [io 0x1180-0x11bf]
[ 0.095548] pnp 00:04: [mem 0xe0000000-0xefffffff]
[ 0.095551] pnp 00:04: [mem 0xf0000000-0xf0003fff]
[ 0.095554] pnp 00:04: [mem 0xf0004000-0xf0004fff]
[ 0.095556] pnp 00:04: [mem 0xf0005000-0xf0005fff]
[ 0.095559] pnp 00:04: [mem 0xf0008000-0xf000bfff]
[ 0.095561] pnp 00:04: [mem 0xfed20000-0xfed8ffff]
[ 0.095635] system 00:04: [io 0x0200-0x020f] has been reserved
[ 0.095639] system 00:04: [io 0x0800-0x080f] has been reserved
[ 0.095642] system 00:04: [io 0x1000-0x107f] has been reserved
[ 0.095646] system 00:04: [io 0x1180-0x11bf] has been reserved
[ 0.095650] system 00:04: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.095653] system 00:04: [mem 0xf0000000-0xf0003fff] has been reserved
[ 0.095657] system 00:04: [mem 0xf0004000-0xf0004fff] has been reserved
[ 0.095661] system 00:04: [mem 0xf0005000-0xf0005fff] has been reserved
[ 0.095665] system 00:04: [mem 0xf0008000-0xf000bfff] has been reserved
[ 0.095669] system 00:04: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.095672] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.095713] pnp 00:05: [io 0x0070-0x0077]
[ 0.095753] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.095767] pnp 00:06: [io 0x0060]
[ 0.095769] pnp 00:06: [io 0x0064]
[ 0.095775] pnp 00:06: [irq 1]
[ 0.095820] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.095833] pnp 00:07: [irq 12]
[ 0.095880] pnp 00:07: Plug and Play ACPI device, IDs AUI1501 PNP0f13
(active)
[ 0.095897] pnp: PnP ACPI: found 8 devices
[ 0.095899] ACPI: ACPI bus type pnp unregistered
[ 0.095902] PnPBIOS: Disabled by ACPI PNP
[ 0.132581] PCI: max bus depth: 2 pci_try_num: 3
[ 0.132623] pci 0000:00:1e.0: BAR 15: assigned [mem
0x80000000-0x83ffffff pref]
[ 0.132628] pci 0000:00:1c.0: BAR 14: assigned [mem
0x84000000-0x841fffff]
[ 0.132632] pci 0000:00:1c.0: BAR 15: assigned [mem
0x84200000-0x843fffff 64bit pref]
[ 0.132638] pci 0000:00:1c.0: BAR 13: assigned [io 0x5000-0x5fff]
[ 0.132642] pci 0000:01:00.0: BAR 6: assigned [mem 0xc8120000-0xc813ffff
pref]
[ 0.132646] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.132649] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 0.132653] pci 0000:00:01.0: bridge window [mem 0xc8100000-0xc81fffff]
[ 0.132657] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xd7ffffff
pref]
[ 0.132662] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.132666] pci 0000:00:1c.0: bridge window [io 0x5000-0x5fff]
[ 0.132673] pci 0000:00:1c.0: bridge window [mem 0x84000000-0x841fffff]
[ 0.132678] pci 0000:00:1c.0: bridge window [mem 0x84200000-0x843fffff
64bit pref]
[ 0.132690] pci 0000:06:06.0: BAR 16: assigned [mem
0x88000000-0x8bffffff]
[ 0.132694] pci 0000:06:06.0: BAR 15: assigned [mem
0x80000000-0x83ffffff pref]
[ 0.132697] pci 0000:06:06.0: BAR 14: assigned [io 0x4400-0x44ff]
[ 0.132701] pci 0000:06:06.0: BAR 13: assigned [io 0x4800-0x48ff]
[ 0.132704] pci 0000:06:06.0: CardBus bridge to [bus 07-0a]
[ 0.132706] pci 0000:06:06.0: bridge window [io 0x4800-0x48ff]
[ 0.132713] pci 0000:06:06.0: bridge window [io 0x4400-0x44ff]
[ 0.132720] pci 0000:06:06.0: bridge window [mem 0x80000000-0x83ffffff
pref]
[ 0.132726] pci 0000:06:06.0: bridge window [mem 0x88000000-0x8bffffff]
[ 0.132732] pci 0000:00:1e.0: PCI bridge to [bus 06-07]
[ 0.132736] pci 0000:00:1e.0: bridge window [io 0x4000-0x4fff]
[ 0.132743] pci 0000:00:1e.0: bridge window [mem 0xc8200000-0xc82fffff]
[ 0.132749] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x83ffffff
pref]
[ 0.132767] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.132771] pci 0000:00:01.0: setting latency timer to 64
[ 0.132778] pci 0000:00:1c.0: enabling device (0000 -> 0003)
[ 0.132785] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.132792] pci 0000:00:1c.0: setting latency timer to 64
[ 0.132800] pci 0000:00:1e.0: setting latency timer to 64
[ 0.132812] pci 0000:06:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 0.132819] pci 0000:06:06.0: setting latency timer to 64
[ 0.132824] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.132827] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.132830] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 0.132832] pci_bus 0000:01: resource 1 [mem 0xc8100000-0xc81fffff]
[ 0.132835] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xd7ffffff pref]
[ 0.132838] pci_bus 0000:02: resource 0 [io 0x5000-0x5fff]
[ 0.132841] pci_bus 0000:02: resource 1 [mem 0x84000000-0x841fffff]
[ 0.132844] pci_bus 0000:02: resource 2 [mem 0x84200000-0x843fffff 64bit
pref]
[ 0.132847] pci_bus 0000:06: resource 0 [io 0x4000-0x4fff]
[ 0.132850] pci_bus 0000:06: resource 1 [mem 0xc8200000-0xc82fffff]
[ 0.132853] pci_bus 0000:06: resource 2 [mem 0x80000000-0x83ffffff pref]
[ 0.132856] pci_bus 0000:06: resource 4 [io 0x0000-0xffff]
[ 0.132859] pci_bus 0000:06: resource 5 [mem 0x00000000-0xffffffff]
[ 0.132862] pci_bus 0000:07: resource 0 [io 0x4800-0x48ff]
[ 0.132865] pci_bus 0000:07: resource 1 [io 0x4400-0x44ff]
[ 0.132867] pci_bus 0000:07: resource 2 [mem 0x80000000-0x83ffffff pref]
[ 0.132870] pci_bus 0000:07: resource 3 [mem 0x88000000-0x8bffffff]
[ 0.132907] NET: Registered protocol family 2
[ 0.132979] IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.133214] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.134021] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.134594] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.134597] TCP reno registered
[ 0.134603] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.134623] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.134777] NET: Registered protocol family 1
[ 0.134832] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.134853] pci 0000:00:1d.0: PCI INT A disabled
[ 0.134866] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.134884] pci 0000:00:1d.1: PCI INT B disabled
[ 0.134895] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.134914] pci 0000:00:1d.2: PCI INT C disabled
[ 0.134922] pci 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.134940] pci 0000:00:1d.3: PCI INT D disabled
[ 0.134949] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.134981] pci 0000:00:1d.7: PCI INT A disabled
[ 0.135004] pci 0000:01:00.0: Boot video device
[ 0.135027] PCI: CLS 32 bytes, default 64
[ 0.135109] Unpacking initramfs...
[ 0.556802] Freeing initrd memory: 12728k freed
[ 0.567041] Simple Boot Flag at 0x36 set to 0x1
[ 0.567498] audit: initializing netlink socket (disabled)
[ 0.567516] type=2000 audit(1344849730.564:1): initialized
[ 0.592710] highmem bounce pool size: 64 pages
[ 0.592717] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.604839] VFS: Disk quotas dquot_6.5.2
[ 0.604879] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.604962] msgmni has been set to 1735
[ 0.605138] alg: No test for stdrng (krng)
[ 0.605167] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.605170] io scheduler noop registered
[ 0.605172] io scheduler deadline registered
[ 0.605181] io scheduler cfq registered (default)
[ 0.605276] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.605310] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.605367] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.605417] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.605520] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.605550] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.605552] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.605711] acpiphp: Slot [1] registered
[ 0.605852] intel_idle: does not run on family 6 model 13
[ 0.605880] ERST: Table is not found!
[ 0.605882] GHES: HEST is not enabled!
[ 0.605896] isapnp: Scanning for PnP cards...
[ 0.960098] isapnp: No Plug & Play device found
[ 0.960166] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.960550] serial 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ
20
[ 0.960583] serial 0000:00:1e.3: PCI INT B disabled
[ 0.960676] Linux agpgart interface v0.103
[ 0.960963] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 0.966259] i8042: Detected active multiplexing controller, rev 1.1
[ 0.969343] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.969351] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.969386] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.969418] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.969449] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.969576] mousedev: PS/2 mouse device common for all mice
[ 0.969636] rtc_cmos 00:05: RTC can wake from S4
[ 0.969752] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.969783] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.969795] cpuidle: using governor ladder
[ 0.969797] cpuidle: using governor menu
[ 0.970005] TCP cubic registered
[ 0.970032] NET: Registered protocol family 10
[ 0.970540] Mobile IPv6
[ 0.970543] NET: Registered protocol family 17
[ 0.970547] Registering the dns_resolver key type
[ 0.970567] Using IPI No-Shortcut mode
[ 0.970659] PM: Hibernation image not present or could not be loaded.
[ 0.970672] registered taskstats version 1
[ 0.977274] rtc_cmos 00:05: setting system clock to 2012-08-13 09:22:11
UTC (1344849731)
[ 0.977332] Initializing network drop monitor service
[ 0.977474] Freeing unused kernel memory: 412k freed
[ 0.977663] Write protecting the kernel text: 2840k
[ 0.977696] Write protecting the kernel read-only data: 1088k
[ 0.977698] NX-protecting the kernel data: 3304k
[ 0.991760] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 0.992289] udevd[44]: starting version 175
[ 1.070043] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22,
2004)
[ 1.070072] 8139cp 0000:06:07.0: This (id 10ec:8139 rev 10) is not an
8139C+ compatible chip, use 8139too
[ 1.070469] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.070503] 8139too 0000:06:07.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 1.071910] 8139too 0000:06:07.0: eth0: RealTek RTL8139 at 0x4000,
00:16:d3:92:ec:f6, IRQ 20
[ 1.093891] usbcore: registered new interface driver usbfs
[ 1.093919] usbcore: registered new interface driver hub
[ 1.111400] firewire_ohci 0000:06:06.2: PCI INT C -> GSI 21 (level, low)
-> IRQ 21
[ 1.111555] sdhci: Secure Digital Host Controller Interface driver
[ 1.111558] sdhci: Copyright(c) Pierre Ossman
[ 1.113619] usbcore: registered new device driver usb
[ 1.114113] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.114142] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) ->
IRQ 23
[ 1.114162] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.114166] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.114193] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 1
[ 1.114226] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.118124] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.130794] SCSI subsystem initialized
[ 1.142678] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.142682] ACPI: Thermal Zone [THR0] (70 C)
[ 1.147403] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.150130] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.150134] ACPI: Thermal Zone [THR1] (62 C)
[ 1.156374] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xc8000000
[ 1.164112] firewire_ohci: Added fw-ohci device 0000:06:06.2, OHCI
v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 1.164306] sdhci-pci 0000:06:06.4: SDHCI controller found [104c:8034]
(rev 0)
[ 1.164325] sdhci-pci 0000:06:06.4: PCI INT A -> GSI 22 (level, low) ->
IRQ 22
[ 1.164376] mmc0: no vmmc regulator found
[ 1.164413] Registered led device: mmc0::
[ 1.165588] mmc0: SDHCI controller on PCI [0000:06:06.4] using PIO
[ 1.165610] mmc1: no vmmc regulator found
[ 1.165641] Registered led device: mmc1::
[ 1.166671] mmc1: SDHCI controller on PCI [0000:06:06.4] using PIO
[ 1.166691] mmc2: no vmmc regulator found
[ 1.166719] Registered led device: mmc2::
[ 1.167749] mmc2: SDHCI controller on PCI [0000:06:06.4] using PIO
[ 1.170620] libata version 3.00 loaded.
[ 1.192241] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.192272] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.192276] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.192279] usb usb1: Product: EHCI Host Controller
[ 1.192281] usb usb1: Manufacturer: Linux 3.2.0-3-686-pae ehci_hcd
[ 1.192284] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.192415] hub 1-0:1.0: USB hub found
[ 1.192421] hub 1-0:1.0: 8 ports detected
[ 1.193028] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) ->
IRQ 23
[ 1.193041] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.193046] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.193058] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 2
[ 1.193090] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[ 1.193127] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.193130] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.193133] usb usb2: Product: UHCI Host Controller
[ 1.193136] usb usb2: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.193138] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.193364] hub 2-0:1.0: USB hub found
[ 1.193369] hub 2-0:1.0: 2 ports detected
[ 1.193445] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) ->
IRQ 19
[ 1.193455] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.193459] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.193466] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 3
[ 1.193508] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 1.193544] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.193547] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.193550] usb usb3: Product: UHCI Host Controller
[ 1.193552] usb usb3: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.193555] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.193674] hub 3-0:1.0: USB hub found
[ 1.193678] hub 3-0:1.0: 2 ports detected
[ 1.193749] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) ->
IRQ 18
[ 1.193757] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.193761] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.193770] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 4
[ 1.193807] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 1.193842] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.193845] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.193848] usb usb4: Product: UHCI Host Controller
[ 1.193850] usb usb4: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.193853] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.193961] hub 4-0:1.0: USB hub found
[ 1.193965] hub 4-0:1.0: 2 ports detected
[ 1.194035] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) ->
IRQ 16
[ 1.194044] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.194048] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.194055] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus
number 5
[ 1.194093] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 1.194129] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.194133] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.194135] usb usb5: Product: UHCI Host Controller
[ 1.194138] usb usb5: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.194140] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.194247] hub 5-0:1.0: USB hub found
[ 1.194253] hub 5-0:1.0: 2 ports detected
[ 1.194328] ata_piix 0000:00:1f.1: version 2.13
[ 1.194339] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) ->
IRQ 18
[ 1.194377] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.207476] scsi0 : ata_piix
[ 1.208805] scsi1 : ata_piix
[ 1.209318] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18c0 irq
14
[ 1.209322] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18c8 irq
15
[ 1.209756] ata2: port disabled--ignoring
[ 1.380526] ata1.00: ATA-8: INTEL SSDSA2CW080G3, 4PC10362, max UDMA/133
[ 1.380530] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/1)
[ 1.392538] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 1.405907] ata1.01: ATA-8: WDC WD3200BEVE-00A0HT0, 11.01A11, max
UDMA/100
[ 1.405911] ata1.01: 625142448 sectors, multi 16: LBA48
[ 1.421331] ata1.00: configured for UDMA/100
[ 1.437320] ata1.01: configured for UDMA/100
[ 1.437446] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW08
4PC1 PQ: 0 ANSI: 5
[ 1.437758] scsi 0:0:1:0: Direct-Access ATA WDC WD3200BEVE-0
11.0 PQ: 0 ANSI: 5
[ 1.445599] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0
GB/74.5 GiB)
[ 1.445672] sd 0:0:0:0: [sda] Write Protect is off
[ 1.445676] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.445699] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.446483] sda: sda1
[ 1.446774] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.446804] sd 0:0:1:0: [sdb] 625142448 512-byte logical blocks: (320
GB/298 GiB)
[ 1.446855] sd 0:0:1:0: [sdb] Write Protect is off
[ 1.446858] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.446881] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.480402] sdb: sdb1 sdb2 < sdb5 >
[ 1.481181] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 1.564020] Refined TSC clocksource calibration: 1995.596 MHz.
[ 1.564027] Switching to clocksource tsc
[ 1.592460] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 1.664097] firewire_core: created device fw0: GUID 07e40a0093985009,
S400
[ 1.792528] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 1.992464] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 2.236020] EXT4-fs (sda1): mounted filesystem with ordered data mode.
Opts: (null)
[ 2.515555] udevd[273]: starting version 175
[ 2.634690] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 2.636618] ACPI: Requesting acpi_cpufreq
[ 2.636695] ACPI: Lid Switch [LID0]
[ 2.636768] input: Sleep Button as
/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 2.636775] ACPI: Sleep Button [SLPB]
[ 2.636833] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 2.636837] ACPI: Power Button [PWB]
[ 2.651523] Marking TSC unstable due to TSC halts in idle
[ 2.651546] ACPI: acpi_idle registered with cpuidle
[ 2.652057] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 2.652065] ACPI: Power Button [PWRF]
[ 2.662201] Switching to clocksource hpet
[ 2.671851] wmi: Mapper loaded
[ 2.719005] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5
[ 2.719015] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 2.733659] ACPI: AC Adapter [AC] (on-line)
[ 2.767445] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) ->
IRQ 19
[ 2.767452] ACPI: resource 0000:00:1f.3 [io 0x18e0-0x18ff] conflicts
with ACPI region SMBI [io 0x18e0-0x18ef]
[ 2.767456] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 2.770380] ACPI: Battery Slot [BAT0] (battery present)
[ 2.777358] yenta_cardbus 0000:06:06.0: CardBus bridge found [103c:309d]
[ 2.777384] yenta_cardbus 0000:06:06.0: Enabling burst memory read
transactions
[ 2.777390] yenta_cardbus 0000:06:06.0: Using CSCINT to route CSC
interrupts to PCI
[ 2.777393] yenta_cardbus 0000:06:06.0: Routing CardBus interrupts to PCI
[ 2.777399] yenta_cardbus 0000:06:06.0: TI: mfunc 0x01aa1b02, devctl 0x64
[ 2.777606] intel_rng: FWH not detected
[ 2.782336] iTCO_vendor_support: vendor-support=0
[ 2.786122] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 2.786220] iTCO_wdt: Found a ICH6-M TCO device (Version=2,
TCOBASE=0x1060)
[ 2.786285] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 2.791248] cfg80211: Calling CRDA to update world regulatory domain
[ 2.796350] [drm] Initialized drm 1.1.0 20060810
[ 2.796869] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 2.806052] lib80211: common routines for IEEE802.11 drivers
[ 2.806056] lib80211_crypt: registered algorithm 'NULL'
[ 2.810528] libipw: 802.11 data/management/control stack, git-1.1.13
[ 2.810531] libipw: Copyright (C) 2004-2005 Intel Corporation <
jketreno@linux.intel.com>
[ 2.819095] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
1.2.2kmprq
[ 2.819098] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 2.880413] [drm] radeon kernel modesetting enabled.
[ 2.880541] radeon 0000:01:00.0: power state changed by ACPI to D0
[ 2.880546] radeon 0000:01:00.0: power state changed by ACPI to D0
[ 2.880555] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 2.880562] radeon 0000:01:00.0: setting latency timer to 64
[ 2.880724] [drm] initializing kernel modesetting (RV410 0x1002:0x5653
0x103C:0x309E).
[ 2.880745] [drm] register mmio base: 0xC8100000
[ 2.880747] [drm] register mmio size: 65536
[ 2.880935] ATOM BIOS: HP
[ 2.880957] [drm] Generation 2 PCI interface, using max accessible memory
[ 2.880962] radeon 0000:01:00.0: VRAM: 128M 0x00000000D0000000 -
0x00000000D7FFFFFF (128M used)
[ 2.880966] radeon 0000:01:00.0: GTT: 512M 0x00000000B0000000 -
0x00000000CFFFFFFF
[ 2.880980] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.880982] [drm] Driver supports precise vblank timestamp query.
[ 2.881022] radeon 0000:01:00.0: irq 42 for MSI/MSI-X
[ 2.881028] radeon 0000:01:00.0: radeon: using MSI.
[ 2.881051] [drm] radeon: irq initialized.
[ 2.890123] [drm] Detected VRAM RAM=128M, BAR=128M
[ 2.890126] [drm] RAM width 128bits DDR
[ 2.901092] [TTM] Zone kernel: Available graphics memory: 444380 kiB.
[ 2.901096] [TTM] Zone highmem: Available graphics memory: 1036704 kiB.
[ 2.901099] [TTM] Initializing pool allocator.
[ 2.901126] [drm] radeon: 128M of VRAM memory ready
[ 2.901129] [drm] radeon: 512M of GTT memory ready.
[ 2.901153] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 2.903881] [drm] PCIE GART of 512M enabled (table at
0x00000000D0040000).
[ 2.903893] [drm] radeon: 2 quad pipes, 1 z pipes initialized.
[ 2.903930] radeon 0000:01:00.0: WB enabled
[ 2.930062] [drm] Loading R400 Microcode
[ 2.930934] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 2.992538] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 3.008993] yenta_cardbus 0000:06:06.0: ISA IRQ mask 0x0cf8, PCI irq 22
[ 3.008998] yenta_cardbus 0000:06:06.0: Socket status: 30000006
[ 3.009003] pci_bus 0000:06: Raising subordinate bus# of parent bus
(#06) from #07 to #0a
[ 3.009014] yenta_cardbus 0000:06:06.0: pcmcia: parent PCI bridge
window: [io 0x4000-0x4fff]
[ 3.009017] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x4000-0x4fff:
[ 3.010130] [drm] radeon: ring at 0x00000000B0001000
[ 3.010151] [drm] ring test succeeded in 1 usecs
[ 3.010313] [drm] radeon: ib pool ready.
[ 3.010880] [drm] ib test succeeded in 0 usecs
[ 3.011411] [drm] Radeon Display Connectors
[ 3.011414] [drm] Connector 0:
[ 3.011416] [drm] VGA
[ 3.011420] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 3.011422] [drm] Encoders:
[ 3.011424] [drm] CRT1: INTERNAL_DAC1
[ 3.011427] [drm] Connector 1:
[ 3.011428] [drm] LVDS
[ 3.011431] [drm] DDC: 0x68 0x68 0x68 0x68 0x68 0x68 0x68 0x68
[ 3.011434] [drm] Encoders:
[ 3.011436] [drm] LCD1: INTERNAL_LVDS
[ 3.011438] [drm] Connector 2:
[ 3.011440] [drm] S-video
[ 3.011442] [drm] Encoders:
[ 3.011444] [drm] TV1: INTERNAL_DAC2
[ 3.011461] [drm] radeon: power management initialized
[ 3.310025] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 3.314811] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff
[ 3.335796] yenta_cardbus 0000:06:06.0: pcmcia: parent PCI bridge
window: [mem 0xc8200000-0xc82fffff]
[ 3.335801] pcmcia_socket pcmcia_socket0: cs: memory probe
0xc8200000-0xc82fffff: excluding 0xc8200000-0xc820ffff
[ 3.335821] yenta_cardbus 0000:06:06.0: pcmcia: parent PCI bridge
window: [mem 0x80000000-0x83ffffff pref]
[ 3.335825] pcmcia_socket pcmcia_socket0: cs: memory probe
0x80000000-0x83ffffff: excluding 0x80000000-0x83ffffff
[ 3.341417] ipw2200 0000:06:05.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 3.341447] ipw2200: Detected Intel PRO/Wireless 2200BG Network
Connection
[ 3.350502] cfg80211: World regulatory domain updated:
[ 3.350506] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 3.350510] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 3.350513] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300
mBi, 2000 mBm)
[ 3.350516] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300
mBi, 2000 mBm)
[ 3.350519] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 3.350523] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 3.358949] snd_intel8x0 0000:00:1e.2: PCI INT A -> GSI 17 (level, low)
-> IRQ 17
[ 3.359059] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 3.414047] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
excluding 0x170-0x177 0x1f0-0x1f7 0x200-0x20f 0x370-0x377
[ 3.415994] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
excluding 0x3f0-0x3f7 0x4d0-0x4d7
[ 3.417071] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
clean.
[ 3.420060] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
clean.
[ 3.420992] pcmcia_socket pcmcia_socket0: cs: memory probe
0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xdc000-0xfffff
[ 3.421025] pcmcia_socket pcmcia_socket0: cs: memory probe
0xa0000000-0xa0ffffff: clean.
[ 3.421059] pcmcia_socket pcmcia_socket0: cs: memory probe
0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[ 3.421089] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
clean.
[ 3.546082] ipw2200: Radio Frequency Kill Switch is On:
[ 3.546084] Kill switch must be turned off for wireless networking to
work.
[ 3.549731] cfg80211: failed to add phy80211 symlink to netdev!
[ 3.550072] ipw2200: Detected geography ZZM (11 802.11bg channels, 0
802.11a channels)
[ 3.550105] tifm_7xx1 0000:06:06.3: PCI INT A -> GSI 22 (level, low) ->
IRQ 22
[ 3.651485] [drm] fb mappable at 0xD00C0000
[ 3.651489] [drm] vram apper at 0xD0000000
[ 3.651491] [drm] size 4096000
[ 3.651492] [drm] fb depth is 24
[ 3.651494] [drm] pitch is 5120
[ 3.652276] fbcon: radeondrmfb (fb0) is primary device
[ 4.240502] Console: switching to colour frame buffer device 160x50
[ 4.253399] fb0: radeondrmfb frame buffer device
[ 4.253403] drm: registered panic notifier
[ 4.253430] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on
minor 0
[ 4.564056] intel8x0_measure_ac97_clock: measured 55182 usecs (2659
samples)
[ 4.564064] intel8x0: clocking to 48000
[ 4.566811] snd_intel8x0m 0000:00:1e.3: PCI INT B -> GSI 20 (level, low)
-> IRQ 20
[ 4.566842] snd_intel8x0m 0000:00:1e.3: setting latency timer to 64
[ 4.689782] Adding 2650688k swap on /dev/sdb5. Priority:-1 extents:1
across:2650688k
[ 4.701979] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 4.753711] EXT4-fs (sda1): re-mounted. Opts:
errors=remount-ro,commit=600
[ 4.789849] loop: module loaded
[ 4.852269] input: PS/2 Mouse as
/devices/platform/i8042/serio4/input/input8
[ 4.872577] input: AlpsPS/2 ALPS GlidePoint as
/devices/platform/i8042/serio4/input/input9
[ 5.710712] EXT4-fs (sdb1): mounted filesystem with ordered data mode.
Opts: errors=remount-ro
[ 6.024504] RPC: Registered named UNIX socket transport module.
[ 6.024508] RPC: Registered udp transport module.
[ 6.024510] RPC: Registered tcp transport module.
[ 6.024512] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.032946] FS-Cache: Loaded
[ 6.052483] FS-Cache: Netfs 'nfs' registered for caching
[ 6.064252] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 6.919374] 8139too 0000:06:07.0: eth0: link up, 100Mbps, full-duplex,
lpa 0x45E1
[ 7.999779] input: ACPI Virtual Keyboard Device as
/devices/virtual/input/input10
[ 9.069848] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
[ 9.084844] microcode: Microcode Update Driver: v2.00 <
tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 14.976231] fuse init (API version 7.17)
 
Old 10-02-2012, 06:20 PM
Anssi Hannula
 
Default Bug#684352: phy0/hp-wifi problems after kernel update from 2.6 to 3.2

Hi,

02.10.2012 17:28, David Smith kirjoitti:
>
> Hello, I'm having a problem with my Intel 2200 wireless on my Compaq
> Presario V4000T (made by HP) that has started happening after I upgraded
> my kernel from 2.6 to 3.2.
>
> Problem: phy0 wireless state is incorrect.
>
> Steps to reproduce problem:
> 1. Upgrade kernel from 2.6 to 3.2
> 2. rfkill now reports that I have two wireless devices but I only have
> the Intel 2200 wireless:
>
> Miho:/home/david# rfkill list all
> 0: hp-wifi: Wireless LAN
> Soft blocked: yes
> Hard blocked: no
> 1: phy0: Wireless LAN
> Soft blocked: yes
> Hard blocked: yes
>
> 3. The wireless simply doesn't work anymore because all software
> believes the wireless is blocked with a hardware switch, which is not
> the case.
>
> After many many hours of searching, I discovered that running "rfkill
> unblock all" is able to remove the "Hard Block" from phy0 and put the
> wireless into this state:

Sounds like the "hp-wifi" soft block status affects "phy0" hard block
status. So if some management program softblocks "hp-wifi", the "phy0"
will become hardblocked and the program doesn't understand that it needs
to unblock "hp-wifi" again to undo what it just did.

I have no idea what is the proper course of action here, though, but
hopefully someone else on the lists has an idea.



>
> Miho:/home/david# rfkill unblock all
> Miho:/home/david# rfkill list all
> 0: hp-wifi: Wireless LAN
> Soft blocked: no
> Hard blocked: no
> 1: phy0: Wireless LAN
> Soft blocked: no
> Hard blocked: no
> Miho:/home/david#
>
>
> However, I find that I have to keep dropping to a console and running
> "sudo rfkill unblock all" because the hardware keeps going back into the
> first state where phy0 is reporting that it is hard blocked, when it
> really isn't.
>
>
>
> Workaround #1: Set "ACPI=off" on 3.2 kernel. After which, the wireless
> appears to be correctly reported:
> Miho:/home/david# rfkill list all
> 0: phy0: Wireless LAN
> Soft blocked: no
> Hard blocked: no
>
> This causes phy0 to accurately reflect the state of the hardware.
>
> Workaround #2: Add hp-wmi to modprobe blacklist. Again, this causes
> only phy0 wireless to be reported and phy0 always accurately reflects
> the state of the hardware (both soft and hard blocked).
>
> Expected Results;
> Both phy0 and hp-wifi refer to the same hardware device so they should
> accurately report the correct state of that hardware device.
>
> Actual Results:
> Phy0 reports it is hard blocked when there is no hard block on the
> wireless. Further, phy0 keeps going into this "hard blocked" state from
> regular usage of the wireless with networkmanager, while the hp-wmi does
> not. If I remove the hp-wmi then the phy0 works properly. When I have
> hp-wmi, then phy0's state is often incorrect. It seems there may be
> some conflict here between phy0 and hp-wmi.
>
>
>
> Kernel versions tested:
> linux-image-3.2.0-3-686-pae: Wireless regularly gets into this "bad
> state" of reporting it's hard blocked when it isn't. Unable to recover
> from it without using "sudo rfkill unblock all".
>
> linux-image-2.6.32-5-686: No problem at all
>
>
> PCI registers from the only wireless device I have in this PC:
>
> Miho:/home/david# lspci -vv -s06:05.0
> 06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG
> [Calexico2] Network Connection (rev 05)
> Subsystem: Hewlett-Packard Company Device 12f5
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 128 (750ns min, 6000ns max), Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 20
> Region 0: Memory at c8206000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> Kernel driver in use: ipw2200
>
> Miho:/home/david#
>
>
> Somehow network manager is putting phy0 into a "hard blocked" state, but
> the hardware is not really hardblocked. After going into this hard
> blocked state, the wireless cannot be used anymore unless dropping to a
> console and running sudo rfkill unblock all which removes the "hard
> block" from phy0. Networkmanager alone is not able to bring the wireless
> back up.
>
> Also, sometimes when I turn on the PC, or resume from hibernate the
> rfkill reports phy0 as hard blocked, when it isn't. Which again, forces
> me to drop to console and run a "sudo rfkill unblock all"
>
> I am currently using Workaround #2 and am very happy with it. The
> wireless no longer goes into "hard blocked" through normal usage of the
> hardware with network manager.
>
> Thank you for your time.

--
Anssi Hannula


--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 506B3052.4000206@iki.fi">http://lists.debian.org/506B3052.4000206@iki.fi
 
Old 10-04-2012, 02:15 PM
David Smith
 
Default Bug#684352: phy0/hp-wifi problems after kernel update from 2.6 to 3.2

(My apologies if I accidentally post this twice as I keep getting mail
server rejection messages.)

Hello, I'm having a problem with my Intel 2200 wireless on my Compaq
Presario V4000T (made by HP) that has started happening after I
upgraded my kernel from 2.6 to 3.2.

Problem: phy0 wireless state is incorrect.

Steps to reproduce problem:
1. Upgrade kernel from 2.6 to 3.2
2. rfkill now reports that I have two wireless devices but I only have
the Intel 2200 wireless:

Miho:/home/david# rfkill list all
0: hp-wifi: Wireless LAN
Soft blocked: yes
Hard blocked: no
1: phy0: Wireless LAN
Soft blocked: yes
Hard blocked: yes

3. The wireless simply doesn't work anymore because all software
believes the wireless is blocked with a hardware switch, which is not
the case.

After many many hours of searching, I discovered that running "rfkill
unblock all" is able to remove the "Hard Block" from phy0 and put the
wireless into this state:


Miho:/home/david# rfkill unblock all
Miho:/home/david# rfkill list all
0: hp-wifi: Wireless LAN
Soft blocked: no
Hard blocked: no
1: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
Miho:/home/david#


However, I find that I have to keep dropping to a console and running
"sudo rfkill unblock all" because the hardware keeps going back into
the first state where phy0 is reporting that it is hard blocked, when
it really isn't.



Workaround #1: Set "ACPI=off" on 3.2 kernel. After which, the wireless
appears to be correctly reported:
Miho:/home/david# rfkill list all
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no

This causes phy0 to accurately reflect the state of the hardware.

Workaround #2: Add hp-wmi to modprobe blacklist. Again, this causes
only phy0 wireless to be reported and phy0 always accurately reflects
the state of the hardware (both soft and hard blocked).

Expected Results;
Both phy0 and hp-wifi refer to the same hardware device so they should
accurately report the correct state of that hardware device.

Actual Results:
Phy0 reports it is hard blocked when there is no hard block on the
wireless. Further, phy0 keeps going into this "hard blocked" state
from regular usage of the wireless with networkmanager, while the
hp-wmi does not. If I remove the hp-wmi then the phy0 works properly.
When I have hp-wmi, then phy0's state is often incorrect. It seems
there may be some conflict here between phy0 and hp-wmi.



Kernel versions tested:
linux-image-3.2.0-3-686-pae: Wireless regularly gets into this "bad
state" of reporting it's hard blocked when it isn't. Unable to recover
from it without using "sudo rfkill unblock all".

linux-image-2.6.32-5-686: No problem at all


PCI registers from the only wireless device I have in this PC:

Miho:/home/david# lspci -vv -s06:05.0
06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG
[Calexico2] Network Connection (rev 05)
Subsystem: Hewlett-Packard Company Device 12f5
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (750ns min, 6000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c8206000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Kernel driver in use: ipw2200

Miho:/home/david#


Somehow network manager is putting phy0 into a "hard blocked" state,
but the hardware is not really hardblocked. After going into this hard
blocked state, the wireless cannot be used anymore unless dropping to
a console and running sudo rfkill unblock all which removes the "hard
block" from phy0. Networkmanager alone is not able to bring the
wireless back up.

Also, sometimes when I turn on the PC, or resume from hibernate the
rfkill reports phy0 as hard blocked, when it isn't. Which again,
forces me to drop to console and run a "sudo rfkill unblock all"

I am currently using Workaround #2 and am happy with it. The wireless
no longer goes into "hard blocked" through normal usage of the
hardware with network manager.

References: http://bugs.debian.org/684352

Thank you for your time.

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-3-686-pae (Debian 3.2.21-3) (
debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-8) ) #1
SMP Thu Jun 28 08:56:46 UTC 2012
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007feeb000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007feeb000 - 000000007ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] DMI: Hewlett-Packard Pavilion dv4000 (x123xx#ABA)/309E, BIOS
F.15 05/24/2006
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000
(usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000
(usable)
[ 0.000000] last_pfn = 0x7fee0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E3FFF uncachable
[ 0.000000] E4000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 07FF00000 mask FFFF00000 uncachable
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] PAT not supported by CPU.
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[ 0.000000] RAMDISK: 36714000 - 37382000
[ 0.000000] ACPI: RSDP 000f76a0 00014 (v00 HP )
[ 0.000000] ACPI: RSDT 7fee51c1 00044 (v01 HP 309E 06040000 LTP
00000000)
[ 0.000000] ACPI: FACP 7feeae88 00074 (v01 HP 309E 06040000 LOHR
0000005F)
[ 0.000000] ACPI: DSDT 7fee5a66 05422 (v01 HP 309E 06040000 MSFT
0100000E)
[ 0.000000] ACPI: FACS 7fefbfc0 00040
[ 0.000000] ACPI: APIC 7feeaefc 00068 (v01 HP 309E 06040000 LOHR
0000005F)
[ 0.000000] ACPI: BOOT 7feeafd8 00028 (v01 HP 309E 06040000 LTP
00000001)
[ 0.000000] ACPI: MCFG 7feeaf9c 0003C (v01 HP 309E 06040000 LOHR
0000005F)
[ 0.000000] ACPI: SSDT 7fee561d 00277 (v01 HP 309E 00003000 INTL
20030224)
[ 0.000000] ACPI: SSDT 7fee5445 001D8 (v01 HP 309E 00003001 INTL
20030224)
[ 0.000000] ACPI: SSDT 7fee5331 00114 (v01 HP 309E 00003000 INTL
20030224)
[ 0.000000] ACPI: SSDT 7fee5205 0012C (v01 HP 309E 00000001 INTL
20030224)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1156MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0007fee0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0007fee0
[ 0.000000] On node 0 totalpages: 523887
[ 0.000000] free_area_init_node: node 0, pgdat c140d640, node_mem_map
f5714200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2314 pages used for memmap
[ 0.000000] HighMem zone: 293848 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 -
00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 -
00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 -
0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap:
80000000:60000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2
nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @f79d5000 s33280 r0 d24064
u57344
[ 0.000000] pcpu-alloc: s33280 r0 d24064 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 519793
[ 0.000000] Kernel command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-3-686-pae
root=UUID=7397b469-cdfc-4e8a-ae54-294d980fefb4 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000379fe:0007fee0)
[ 0.000000] Memory: 2060268k/2096000k available (2836k kernel code,
35280k reserved, 1343k data, 412k init, 1184648k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc1415000 - 0xc147c000 ( 412 kB)
[ 0.000000] .data : 0xc12c50ec - 0xc1414f00 (1343 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12c50ec (2836 kB)
[ 0.000000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=f7406000 soft=f7408000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1995.689 MHz processor.
[ 0.008003] Calibrating delay loop (skipped), value calculated using
timer frequency.. 3991.37 BogoMIPS (lpj=7982756)
[ 0.008009] pid_max: default: 32768 minimum: 301
[ 0.008058] Security Framework initialized
[ 0.008068] AppArmor: AppArmor disabled by boot time parameter
[ 0.008087] Mount-cache hash table entries: 512
[ 0.008250] Initializing cgroup subsys cpuacct
[ 0.008257] Initializing cgroup subsys memory
[ 0.008268] Initializing cgroup subsys devices
[ 0.008271] Initializing cgroup subsys freezer
[ 0.008273] Initializing cgroup subsys net_cls
[ 0.008276] Initializing cgroup subsys blkio
[ 0.008284] Initializing cgroup subsys perf_event
[ 0.008316] Disabled fast string operations
[ 0.008326] mce: CPU supports 5 MCE banks
[ 0.008337] CPU0: Thermal monitoring enabled (TM2)
[ 0.008401] SMP alternatives: switching to UP code
[ 0.011453] ACPI: Core revision 20110623
[ 0.016071] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.016515] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.057014] CPU0: Intel(R) Pentium(R) M processor 2.00GHz stepping 08
[ 0.060003] Performance Events: p6 PMU driver.
[ 0.060003] ... version: 0
[ 0.060003] ... bit width: 32
[ 0.060003] ... generic registers: 2
[ 0.060003] ... value mask: 00000000ffffffff
[ 0.060003] ... max period: 000000007fffffff
[ 0.060003] ... fixed-purpose events: 0
[ 0.060003] ... event mask: 0000000000000003
[ 0.060003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.060003] Brought up 1 CPUs
[ 0.060003] Total of 1 processors activated (3991.37 BogoMIPS).
[ 0.060003] devtmpfs: initialized
[ 0.060003] PM: Registering ACPI NVS region at 7feeb000 (86016 bytes)
[ 0.060003] print_constraints: dummy:
[ 0.060003] NET: Registered protocol family 16
[ 0.060003] ACPI: bus type pci registered
[ 0.060003] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem
0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.060003] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.060003] PCI: Using MMCONFIG for extended config space
[ 0.060003] PCI: Using configuration type 1 for base access
[ 0.060003] bio: create slab <bio-0> at 0
[ 0.060003] ACPI: Added _OSI(Module Device)
[ 0.060003] ACPI: Added _OSI(Processor Device)
[ 0.060003] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.060003] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.060017] ACPI: EC: Look up EC in DSDT
[ 0.061985] ACPI: Interpreter enabled
[ 0.061998] ACPI: (supports S0 S3 S4 S5)
[ 0.062020] ACPI: Using IOAPIC for interrupt routing
[ 0.068551] ACPI: EC: GPE = 0x1b, I/O: command/status = 0x66, data = 0x62
[ 0.068666] ACPI: No dock devices found.
[ 0.068668] HEST: Table not found.
[ 0.068674] PCI: Ignoring host bridge windows from ACPI; if necessary,
use "pci=use_crs" and report a bug
[ 0.069017] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.069702] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
(ignored)
[ 0.069706] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
(ignored)
[ 0.069709] pci_root PNP0A08:00: host bridge window [mem
0x000a0000-0x000bffff] (ignored)
[ 0.069713] pci_root PNP0A08:00: host bridge window [mem
0x000d0000-0x000d3fff] (ignored)
[ 0.069716] pci_root PNP0A08:00: host bridge window [mem
0x000d4000-0x000d7fff] (ignored)
[ 0.069719] pci_root PNP0A08:00: host bridge window [mem
0x000d8000-0x000dbfff] (ignored)
[ 0.069723] pci_root PNP0A08:00: host bridge window [mem
0x80000000-0xfebfffff] (ignored)
[ 0.069735] pci 0000:00:00.0: [8086:2590] type 0 class 0x000600
[ 0.069780] pci 0000:00:01.0: [8086:2591] type 1 class 0x000604
[ 0.069820] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.069824] pci 0000:00:01.0: PME# disabled
[ 0.069879] pci 0000:00:1c.0: [8086:2660] type 1 class 0x000604
[ 0.069979] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.069985] pci 0000:00:1c.0: PME# disabled
[ 0.070019] pci 0000:00:1d.0: [8086:2658] type 0 class 0x000c03
[ 0.070072] pci 0000:00:1d.0: reg 20: [io 0x1800-0x181f]
[ 0.070112] pci 0000:00:1d.1: [8086:2659] type 0 class 0x000c03
[ 0.072010] pci 0000:00:1d.1: reg 20: [io 0x1820-0x183f]
[ 0.072050] pci 0000:00:1d.2: [8086:265a] type 0 class 0x000c03
[ 0.072103] pci 0000:00:1d.2: reg 20: [io 0x1840-0x185f]
[ 0.072144] pci 0000:00:1d.3: [8086:265b] type 0 class 0x000c03
[ 0.072197] pci 0000:00:1d.3: reg 20: [io 0x1860-0x187f]
[ 0.072247] pci 0000:00:1d.7: [8086:265c] type 0 class 0x000c03
[ 0.072270] pci 0000:00:1d.7: reg 10: [mem 0xc8000000-0xc80003ff]
[ 0.072368] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.072373] pci 0000:00:1d.7: PME# disabled
[ 0.072396] pci 0000:00:1e.0: [8086:2448] type 1 class 0x000604
[ 0.072483] pci 0000:00:1e.2: [8086:266e] type 0 class 0x000401
[ 0.072503] pci 0000:00:1e.2: reg 10: [io 0x1c00-0x1cff]
[ 0.072515] pci 0000:00:1e.2: reg 14: [io 0x1880-0x18bf]
[ 0.072527] pci 0000:00:1e.2: reg 18: [mem 0xc8000800-0xc80009ff]
[ 0.072538] pci 0000:00:1e.2: reg 1c: [mem 0xc8000400-0xc80004ff]
[ 0.072597] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold
[ 0.072602] pci 0000:00:1e.2: PME# disabled
[ 0.072622] pci 0000:00:1e.3: [8086:266d] type 0 class 0x000703
[ 0.072642] pci 0000:00:1e.3: reg 10: [io 0x2400-0x24ff]
[ 0.072654] pci 0000:00:1e.3: reg 14: [io 0x2000-0x207f]
[ 0.072730] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold
[ 0.072735] pci 0000:00:1e.3: PME# disabled
[ 0.072757] pci 0000:00:1f.0: [8086:2641] type 0 class 0x000601
[ 0.072860] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.072869] pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6
ACPI/GPIO/TCO
[ 0.072876] pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6
GPIO
[ 0.072901] pci 0000:00:1f.1: [8086:266f] type 0 class 0x000101
[ 0.072918] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.072929] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.072941] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.072953] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.072964] pci 0000:00:1f.1: reg 20: [io 0x18c0-0x18cf]
[ 0.073009] pci 0000:00:1f.3: [8086:266a] type 0 class 0x000c05
[ 0.073078] pci 0000:00:1f.3: reg 20: [io 0x18e0-0x18ff]
[ 0.073159] pci 0000:01:00.0: [1002:5653] type 0 class 0x000300
[ 0.073170] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xd7ffffff pref]
[ 0.073178] pci 0000:01:00.0: reg 14: [io 0x3000-0x30ff]
[ 0.073186] pci 0000:01:00.0: reg 18: [mem 0xc8100000-0xc810ffff]
[ 0.073210] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.073239] pci 0000:01:00.0: supports D1 D2
[ 0.073249] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.
You can enable it with 'pcie_aspm=force'
[ 0.073258] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.073262] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 0.073265] pci 0000:00:01.0: bridge window [mem 0xc8100000-0xc81fffff]
[ 0.073269] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xd7ffffff
pref]
[ 0.073325] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.073391] pci 0000:06:05.0: [8086:4220] type 0 class 0x000280
[ 0.073419] pci 0000:06:05.0: reg 10: [mem 0xc8206000-0xc8206fff]
[ 0.073545] pci 0000:06:05.0: PME# supported from D0 D3hot D3cold
[ 0.073551] pci 0000:06:05.0: PME# disabled
[ 0.073577] pci 0000:06:06.0: [104c:8031] type 2 class 0x000607
[ 0.073606] pci 0000:06:06.0: reg 10: [mem 0xc8207000-0xc8207fff]
[ 0.073649] pci 0000:06:06.0: supports D1 D2
[ 0.073652] pci 0000:06:06.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.073658] pci 0000:06:06.0: PME# disabled
[ 0.073686] pci 0000:06:06.2: [104c:8032] type 0 class 0x000c00
[ 0.073713] pci 0000:06:06.2: reg 10: [mem 0xc8208000-0xc82087ff]
[ 0.073731] pci 0000:06:06.2: reg 14: [mem 0xc8200000-0xc8203fff]
[ 0.073844] pci 0000:06:06.2: supports D1 D2
[ 0.073847] pci 0000:06:06.2: PME# supported from D0 D1 D2 D3hot
[ 0.073853] pci 0000:06:06.2: PME# disabled
[ 0.073879] pci 0000:06:06.3: [104c:8033] type 0 class 0x000180
[ 0.073906] pci 0000:06:06.3: reg 10: [mem 0xc8204000-0xc8205fff]
[ 0.074029] pci 0000:06:06.3: supports D1 D2
[ 0.074032] pci 0000:06:06.3: PME# supported from D0 D1 D2 D3hot
[ 0.074038] pci 0000:06:06.3: PME# disabled
[ 0.074063] pci 0000:06:06.4: [104c:8034] type 0 class 0x000805
[ 0.074090] pci 0000:06:06.4: reg 10: [mem 0xc8209000-0xc82090ff]
[ 0.074106] pci 0000:06:06.4: reg 14: [mem 0xc8208c00-0xc8208cff]
[ 0.074124] pci 0000:06:06.4: reg 18: [mem 0xc8208800-0xc82088ff]
[ 0.074221] pci 0000:06:06.4: supports D1 D2
[ 0.074223] pci 0000:06:06.4: PME# supported from D0 D1 D2 D3hot
[ 0.074230] pci 0000:06:06.4: PME# disabled
[ 0.074261] pci 0000:06:07.0: [10ec:8139] type 0 class 0x000200
[ 0.074289] pci 0000:06:07.0: reg 10: [io 0x4000-0x40ff]
[ 0.074305] pci 0000:06:07.0: reg 14: [mem 0xc8209400-0xc82094ff]
[ 0.074416] pci 0000:06:07.0: supports D1 D2
[ 0.074418] pci 0000:06:07.0: PME# supported from D1 D2 D3hot D3cold
[ 0.074425] pci 0000:06:07.0: PME# disabled
[ 0.074477] pci 0000:00:1e.0: PCI bridge to [bus 06-07] (subtractive
decode)
[ 0.074482] pci 0000:00:1e.0: bridge window [io 0x4000-0x4fff]
[ 0.074488] pci 0000:00:1e.0: bridge window [mem 0xc8200000-0xc82fffff]
[ 0.074496] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff]
(subtractive decode)
[ 0.074499] pci 0000:00:1e.0: bridge window [mem
0x00000000-0xffffffff] (subtractive decode)
[ 0.074554] pci_bus 0000:07: [bus 07-0a] partially hidden behind
transparent bridge 0000:06 [bus 06-07]
[ 0.074573] pci_bus 0000:00: on NUMA node 0
[ 0.074576] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.074709] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.074778] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.074861] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.074966] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.074970] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND),
returned control mask: 0x1d
[ 0.074972] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.077846] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14
15) *11
[ 0.077906] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14
15) *10
[ 0.077962] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14
15)
[ 0.078018] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14
15) *10
[ 0.078073] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14
15) *11
[ 0.078129] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14
15)
[ 0.078185] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14
15)
[ 0.078240] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14
15)
[ 0.078351] vgaarb: device added:
PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.078356] vgaarb: loaded
[ 0.078358] vgaarb: bridge control possible 0000:01:00.0
[ 0.078398] PCI: Using ACPI for IRQ routing
[ 0.088176] PCI: pci_cache_line_size set to 64 bytes
[ 0.088267] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.088270] reserve RAM buffer: 000000007fee0000 - 000000007fffffff
[ 0.088501] hpet clockevent registered
[ 0.088506] HPET: 3 timers in total, 0 timers will be used for per-cpu
timer
[ 0.088513] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.088518] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.092041] Switching to clocksource hpet
[ 0.093903] pnp: PnP ACPI init
[ 0.093918] ACPI: bus type pnp registered
[ 0.094267] pnp 00:00: [bus 00-ff]
[ 0.094271] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.094274] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.094276] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.094279] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.094282] pnp 00:00: [mem 0x000c0000-0x000c3fff window]
[ 0.094285] pnp 00:00: [mem 0x000c4000-0x000c7fff window]
[ 0.094288] pnp 00:00: [mem 0x000c8000-0x000cbfff window]
[ 0.094291] pnp 00:00: [mem 0x000cc000-0x000cffff window]
[ 0.094293] pnp 00:00: [mem 0x000d0000-0x000d3fff window]
[ 0.094296] pnp 00:00: [mem 0x000d4000-0x000d7fff window]
[ 0.094299] pnp 00:00: [mem 0x000d8000-0x000dbfff window]
[ 0.094302] pnp 00:00: [mem 0x000dc000-0x000dffff window]
[ 0.094305] pnp 00:00: [mem 0x000e0000-0x000e3fff window]
[ 0.094308] pnp 00:00: [mem 0x000e4000-0x000e7fff window]
[ 0.094310] pnp 00:00: [mem 0x000e8000-0x000ebfff window]
[ 0.094313] pnp 00:00: [mem 0x000ec000-0x000effff window]
[ 0.094316] pnp 00:00: [mem 0x000f0000-0x000fffff window]
[ 0.094319] pnp 00:00: [mem 0x80000000-0xfebfffff window]
[ 0.094365] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03
(active)
[ 0.095322] pnp 00:01: [io 0x0000-0x001f]
[ 0.095325] pnp 00:01: [io 0x0081-0x0091]
[ 0.095327] pnp 00:01: [io 0x0093-0x009f]
[ 0.095330] pnp 00:01: [io 0x00c0-0x00df]
[ 0.095332] pnp 00:01: [dma 4]
[ 0.095370] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.095381] pnp 00:02: [mem 0xff800000-0xffffffff]
[ 0.095420] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.095457] pnp 00:03: [io 0x00f0]
[ 0.095467] pnp 00:03: [irq 13]
[ 0.095506] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.095520] pnp 00:04: [io 0x004e-0x004f]
[ 0.095522] pnp 00:04: [io 0x0061]
[ 0.095525] pnp 00:04: [io 0x0063]
[ 0.095527] pnp 00:04: [io 0x0065]
[ 0.095529] pnp 00:04: [io 0x0067]
[ 0.095531] pnp 00:04: [io 0x0080]
[ 0.095534] pnp 00:04: [io 0x0092]
[ 0.095536] pnp 00:04: [io 0x00b2-0x00b3]
[ 0.095538] pnp 00:04: [io 0x0200-0x020f]
[ 0.095541] pnp 00:04: [io 0x0800-0x080f]
[ 0.095543] pnp 00:04: [io 0x1000-0x107f]
[ 0.095546] pnp 00:04: [io 0x1180-0x11bf]
[ 0.095548] pnp 00:04: [mem 0xe0000000-0xefffffff]
[ 0.095551] pnp 00:04: [mem 0xf0000000-0xf0003fff]
[ 0.095554] pnp 00:04: [mem 0xf0004000-0xf0004fff]
[ 0.095556] pnp 00:04: [mem 0xf0005000-0xf0005fff]
[ 0.095559] pnp 00:04: [mem 0xf0008000-0xf000bfff]
[ 0.095561] pnp 00:04: [mem 0xfed20000-0xfed8ffff]
[ 0.095635] system 00:04: [io 0x0200-0x020f] has been reserved
[ 0.095639] system 00:04: [io 0x0800-0x080f] has been reserved
[ 0.095642] system 00:04: [io 0x1000-0x107f] has been reserved
[ 0.095646] system 00:04: [io 0x1180-0x11bf] has been reserved
[ 0.095650] system 00:04: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.095653] system 00:04: [mem 0xf0000000-0xf0003fff] has been reserved
[ 0.095657] system 00:04: [mem 0xf0004000-0xf0004fff] has been reserved
[ 0.095661] system 00:04: [mem 0xf0005000-0xf0005fff] has been reserved
[ 0.095665] system 00:04: [mem 0xf0008000-0xf000bfff] has been reserved
[ 0.095669] system 00:04: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.095672] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.095713] pnp 00:05: [io 0x0070-0x0077]
[ 0.095753] pnp 00:05: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.095767] pnp 00:06: [io 0x0060]
[ 0.095769] pnp 00:06: [io 0x0064]
[ 0.095775] pnp 00:06: [irq 1]
[ 0.095820] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.095833] pnp 00:07: [irq 12]
[ 0.095880] pnp 00:07: Plug and Play ACPI device, IDs AUI1501 PNP0f13
(active)
[ 0.095897] pnp: PnP ACPI: found 8 devices
[ 0.095899] ACPI: ACPI bus type pnp unregistered
[ 0.095902] PnPBIOS: Disabled by ACPI PNP
[ 0.132581] PCI: max bus depth: 2 pci_try_num: 3
[ 0.132623] pci 0000:00:1e.0: BAR 15: assigned [mem
0x80000000-0x83ffffff pref]
[ 0.132628] pci 0000:00:1c.0: BAR 14: assigned [mem
0x84000000-0x841fffff]
[ 0.132632] pci 0000:00:1c.0: BAR 15: assigned [mem
0x84200000-0x843fffff 64bit pref]
[ 0.132638] pci 0000:00:1c.0: BAR 13: assigned [io 0x5000-0x5fff]
[ 0.132642] pci 0000:01:00.0: BAR 6: assigned [mem 0xc8120000-0xc813ffff
pref]
[ 0.132646] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.132649] pci 0000:00:01.0: bridge window [io 0x3000-0x3fff]
[ 0.132653] pci 0000:00:01.0: bridge window [mem 0xc8100000-0xc81fffff]
[ 0.132657] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xd7ffffff
pref]
[ 0.132662] pci 0000:00:1c.0: PCI bridge to [bus 02-02]
[ 0.132666] pci 0000:00:1c.0: bridge window [io 0x5000-0x5fff]
[ 0.132673] pci 0000:00:1c.0: bridge window [mem 0x84000000-0x841fffff]
[ 0.132678] pci 0000:00:1c.0: bridge window [mem 0x84200000-0x843fffff
64bit pref]
[ 0.132690] pci 0000:06:06.0: BAR 16: assigned [mem
0x88000000-0x8bffffff]
[ 0.132694] pci 0000:06:06.0: BAR 15: assigned [mem
0x80000000-0x83ffffff pref]
[ 0.132697] pci 0000:06:06.0: BAR 14: assigned [io 0x4400-0x44ff]
[ 0.132701] pci 0000:06:06.0: BAR 13: assigned [io 0x4800-0x48ff]
[ 0.132704] pci 0000:06:06.0: CardBus bridge to [bus 07-0a]
[ 0.132706] pci 0000:06:06.0: bridge window [io 0x4800-0x48ff]
[ 0.132713] pci 0000:06:06.0: bridge window [io 0x4400-0x44ff]
[ 0.132720] pci 0000:06:06.0: bridge window [mem 0x80000000-0x83ffffff
pref]
[ 0.132726] pci 0000:06:06.0: bridge window [mem 0x88000000-0x8bffffff]
[ 0.132732] pci 0000:00:1e.0: PCI bridge to [bus 06-07]
[ 0.132736] pci 0000:00:1e.0: bridge window [io 0x4000-0x4fff]
[ 0.132743] pci 0000:00:1e.0: bridge window [mem 0xc8200000-0xc82fffff]
[ 0.132749] pci 0000:00:1e.0: bridge window [mem 0x80000000-0x83ffffff
pref]
[ 0.132767] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.132771] pci 0000:00:01.0: setting latency timer to 64
[ 0.132778] pci 0000:00:1c.0: enabling device (0000 -> 0003)
[ 0.132785] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.132792] pci 0000:00:1c.0: setting latency timer to 64
[ 0.132800] pci 0000:00:1e.0: setting latency timer to 64
[ 0.132812] pci 0000:06:06.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 0.132819] pci 0000:06:06.0: setting latency timer to 64
[ 0.132824] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.132827] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff]
[ 0.132830] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
[ 0.132832] pci_bus 0000:01: resource 1 [mem 0xc8100000-0xc81fffff]
[ 0.132835] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xd7ffffff pref]
[ 0.132838] pci_bus 0000:02: resource 0 [io 0x5000-0x5fff]
[ 0.132841] pci_bus 0000:02: resource 1 [mem 0x84000000-0x841fffff]
[ 0.132844] pci_bus 0000:02: resource 2 [mem 0x84200000-0x843fffff 64bit
pref]
[ 0.132847] pci_bus 0000:06: resource 0 [io 0x4000-0x4fff]
[ 0.132850] pci_bus 0000:06: resource 1 [mem 0xc8200000-0xc82fffff]
[ 0.132853] pci_bus 0000:06: resource 2 [mem 0x80000000-0x83ffffff pref]
[ 0.132856] pci_bus 0000:06: resource 4 [io 0x0000-0xffff]
[ 0.132859] pci_bus 0000:06: resource 5 [mem 0x00000000-0xffffffff]
[ 0.132862] pci_bus 0000:07: resource 0 [io 0x4800-0x48ff]
[ 0.132865] pci_bus 0000:07: resource 1 [io 0x4400-0x44ff]
[ 0.132867] pci_bus 0000:07: resource 2 [mem 0x80000000-0x83ffffff pref]
[ 0.132870] pci_bus 0000:07: resource 3 [mem 0x88000000-0x8bffffff]
[ 0.132907] NET: Registered protocol family 2
[ 0.132979] IP route cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.133214] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.134021] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.134594] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.134597] TCP reno registered
[ 0.134603] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.134623] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.134777] NET: Registered protocol family 1
[ 0.134832] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.134853] pci 0000:00:1d.0: PCI INT A disabled
[ 0.134866] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.134884] pci 0000:00:1d.1: PCI INT B disabled
[ 0.134895] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.134914] pci 0000:00:1d.2: PCI INT C disabled
[ 0.134922] pci 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.134940] pci 0000:00:1d.3: PCI INT D disabled
[ 0.134949] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.134981] pci 0000:00:1d.7: PCI INT A disabled
[ 0.135004] pci 0000:01:00.0: Boot video device
[ 0.135027] PCI: CLS 32 bytes, default 64
[ 0.135109] Unpacking initramfs...
[ 0.556802] Freeing initrd memory: 12728k freed
[ 0.567041] Simple Boot Flag at 0x36 set to 0x1
[ 0.567498] audit: initializing netlink socket (disabled)
[ 0.567516] type=2000 audit(1344849730.564:1): initialized
[ 0.592710] highmem bounce pool size: 64 pages
[ 0.592717] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.604839] VFS: Disk quotas dquot_6.5.2
[ 0.604879] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.604962] msgmni has been set to 1735
[ 0.605138] alg: No test for stdrng (krng)
[ 0.605167] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 0.605170] io scheduler noop registered
[ 0.605172] io scheduler deadline registered
[ 0.605181] io scheduler cfq registered (default)
[ 0.605276] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.605310] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.605367] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.605417] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.605520] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.605550] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.605552] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.605711] acpiphp: Slot [1] registered
[ 0.605852] intel_idle: does not run on family 6 model 13
[ 0.605880] ERST: Table is not found!
[ 0.605882] GHES: HEST is not enabled!
[ 0.605896] isapnp: Scanning for PnP cards...
[ 0.960098] isapnp: No Plug & Play device found
[ 0.960166] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.960550] serial 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ
20
[ 0.960583] serial 0000:00:1e.3: PCI INT B disabled
[ 0.960676] Linux agpgart interface v0.103
[ 0.960963] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 0.966259] i8042: Detected active multiplexing controller, rev 1.1
[ 0.969343] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.969351] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.969386] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.969418] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.969449] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.969576] mousedev: PS/2 mouse device common for all mice
[ 0.969636] rtc_cmos 00:05: RTC can wake from S4
[ 0.969752] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 0.969783] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.969795] cpuidle: using governor ladder
[ 0.969797] cpuidle: using governor menu
[ 0.970005] TCP cubic registered
[ 0.970032] NET: Registered protocol family 10
[ 0.970540] Mobile IPv6
[ 0.970543] NET: Registered protocol family 17
[ 0.970547] Registering the dns_resolver key type
[ 0.970567] Using IPI No-Shortcut mode
[ 0.970659] PM: Hibernation image not present or could not be loaded.
[ 0.970672] registered taskstats version 1
[ 0.977274] rtc_cmos 00:05: setting system clock to 2012-08-13 09:22:11
UTC (1344849731)
[ 0.977332] Initializing network drop monitor service
[ 0.977474] Freeing unused kernel memory: 412k freed
[ 0.977663] Write protecting the kernel text: 2840k
[ 0.977696] Write protecting the kernel read-only data: 1088k
[ 0.977698] NX-protecting the kernel data: 3304k
[ 0.991760] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input0
[ 0.992289] udevd[44]: starting version 175
[ 1.070043] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22,
2004)
[ 1.070072] 8139cp 0000:06:07.0: This (id 10ec:8139 rev 10) is not an
8139C+ compatible chip, use 8139too
[ 1.070469] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.070503] 8139too 0000:06:07.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 1.071910] 8139too 0000:06:07.0: eth0: RealTek RTL8139 at 0x4000,
00:16:d3:92:ec:f6, IRQ 20
[ 1.093891] usbcore: registered new interface driver usbfs
[ 1.093919] usbcore: registered new interface driver hub
[ 1.111400] firewire_ohci 0000:06:06.2: PCI INT C -> GSI 21 (level, low)
-> IRQ 21
[ 1.111555] sdhci: Secure Digital Host Controller Interface driver
[ 1.111558] sdhci: Copyright(c) Pierre Ossman
[ 1.113619] usbcore: registered new device driver usb
[ 1.114113] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.114142] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) ->
IRQ 23
[ 1.114162] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.114166] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.114193] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus
number 1
[ 1.114226] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.118124] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.130794] SCSI subsystem initialized
[ 1.142678] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.142682] ACPI: Thermal Zone [THR0] (70 C)
[ 1.147403] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.150130] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.150134] ACPI: Thermal Zone [THR1] (62 C)
[ 1.156374] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xc8000000
[ 1.164112] firewire_ohci: Added fw-ohci device 0000:06:06.2, OHCI
v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 1.164306] sdhci-pci 0000:06:06.4: SDHCI controller found [104c:8034]
(rev 0)
[ 1.164325] sdhci-pci 0000:06:06.4: PCI INT A -> GSI 22 (level, low) ->
IRQ 22
[ 1.164376] mmc0: no vmmc regulator found
[ 1.164413] Registered led device: mmc0::
[ 1.165588] mmc0: SDHCI controller on PCI [0000:06:06.4] using PIO
[ 1.165610] mmc1: no vmmc regulator found
[ 1.165641] Registered led device: mmc1::
[ 1.166671] mmc1: SDHCI controller on PCI [0000:06:06.4] using PIO
[ 1.166691] mmc2: no vmmc regulator found
[ 1.166719] Registered led device: mmc2::
[ 1.167749] mmc2: SDHCI controller on PCI [0000:06:06.4] using PIO
[ 1.170620] libata version 3.00 loaded.
[ 1.192241] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.192272] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.192276] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.192279] usb usb1: Product: EHCI Host Controller
[ 1.192281] usb usb1: Manufacturer: Linux 3.2.0-3-686-pae ehci_hcd
[ 1.192284] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.192415] hub 1-0:1.0: USB hub found
[ 1.192421] hub 1-0:1.0: 8 ports detected
[ 1.193028] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) ->
IRQ 23
[ 1.193041] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.193046] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.193058] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus
number 2
[ 1.193090] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[ 1.193127] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.193130] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.193133] usb usb2: Product: UHCI Host Controller
[ 1.193136] usb usb2: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.193138] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.193364] hub 2-0:1.0: USB hub found
[ 1.193369] hub 2-0:1.0: 2 ports detected
[ 1.193445] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) ->
IRQ 19
[ 1.193455] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.193459] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.193466] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus
number 3
[ 1.193508] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[ 1.193544] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.193547] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.193550] usb usb3: Product: UHCI Host Controller
[ 1.193552] usb usb3: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.193555] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.193674] hub 3-0:1.0: USB hub found
[ 1.193678] hub 3-0:1.0: 2 ports detected
[ 1.193749] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) ->
IRQ 18
[ 1.193757] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.193761] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.193770] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus
number 4
[ 1.193807] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[ 1.193842] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.193845] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.193848] usb usb4: Product: UHCI Host Controller
[ 1.193850] usb usb4: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.193853] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.193961] hub 4-0:1.0: USB hub found
[ 1.193965] hub 4-0:1.0: 2 ports detected
[ 1.194035] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) ->
IRQ 16
[ 1.194044] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.194048] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.194055] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus
number 5
[ 1.194093] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[ 1.194129] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.194133] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.194135] usb usb5: Product: UHCI Host Controller
[ 1.194138] usb usb5: Manufacturer: Linux 3.2.0-3-686-pae uhci_hcd
[ 1.194140] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.194247] hub 5-0:1.0: USB hub found
[ 1.194253] hub 5-0:1.0: 2 ports detected
[ 1.194328] ata_piix 0000:00:1f.1: version 2.13
[ 1.194339] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) ->
IRQ 18
[ 1.194377] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 1.207476] scsi0 : ata_piix
[ 1.208805] scsi1 : ata_piix
[ 1.209318] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x18c0 irq
14
[ 1.209322] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18c8 irq
15
[ 1.209756] ata2: port disabled--ignoring
[ 1.380526] ata1.00: ATA-8: INTEL SSDSA2CW080G3, 4PC10362, max UDMA/133
[ 1.380530] ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/1)
[ 1.392538] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 1.405907] ata1.01: ATA-8: WDC WD3200BEVE-00A0HT0, 11.01A11, max
UDMA/100
[ 1.405911] ata1.01: 625142448 sectors, multi 16: LBA48
[ 1.421331] ata1.00: configured for UDMA/100
[ 1.437320] ata1.01: configured for UDMA/100
[ 1.437446] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW08
4PC1 PQ: 0 ANSI: 5
[ 1.437758] scsi 0:0:1:0: Direct-Access ATA WDC WD3200BEVE-0
11.0 PQ: 0 ANSI: 5
[ 1.445599] sd 0:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0
GB/74.5 GiB)
[ 1.445672] sd 0:0:0:0: [sda] Write Protect is off
[ 1.445676] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.445699] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.446483] sda: sda1
[ 1.446774] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.446804] sd 0:0:1:0: [sdb] 625142448 512-byte logical blocks: (320
GB/298 GiB)
[ 1.446855] sd 0:0:1:0: [sdb] Write Protect is off
[ 1.446858] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.446881] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.480402] sdb: sdb1 sdb2 < sdb5 >
[ 1.481181] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 1.564020] Refined TSC clocksource calibration: 1995.596 MHz.
[ 1.564027] Switching to clocksource tsc
[ 1.592460] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 1.664097] firewire_core: created device fw0: GUID 07e40a0093985009,
S400
[ 1.792528] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 1.992464] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 2.236020] EXT4-fs (sda1): mounted filesystem with ordered data mode.
Opts: (null)
[ 2.515555] udevd[273]: starting version 175
[ 2.634690] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[ 2.636618] ACPI: Requesting acpi_cpufreq
[ 2.636695] ACPI: Lid Switch [LID0]
[ 2.636768] input: Sleep Button as
/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[ 2.636775] ACPI: Sleep Button [SLPB]
[ 2.636833] input: Power Button as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[ 2.636837] ACPI: Power Button [PWB]
[ 2.651523] Marking TSC unstable due to TSC halts in idle
[ 2.651546] ACPI: acpi_idle registered with cpuidle
[ 2.652057] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 2.652065] ACPI: Power Button [PWRF]
[ 2.662201] Switching to clocksource hpet
[ 2.671851] wmi: Mapper loaded
[ 2.719005] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/LNXVIDEO:00/input/input5
[ 2.719015] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 2.733659] ACPI: AC Adapter [AC] (on-line)
[ 2.767445] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) ->
IRQ 19
[ 2.767452] ACPI: resource 0000:00:1f.3 [io 0x18e0-0x18ff] conflicts
with ACPI region SMBI [io 0x18e0-0x18ef]
[ 2.767456] ACPI: If an ACPI driver is available for this device, you
should use it instead of the native driver
[ 2.770380] ACPI: Battery Slot [BAT0] (battery present)
[ 2.777358] yenta_cardbus 0000:06:06.0: CardBus bridge found [103c:309d]
[ 2.777384] yenta_cardbus 0000:06:06.0: Enabling burst memory read
transactions
[ 2.777390] yenta_cardbus 0000:06:06.0: Using CSCINT to route CSC
interrupts to PCI
[ 2.777393] yenta_cardbus 0000:06:06.0: Routing CardBus interrupts to PCI
[ 2.777399] yenta_cardbus 0000:06:06.0: TI: mfunc 0x01aa1b02, devctl 0x64
[ 2.777606] intel_rng: FWH not detected
[ 2.782336] iTCO_vendor_support: vendor-support=0
[ 2.786122] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[ 2.786220] iTCO_wdt: Found a ICH6-M TCO device (Version=2,
TCOBASE=0x1060)
[ 2.786285] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 2.791248] cfg80211: Calling CRDA to update world regulatory domain
[ 2.796350] [drm] Initialized drm 1.1.0 20060810
[ 2.796869] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 2.806052] lib80211: common routines for IEEE802.11 drivers
[ 2.806056] lib80211_crypt: registered algorithm 'NULL'
[ 2.810528] libipw: 802.11 data/management/control stack, git-1.1.13
[ 2.810531] libipw: Copyright (C) 2004-2005 Intel Corporation <
jketreno@linux.intel.com>
[ 2.819095] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
1.2.2kmprq
[ 2.819098] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 2.880413] [drm] radeon kernel modesetting enabled.
[ 2.880541] radeon 0000:01:00.0: power state changed by ACPI to D0
[ 2.880546] radeon 0000:01:00.0: power state changed by ACPI to D0
[ 2.880555] radeon 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ
16
[ 2.880562] radeon 0000:01:00.0: setting latency timer to 64
[ 2.880724] [drm] initializing kernel modesetting (RV410 0x1002:0x5653
0x103C:0x309E).
[ 2.880745] [drm] register mmio base: 0xC8100000
[ 2.880747] [drm] register mmio size: 65536
[ 2.880935] ATOM BIOS: HP
[ 2.880957] [drm] Generation 2 PCI interface, using max accessible memory
[ 2.880962] radeon 0000:01:00.0: VRAM: 128M 0x00000000D0000000 -
0x00000000D7FFFFFF (128M used)
[ 2.880966] radeon 0000:01:00.0: GTT: 512M 0x00000000B0000000 -
0x00000000CFFFFFFF
[ 2.880980] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.880982] [drm] Driver supports precise vblank timestamp query.
[ 2.881022] radeon 0000:01:00.0: irq 42 for MSI/MSI-X
[ 2.881028] radeon 0000:01:00.0: radeon: using MSI.
[ 2.881051] [drm] radeon: irq initialized.
[ 2.890123] [drm] Detected VRAM RAM=128M, BAR=128M
[ 2.890126] [drm] RAM width 128bits DDR
[ 2.901092] [TTM] Zone kernel: Available graphics memory: 444380 kiB.
[ 2.901096] [TTM] Zone highmem: Available graphics memory: 1036704 kiB.
[ 2.901099] [TTM] Initializing pool allocator.
[ 2.901126] [drm] radeon: 128M of VRAM memory ready
[ 2.901129] [drm] radeon: 512M of GTT memory ready.
[ 2.901153] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 2.903881] [drm] PCIE GART of 512M enabled (table at
0x00000000D0040000).
[ 2.903893] [drm] radeon: 2 quad pipes, 1 z pipes initialized.
[ 2.903930] radeon 0000:01:00.0: WB enabled
[ 2.930062] [drm] Loading R400 Microcode
[ 2.930934] input: HP WMI hotkeys as /devices/virtual/input/input7
[ 2.992538] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 3.008993] yenta_cardbus 0000:06:06.0: ISA IRQ mask 0x0cf8, PCI irq 22
[ 3.008998] yenta_cardbus 0000:06:06.0: Socket status: 30000006
[ 3.009003] pci_bus 0000:06: Raising subordinate bus# of parent bus
(#06) from #07 to #0a
[ 3.009014] yenta_cardbus 0000:06:06.0: pcmcia: parent PCI bridge
window: [io 0x4000-0x4fff]
[ 3.009017] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x4000-0x4fff:
[ 3.010130] [drm] radeon: ring at 0x00000000B0001000
[ 3.010151] [drm] ring test succeeded in 1 usecs
[ 3.010313] [drm] radeon: ib pool ready.
[ 3.010880] [drm] ib test succeeded in 0 usecs
[ 3.011411] [drm] Radeon Display Connectors
[ 3.011414] [drm] Connector 0:
[ 3.011416] [drm] VGA
[ 3.011420] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 3.011422] [drm] Encoders:
[ 3.011424] [drm] CRT1: INTERNAL_DAC1
[ 3.011427] [drm] Connector 1:
[ 3.011428] [drm] LVDS
[ 3.011431] [drm] DDC: 0x68 0x68 0x68 0x68 0x68 0x68 0x68 0x68
[ 3.011434] [drm] Encoders:
[ 3.011436] [drm] LCD1: INTERNAL_LVDS
[ 3.011438] [drm] Connector 2:
[ 3.011440] [drm] S-video
[ 3.011442] [drm] Encoders:
[ 3.011444] [drm] TV1: INTERNAL_DAC2
[ 3.011461] [drm] radeon: power management initialized
[ 3.310025] atkbd serio0: Spurious NAK on isa0060/serio0. Some program
might be trying access hardware directly.
[ 3.314811] excluding 0x4000-0x40ff 0x4400-0x44ff 0x4800-0x48ff
[ 3.335796] yenta_cardbus 0000:06:06.0: pcmcia: parent PCI bridge
window: [mem 0xc8200000-0xc82fffff]
[ 3.335801] pcmcia_socket pcmcia_socket0: cs: memory probe
0xc8200000-0xc82fffff: excluding 0xc8200000-0xc820ffff
[ 3.335821] yenta_cardbus 0000:06:06.0: pcmcia: parent PCI bridge
window: [mem 0x80000000-0x83ffffff pref]
[ 3.335825] pcmcia_socket pcmcia_socket0: cs: memory probe
0x80000000-0x83ffffff: excluding 0x80000000-0x83ffffff
[ 3.341417] ipw2200 0000:06:05.0: PCI INT A -> GSI 20 (level, low) ->
IRQ 20
[ 3.341447] ipw2200: Detected Intel PRO/Wireless 2200BG Network
Connection
[ 3.350502] cfg80211: World regulatory domain updated:
[ 3.350506] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp)
[ 3.350510] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 3.350513] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300
mBi, 2000 mBm)
[ 3.350516] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300
mBi, 2000 mBm)
[ 3.350519] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 3.350523] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300
mBi, 2000 mBm)
[ 3.358949] snd_intel8x0 0000:00:1e.2: PCI INT A -> GSI 17 (level, low)
-> IRQ 17
[ 3.359059] snd_intel8x0 0000:00:1e.2: setting latency timer to 64
[ 3.414047] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af:
excluding 0x170-0x177 0x1f0-0x1f7 0x200-0x20f 0x370-0x377
[ 3.415994] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff:
excluding 0x3f0-0x3f7 0x4d0-0x4d7
[ 3.417071] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff:
clean.
[ 3.420060] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7:
clean.
[ 3.420992] pcmcia_socket pcmcia_socket0: cs: memory probe
0x0c0000-0x0fffff: excluding 0xc0000-0xcffff 0xdc000-0xfffff
[ 3.421025] pcmcia_socket pcmcia_socket0: cs: memory probe
0xa0000000-0xa0ffffff: clean.
[ 3.421059] pcmcia_socket pcmcia_socket0: cs: memory probe
0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
[ 3.421089] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff:
clean.
[ 3.546082] ipw2200: Radio Frequency Kill Switch is On:
[ 3.546084] Kill switch must be turned off for wireless networking to
work.
[ 3.549731] cfg80211: failed to add phy80211 symlink to netdev!
[ 3.550072] ipw2200: Detected geography ZZM (11 802.11bg channels, 0
802.11a channels)
[ 3.550105] tifm_7xx1 0000:06:06.3: PCI INT A -> GSI 22 (level, low) ->
IRQ 22
[ 3.651485] [drm] fb mappable at 0xD00C0000
[ 3.651489] [drm] vram apper at 0xD0000000
[ 3.651491] [drm] size 4096000
[ 3.651492] [drm] fb depth is 24
[ 3.651494] [drm] pitch is 5120
[ 3.652276] fbcon: radeondrmfb (fb0) is primary device
[ 4.240502] Console: switching to colour frame buffer device 160x50
[ 4.253399] fb0: radeondrmfb frame buffer device
[ 4.253403] drm: registered panic notifier
[ 4.253430] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:00.0 on
minor 0
[ 4.564056] intel8x0_measure_ac97_clock: measured 55182 usecs (2659
samples)
[ 4.564064] intel8x0: clocking to 48000
[ 4.566811] snd_intel8x0m 0000:00:1e.3: PCI INT B -> GSI 20 (level, low)
-> IRQ 20
[ 4.566842] snd_intel8x0m 0000:00:1e.3: setting latency timer to 64
[ 4.689782] Adding 2650688k swap on /dev/sdb5. Priority:-1 extents:1
across:2650688k
[ 4.701979] EXT4-fs (sda1): re-mounted. Opts: (null)
[ 4.753711] EXT4-fs (sda1): re-mounted. Opts:
errors=remount-ro,commit=600
[ 4.789849] loop: module loaded
[ 4.852269] input: PS/2 Mouse as
/devices/platform/i8042/serio4/input/input8
[ 4.872577] input: AlpsPS/2 ALPS GlidePoint as
/devices/platform/i8042/serio4/input/input9
[ 5.710712] EXT4-fs (sdb1): mounted filesystem with ordered data mode.
Opts: errors=remount-ro
[ 6.024504] RPC: Registered named UNIX socket transport module.
[ 6.024508] RPC: Registered udp transport module.
[ 6.024510] RPC: Registered tcp transport module.
[ 6.024512] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 6.032946] FS-Cache: Loaded
[ 6.052483] FS-Cache: Netfs 'nfs' registered for caching
[ 6.064252] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 6.919374] 8139too 0000:06:07.0: eth0: link up, 100Mbps, full-duplex,
lpa 0x45E1
[ 7.999779] input: ACPI Virtual Keyboard Device as
/devices/virtual/input/input10
[ 9.069848] microcode: CPU0 sig=0x6d8, pf=0x20, revision=0x20
[ 9.084844] microcode: Microcode Update Driver: v2.00 <
tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 14.976231] fuse init (API version 7.17)
 

Thread Tools




All times are GMT. The time now is 02:41 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org