Package: linux-image-2.6.24-1-686
Version: 2.6.24-5
Severity: normal

Hi,

my /etc/modprobe.conf says:

alias pcspkr off

but

$ lsmod | grep pcspkr
pcspkr 3200 0

which creats stupid noisy sounds in several circumstances on my
laptop which I successfully prevented with all previous kernel
versions that were contained in the last two years.

I set the severity to normal, because this might or might not
happen to other modules that should be excluded. For instance
I observed that ipv6 is loaded as well even if I intended to suppress
this module in the same manner as above. Other modules I tried
to suppress (for instance parport) are not loaded.

I fail to see a reason why this kernel behaves different from all
the former ones.

Kind regards and thanks for maintaining Debian Linux kernel

Andreas.


-- Package-specific info:
** Version:
Linux version 2.6.24-1-686 (Debian 2.6.24-5) (waldi@debian.org) (gcc version 4.1.3 20080308 (prerelease) (Debian 4.1.2-21)) #1 SMP Thu Mar 27 17:45:04 UTC 2008

** Command line:
root=/dev/mapper/sputnik-root ro priority=medium

** Not tainted

** Kernel log:
PM: Writing back config space on device 0000:00:1c.1 at offset 7 (was 0, writing 200000f0)
PM: Writing back config space on device 0000:00:1c.1 at offset 6 (was 0, writing c0c00)
PM: Writing back config space on device 0000:00:1c.1 at offset 3 (was 810000, writing 810010)
PM: Writing back config space on device 0000:00:1c.1 at offset 1 (was 100000, writing 100507)
PCI: Setting latency timer of device 0000:00:1c.1 to 64
PM: Writing back config space on device 0000:00:1c.2 at offset f (was 300, writing 20300)
PM: Writing back config space on device 0000:00:1c.2 at offset 9 (was 10001, writing 1fff1)
PM: Writing back config space on device 0000:00:1c.2 at offset 8 (was 0, writing dfc0dfc0)
PM: Writing back config space on device 0000:00:1c.2 at offset 7 (was 0, writing 200000f0)
PM: Writing back config space on device 0000:00:1c.2 at offset 6 (was 0, writing 90900)
PM: Writing back config space on device 0000:00:1c.2 at offset 3 (was 810000, writing 810010)
PM: Writing back config space on device 0000:00:1c.2 at offset 1 (was 100000, writing 100407)
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.1 to 64
PM: Writing back config space on device 0000:00:1d.1 at offset f (was 200, writing 20a)
usb usb2: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 22 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.2 to 64
PM: Writing back config space on device 0000:00:1d.2 at offset f (was 300, writing 305)
usb usb3: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 22
PCI: Setting latency timer of device 0000:00:1d.3 to 64
PM: Writing back config space on device 0000:00:1d.3 at offset f (was 400, writing 403)
usb usb4: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
PM: Writing back config space on device 0000:00:1e.0 at offset 9 (was 100f1, writing 1fff1)
PM: Writing back config space on device 0000:00:1e.0 at offset 8 (was f0, writing fff0)
PM: Writing back config space on device 0000:00:1e.0 at offset 7 (was 2280e0f0, writing 228000f0)
PM: Writing back config space on device 0000:00:1e.0 at offset 6 (was 20030300, writing 20070300)
PM: Writing back config space on device 0000:00:1e.0 at offset 1 (was 100007, writing 100107)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PM: Writing back config space on device 0000:00:1f.0 at offset 1 (was 2100007, writing 2100107)
PM: Writing back config space on device 0000:00:1f.2 at offset f (was 200, writing 20b)
ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
PM: Writing back config space on device 0000:00:1f.3 at offset f (was 200, writing 20b)
ata1.00: _GTF evaluation failed (AE 0x1001)
ata1.01: _GTF evaluation failed (AE 0x1001)
PM: Writing back config space on device 0000:00:1f.3 at offset 1 (was 2800001, writing 2800101)
PM: Writing back config space on device 0000:0c:00.0 at offset f (was 100, writing 10b)
ata2.01: _GTF evaluation failed (AE 0x1001)
PM: Writing back config space on device 0000:0c:00.0 at offset 4 (was 0, writing dfdff000)
PM: Writing back config space on device 0000:0c:00.0 at offset 3 (was 0, writing 10)
PM: Writing back config space on device 0000:0c:00.0 at offset 1 (was 100000, writing 100102)
PM: Writing back config space on device 0000:09:00.0 at offset c (was 0, writing 78850000)
PM: Writing back config space on device 0000:09:00.0 at offset 3 (was 0, writing 10)
PM: Writing back config space on device 0000:09:00.0 at offset 1 (was 100000, writing 100102)
PM: Writing back config space on device 0000:03:01.0 at offset f (was 800100, writing 58001ff)
PM: Writing back config space on device 0000:03:01.0 at offset e (was 1, writing 18fd)
PM: Writing back config space on device 0000:03:01.0 at offset d (was 1, writing 1801)
PM: Writing back config space on device 0000:03:01.0 at offset c (was 1, writing 14fd)
PM: Writing back config space on device 0000:03:01.0 at offset b (was 1, writing 1401)
PM: Writing back config space on device 0000:03:01.0 at offset a (was 0, writing 8ffff000)
PM: Writing back config space on device 0000:03:01.0 at offset 9 (was 0, writing 8c000000)
PM: Writing back config space on device 0000:03:01.0 at offset 8 (was 0, writing 8bfff000)
PM: Writing back config space on device 0000:03:01.0 at offset 7 (was 0, writing 88000000)
PM: Writing back config space on device 0000:03:01.0 at offset 6 (was 20000000, writing b0070403)
PM: Writing back config space on device 0000:03:01.0 at offset 4 (was 0, writing 90000000)
PM: Writing back config space on device 0000:03:01.0 at offset 3 (was 24000, writing 2a800)
PM: Writing back config space on device 0000:03:01.0 at offset 1 (was 4100007, writing 4100087)
Yenta O2: res at 0x94/0xD4: 00/ea
Yenta O2: enabling read prefetch/write burst
serial 00:0b: activated
parport_pc 00:0c: activated
ata1.00: configured for UDMA/100
sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] Starting disk
Restarting tasks ... <6>usb 1-2: USB disconnect, address 4
usb 1-2.3: USB disconnect, address 5
usb 1-2.3.2: USB disconnect, address 6
done.
tg3.c:v3.86 (November 9, 2007)
ACPI: PCI Interrupt 0000:09:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:09:00.0 to 64
eth0: Tigon3 [partno(BCM5752KFBG) rev 6002 PHY(5752)] (PCI Express) 10/100/1000Base-T Ethernet 00:15:c5:52:73:08
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000] dma_mask[64-bit]
ADDRCONF(NETDEV_UP): eth0: link is not ready
input: Lid Switch as /class/input/input10
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input11
ACPI: Power Button (CM) [PBTN]
input: Sleep Button (CM) as /class/input/input12
ACPI: Sleep Button (CM) [SBTN]
ACPI: Thermal Zone [THM] (29 C)
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery present)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present

** Loaded modules:
Module Size Used by
sbs 14376 0
sbshc 6848 1 sbs
battery 13572 0
ac 6116 0
thermal 16028 0
fan 4772 0
button 8432 0
tg3 88964 0
i915 22048 1
drm 74132 2 i915
rfcomm 36784 2
l2cap 22880 9 rfcomm
bluetooth 53636 4 rfcomm,l2cap
irtty_sir 8096 0
sir_dev 15460 1 irtty_sir
irda 174236 2 irtty_sir,sir_dev
crc_ccitt 2176 1 irda
ipv6 240836 18
acpi_cpufreq 9260 1
cpufreq_conservative 7560 0
cpufreq_ondemand 8492 1
cpufreq_userspace 4260 0
cpufreq_stats 5184 0
cpufreq_powersave 1856 0
freq_table 4512 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
loop 16804 0
joydev 11360 0
serio_raw 6660 0
yenta_socket 24844 0
parport_pc 33668 0
rsrc_nonstatic 11872 1 yenta_socket
pcmcia_core 36884 2 yenta_socket,rsrc_nonstatic
i2c_i801 9232 0
rtc_cmos 8352 0
rtc_core 17992 1 rtc_cmos
parport 34280 1 parport_pc
psmouse 36464 0
rtc_lib 3040 1 rtc_core
snd_hda_intel 275264 2
iwl3945 84712 0
pcspkr 3200 0
snd_pcm 71780 1 snd_hda_intel
iTCO_wdt 11268 0
snd_timer 21092 1 snd_pcm
firmware_class 9312 1 iwl3945
snd 48612 7 snd_hda_intel,snd_pcm,snd_timer
intelfb 34980 0
mac80211 114380 1 iwl3945
soundcore 7552 1 snd
i2c_algo_bit 5956 1 intelfb
intel_agp 23412 1
snd_page_alloc 10056 2 snd_hda_intel,snd_pcm
video 18672 0
output 3744 1 video
agpgart 31688 4 drm,intelfb,intel_agp
i2c_core 22432 3 i2c_i801,intelfb,i2c_algo_bit
cfg80211 13480 1 mac80211
evdev 11104 8
ext3 122888 6
jbd 43732 1 ext3
mbcache 8288 1 ext3
sha256_generic 11040 0
aes_generic 27776 0
aes_i586 33376 2
geode_aes 6024 0
cbc 4416 1
blkcipher 6724 2 geode_aes,cbc
dm_crypt 13220 1
dm_mirror 21600 0
dm_snapshot 16964 0
dm_mod 55812 18 dm_crypt,dm_mirror,dm_snapshot
sd_mod 27200 3
ata_piix 17092 2
ata_generic 7428 0
libata 144464 2 ata_piix,ata_generic
scsi_mod 141164 2 sd_mod,libata
generic 4388 0 [permanent]
ide_core 108292 1 generic
ehci_hcd 32524 0
uhci_hcd 23376 0
usbcore 132940 3 ehci_hcd,uhci_hcd
processor 36520 4 thermal,acpi_cpufreq

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at eff8 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
Kernel modules: intelfb

00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>

00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: dfd00000-dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=09, sec-latency=0
Memory behind bridge: dfc00000-dfcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at bf80 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at bf60 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at bf40 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 22
Region 4: I/O ports at bf20 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ffa80000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=03, subordinate=07, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-rng, iTCO_wdt

00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01) (prog-if 80 [Master])
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at bfa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 10c0 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

03:01.0 CardBus bridge [0607]: O2 Micro, Inc. OZ601/6912/711E0 CardBus/SmartCardBus Controller [1217:6972] (rev 40)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 18
Region 0: Memory at 90000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=03, secondary=04, subordinate=07, sec-latency=176
Memory window 0: 88000000-8bfff000 (prefetchable)
Memory window 1: 8c000000-8ffff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket

09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express [14e4:1600] (rev 02)
Subsystem: Dell Unknown device [1028:01c2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 220
Region 0: Memory at dfcf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3

0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation Unknown device [8086:1021]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 17
Region 0: Memory at dfdff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel modules: iwl3945



-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (501, 'testing'), (50, 'unstable'), (5, 'experimental')
Architecture: i386 (i686)

Kernel: Linux 2.6.24-1-686 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-2.6.24-1-686 depends on:
ii debconf [debconf-2.0] 1.5.20 Debian configuration management sy
ii initramfs-tools [linux-initr 0.91e tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.24-1-686 recommends:
ii libc6-i686 2.7-10 GNU C Library: Shared libraries [i

-- debconf information:
linux-image-2.6.24-1-686/preinst/overwriting-modules-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/bootloader-error-2.6.24-1-686:
linux-image-2.6.24-1-686/postinst/create-kimage-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/prerm/would-invalidate-boot-loader-2.6.24-1-686: true
linux-image-2.6.24-1-686/preinst/initrd-2.6.24-1-686:
linux-image-2.6.24-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.24-1-686/preinst/abort-install-2.6.24-1-686:
linux-image-2.6.24-1-686/prerm/removing-running-kernel-2.6.24-1-686: true
linux-image-2.6.24-1-686/preinst/abort-overwrite-2.6.24-1-686:
linux-image-2.6.24-1-686/postinst/bootloader-test-error-2.6.24-1-686:
linux-image-2.6.24-1-686/preinst/lilo-initrd-2.6.24-1-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-1-686/postinst/old-system-map-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/preinst/failed-to-move-modules-2.6.24-1-686:
linux-image-2.6.24-1-686/postinst/depmod-error-initrd-2.6.24-1-686: false
linux-image-2.6.24-1-686/preinst/bootloader-initrd-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/old-initrd-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/old-dir-initrd-link-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/depmod-error-2.6.24-1-686: false
linux-image-2.6.24-1-686/preinst/elilo-initrd-2.6.24-1-686: true
linux-image-2.6.24-1-686/postinst/kimage-is-a-directory:



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org