Package: linux-2.6
Version: 2.6.39-2
Severity: normal


Binary packages that have failed to boot on my Pegasos2 are
linux-image-2.6.39-2-powerpc_2.6.39-2,
linux-image-2.6.39-1-powerpc_2.6.39-1 and
linux-image-2.6.38-2-powerpc_2.6.38-5.

There is nothing interesting on the screen. After loading from firmware
they just stick at one of the characters of a BSD style spinner.

I am running 2.6.32-5-powerpc so this was used to report bug.

As a result I am not able to confirm if bug 627585 has been fixed.

-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
revision : 1.1 (pvr 8002 0101)
platform : CHRP
model : Pegasos2
machine : CHRP Pegasos2

** PCI devices:
0000:00:00.0 Host bridge [0600]: Marvell Technology Group Ltd. MV64360/64361/64362 System Controller [11ab:6460] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR+ INTx-
Latency: 0, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 0

0000:00:01.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044] (rev 46) (prog-if 10 [OHCI])
Subsystem: VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller [1106:3044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (8000ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 80002000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at 1080 [size=128]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci

0000:00:06.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8 (250ns min, 10500ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

0000:00:06.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 8 (250ns min, 10500ns max)
Interrupt: pin B routed to IRQ 9
Region 0: Memory at 80001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

0000:00:06.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: Device [0ee4:3383]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 68 (4000ns min, 8500ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 9
Region 0: Memory at 80002800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

0000:00:0c.0 ISA bridge [0601]: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] [1106:8231] (rev 10)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: parport_pc

0000:00:0c.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin ? routed to IRQ 14
Region 0: [virtual] I/O ports at 1000 [size=8]
Region 1: [virtual] I/O ports at 100c [size=4]
Region 2: [virtual] I/O ports at 1010 [size=8]
Region 3: [virtual] I/O ports at 101c [size=4]
Region 4: I/O ports at 1020 [size=16]
Capabilities: <access denied>
Kernel driver in use: VIA_IDE

0000:00:0c.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1e) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 22
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1040 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd

0000:00:0c.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 1e) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 22
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at 1060 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd

0000:00:0c.4 Bridge [0680]: VIA Technologies, Inc. VT8235 ACPI [1106:8235] (rev 10)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

0000:00:0c.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT82C686 AC97 Audio Controller [1106:3058] (rev 40)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1100 [size=256]
Region 1: I/O ports at 1030 [size=4]
Region 2: I/O ports at 1034 [size=4]
Capabilities: <access denied>
Kernel driver in use: VIA 82xx Audio

0000:00:0c.6 Communication controller [0780]: VIA Technologies, Inc. AC'97 Modem Controller [1106:3068] (rev 20)
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 9
Region 0: I/O ports at 1200 [size=256]
Capabilities: <access denied>

0000:00:0d.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 51)
Subsystem: Device [3065:1106]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (63750ns min, 63750ns max)
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at 1300 [size=256]
Region 1: Memory at 80002900 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine

0001:01:00.0 Host bridge [0600]: Marvell Technology Group Ltd. MV64360/64361/64362 System Controller [11ab:6460] (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 0

0001:01:08.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon 9200 PRO] [1002:5960] (rev 01) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:0054]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (2000ns min)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 1000 [size=256]
Region 2: Memory at c8000000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at c8020000 [disabled] [size=128K]
Kernel driver in use: radeonfb

0001:01:08.1 Display controller [0380]: ATI Technologies Inc RV280 [Radeon 9200 PRO] (Secondary) [1002:5940] (rev 01)
Subsystem: ASUSTeK Computer Inc. Device [1043:0055]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at c8010000 (32-bit, non-prefetchable) [disabled] [size=64K]


** USB devices:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 03f0:3417 Hewlett-Packard LaserJet 3055
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: 6.0.1
APT prefers stable
APT policy: (500, 'stable')
Architecture: powerpc (ppc)

Kernel: Linux 2.6.32-5-powerpc
Locale: LANG=en_AU, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-2.6.39-2-powerpc depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.99 tools for generating an initramfs
ii libc6 2.11.2-10 Embedded GNU C Library: Shared lib
ii linux-base 3.2 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.39-2-powerpc recommends:
ii firmware-linux-free 3 Binary firmware for various driver

Versions of packages linux-image-2.6.39-2-powerpc suggests:
ii linux-doc-2.6.39 2.6.39-2 Linux kernel specific documentatio
ii mkvmlinuz 35 create a kernel to boot a PowerPC

Versions of packages linux-image-2.6.39-2-powerpc is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.30 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)

-- debconf information:
linux-image-2.6.39-2-powerpc/postinst/missing-firmware-2.6.39-2-powerpc:
linux-image-2.6.39-2-powerpc/prerm/removing-running-kernel-2.6.39-2-powerpc: true
linux-image-2.6.39-2-powerpc/postinst/ignoring-ramdisk:
linux-image-2.6.39-2-powerpc/postinst/depmod-error-initrd-2.6.39-2-powerpc: false



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110617222943.2188.34712.reportbug@chrp.ab.bgc.co m.au">http://lists.debian.org/20110617222943.2188.34712.reportbug@chrp.ab.bgc.co m.au

On Sat, 2011-06-18 at 06:29 +0800, Andrew Buckeridge wrote:
> Package: linux-2.6
> Version: 2.6.39-2
> Severity: normal
>
>
> Binary packages that have failed to boot on my Pegasos2 are
> linux-image-2.6.39-2-powerpc_2.6.39-2,
> linux-image-2.6.39-1-powerpc_2.6.39-1 and
> linux-image-2.6.38-2-powerpc_2.6.38-5.
>
> There is nothing interesting on the screen. After loading from firmware
> they just stick at one of the characters of a BSD style spinner.
>
> I am running 2.6.32-5-powerpc so this was used to report bug.
[...]

Can you please use http://snapshot.debian.org/package/linux-2.6/ to find
which was the last working version?

Ben.

--
Ben Hutchings
When in doubt, use brute force. - Ken Thompson

On Mon, 20 Jun 2011 05:49:57 +0100
Ben Hutchings <ben@decadent.org.uk> wrote:

> Can you please use http://snapshot.debian.org/package/linux-2.6/ to find
> which was the last working version?

linux-image-2.6.32-5-powerpc_2.6.32-34squeeze1_powerpc.deb
Quiet see dmesg.0 attached.

linux-image-2.6.32-5-powerpc_2.6.32-35_powerpc.deb
Quiet see dmesg.2 attached.

linux-image-2.6.33-2-powerpc_2.6.33-1~experimental.5_powerpc.deb
Booted, but lots of "event-scan failed". See dmesg.1 attached.

I could not find any powerpc builds between these.

linux-image-2.6.36-trunk-powerpc_2.6.36-1~experimental.1_powerpc.deb
linux-image-2.6.37-1-powerpc_2.6.37-1_powerpc.deb
linux-image-2.6.37-2-powerpc_2.6.37-2_powerpc.deb
These failed to boot. In all cases stuck at the spinner.

Using mkvmlinuz to make loader to boot with CHRP Pegasos2 OF.
>
> Ben.
>
> --
> Ben Hutchings
> When in doubt, use brute force. - Ken Thompson
[ 0.000000] Using CHRP machine description
[ 0.000000] Total memory = 512MB; using 1024kB for hash table (at cff00000)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-powerpc (Debian 2.6.32-34squeeze1) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Thu May 19 00:02:08 UTC 2011
[ 0.000000] Found initrd at 0xc0643000:0xc0f8d79b
[ 0.000000] Found legacy serial port 0 for /pci@80000000/isa@C/serial@i2F8
[ 0.000000] port=2f8, taddr=fe0002f8, irq=0, clk=1843200, speed=0
[ 0.000000] bootconsole [udbg0] enabled
[ 0.000000] chrp type = 6 [Genesi Pegasos]
[ 0.000000] Pegasos l2cr : L2 cache was not active, activating
[ 0.000000] PCI bus 0 controlled by /pci@80000000 at 80000000
[ 0.000000] PCI host bridge /pci@80000000 (primary) ranges:
[ 0.000000] IO 0x00000000fe000000..0x00000000fe00ffff -> 0x0000000000000000
[ 0.000000] MEM 0x0000000080000000..0x00000000bfffffff -> 0x0000000080000000
[ 0.000000] PCI bus 0 controlled by /pci@C0000000 at c0000000
[ 0.000000] PCI host bridge /pci@C0000000 ranges:
[ 0.000000] IO 0x00000000f8000000..0x00000000f800ffff -> 0x0000000000000000
[ 0.000000] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.000000] Top of RAM: 0x20000000, Total RAM: 0x20000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00020000
[ 0.000000] Normal 0x00020000 -> 0x00020000
[ 0.000000] HighMem 0x00020000 -> 0x00020000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c0506328, node_mem_map c0f8e000
[ 0.000000] DMA zone: 1024 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 130048 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: video=radeonfb:1400x1050-8@60 panic=300 root=UUID=39c3b58f-8331-4c14-828b-77eb1c2132df
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] High memory: 0k
[ 0.000000] Memory: 502912k/524288k available (4932k kernel code, 20924k reserved, 276k data, 478k bss, 232k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffef000..0xfffff000 : fixmap
[ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs
[ 0.000000] * 0xff7e0000..0xff800000 : early ioremap
[ 0.000000] * 0xe1000000..0xff7e0000 : vmalloc & ioremap
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512
[ 0.000000] i8259 legacy interrupt controller initialized
[ 0.000000] time_init: decrementer frequency = 33.333333 MHz
[ 0.000000] time_init: processor frequency = 999.999990 MHz
[ 0.000000] clocksource: timebase mult[7800001] shift[22] registered
[ 0.000000] clockevent: decrementer mult[8888887] shift[32] cpu[0]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000379] Security Framework initialized
[ 0.000422] SELinux: Disabled at boot.
[ 0.000449] Mount-cache hash table entries: 512
[ 0.001853] device-tree: Duplicate name in /pci@80000000/usb@C,2/device@1, renamed to "printer@0#1"
[ 0.002448] Initializing cgroup subsys ns
[ 0.002465] Initializing cgroup subsys cpuacct
[ 0.002478] Initializing cgroup subsys devices
[ 0.002490] Initializing cgroup subsys freezer
[ 0.002501] Initializing cgroup subsys net_cls
[ 0.003646] devtmpfs: initialized
[ 0.004801] regulator: core version 0.5
[ 0.005025] NET: Registered protocol family 16
[ 0.008266] MPC7450 family performance monitor hardware support registered
[ 0.008413] PCI: Probing PCI hardware
[ 0.008870] pci 0000:00:01.0: reg 10 32bit mmio: [0x80002000-0x800027ff]
[ 0.008898] pci 0000:00:01.0: reg 14 io port: [0x1080-0x10ff]
[ 0.009073] pci 0000:00:01.0: supports D2
[ 0.009080] pci 0000:00:01.0: PME# supported from D2 D3hot D3cold
[ 0.009102] pci 0000:00:01.0: PME# disabled
[ 0.009267] pci 0000:00:06.0: reg 10 32bit mmio: [0x80000000-0x80000fff]
[ 0.009457] pci 0000:00:06.0: supports D1 D2
[ 0.009463] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot
[ 0.009483] pci 0000:00:06.0: PME# disabled
[ 0.009626] pci 0000:00:06.1: reg 10 32bit mmio: [0x80001000-0x80001fff]
[ 0.009817] pci 0000:00:06.1: supports D1 D2
[ 0.009823] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot
[ 0.009842] pci 0000:00:06.1: PME# disabled
[ 0.009985] pci 0000:00:06.2: reg 10 32bit mmio: [0x80002800-0x800028ff]
[ 0.010176] pci 0000:00:06.2: supports D1 D2
[ 0.010182] pci 0000:00:06.2: PME# supported from D0 D1 D2 D3hot
[ 0.010202] pci 0000:00:06.2: PME# disabled
[ 0.010715] pci 0000:00:0c.1: reg 10 io port: [0x1000-0x1007]
[ 0.010741] pci 0000:00:0c.1: reg 14 io port: [0x100c-0x100f]
[ 0.010767] pci 0000:00:0c.1: reg 18 io port: [0x1010-0x1017]
[ 0.010793] pci 0000:00:0c.1: reg 1c io port: [0x101c-0x101f]
[ 0.010819] pci 0000:00:0c.1: reg 20 io port: [0x1020-0x102f]
[ 0.011159] pci 0000:00:0c.2: reg 20 io port: [0x1040-0x105f]
[ 0.011483] pci 0000:00:0c.3: reg 20 io port: [0x1060-0x107f]
[ 0.012049] pci 0000:00:0c.5: reg 10 io port: [0x1100-0x11ff]
[ 0.012075] pci 0000:00:0c.5: reg 14 io port: [0x1030-0x1033]
[ 0.012101] pci 0000:00:0c.5: reg 18 io port: [0x1034-0x1037]
[ 0.012412] pci 0000:00:0c.6: reg 10 io port: [0x1200-0x12ff]
[ 0.012746] pci 0000:00:0d.0: reg 10 io port: [0x1300-0x13ff]
[ 0.012772] pci 0000:00:0d.0: reg 14 32bit mmio: [0x80002900-0x800029ff]
[ 0.012946] pci 0000:00:0d.0: PME# supported from D0 D3hot D3cold
[ 0.012982] pci 0000:00:0d.0: PME# disabled
[ 0.014577] pci 0001:01:08.0: reg 10 32bit mmio pref: [0xc0000000-0xc7ffffff]
[ 0.014605] pci 0001:01:08.0: reg 14 io port: [0x1000-0x10ff]
[ 0.014632] pci 0001:01:08.0: reg 18 32bit mmio: [0xc8000000-0xc800ffff]
[ 0.014717] pci 0001:01:08.0: reg 30 32bit mmio pref: [0xc8020000-0xc803ffff]
[ 0.014858] pci 0001:01:08.1: reg 10 32bit mmio pref: [0xd0000000-0xd7ffffff]
[ 0.014885] pci 0001:01:08.1: reg 14 32bit mmio: [0xc8010000-0xc801ffff]
[ 0.015639] PCI 0000:00 Cannot reserve Legacy IO [0x00-0xfff]
[ 0.015664] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.015671] pci_bus 0000:00: resource 1 mem: [0x80000000-0xbfffffff]
[ 0.015679] pci_bus 0001:01: resource 0 io: [0xffff0000-0xffffffff]
[ 0.015687] pci_bus 0001:01: resource 1 mem: [0xc0000000-0xdfffffff]
[ 0.016790] bio: create slab <bio-0> at 0
[ 0.017200] vgaarb: device added: PCI:0001:01:08.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.017229] vgaarb: loaded
[ 0.017652] Switching to clocksource timebase
[ 0.022011] NET: Registered protocol family 2
[ 0.022312] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.023040] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.023452] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.023674] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.023696] TCP reno registered
[ 0.023961] NET: Registered protocol family 1
[ 0.024166] pci 0000:00:0c.1: Fixing VIA IDE, force legacy mode on
[ 0.024480] Unpacking initramfs...
[ 0.648831] Freeing initrd memory: 9513k freed
[ 0.650240] Thermal assist unit not available
[ 0.651330] audit: initializing netlink socket (disabled)
[ 0.651416] type=2000 audit(1308578508.648:1): initialized
[ 0.662514] VFS: Disk quotas dquot_6.5.2
[ 0.662736] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.662869] msgmni has been set to 1001
[ 0.663621] alg: No test for stdrng (krng)
[ 0.663751] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.663776] io scheduler noop registered
[ 0.663787] io scheduler anticipatory registered
[ 0.663800] io scheduler deadline registered
[ 0.663918] io scheduler cfq registered (default)
[ 0.863025] radeonfb: Found Intel x86 BIOS ROM Image
[ 0.863054] radeonfb: No ATY,RefCLK property !
[ 0.863090] radeonfb: Retrieved PLL infos from BIOS
[ 0.863105] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz, System=200.00 MHz
[ 0.863125] radeonfb: PLL min 20000 max 40000
[ 1.213690] radeonfb: Monitor 1 type DFP found
[ 1.213706] radeonfb: EDID probed
[ 1.213716] radeonfb: Monitor 2 type CRT found
[ 1.213727] radeonfb: EDID probed
[ 1.257687] Console: switching to colour frame buffer device 175x65
[ 1.287185] radeonfb (0001:01:08.0): ATI Radeon 5960 "Y`"
[ 1.291536] Generic non-volatile memory driver v1.1
[ 1.291812] Linux agpgart interface v0.103
[ 1.292019] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.292830] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 0) is a 16550A
[ 1.293302] pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
[ 1.293591] Serial: MPC52xx PSC UART driver
[ 1.294037] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.294402] Warning: no ADB interface detected
[ 1.294567] Uniform Multi-Platform E-IDE driver
[ 1.294843] ide-gd driver 1.18
[ 1.295198] mice: PS/2 mouse device common for all mice
[ 1.295517] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[ 1.296745] TCP cubic registered
[ 1.297266] NET: Registered protocol family 10
[ 1.299347] Mobile IPv6
[ 1.299478] NET: Registered protocol family 17
[ 1.300046] PM: Resume from disk failed.
[ 1.300099] registered taskstats version 1
[ 1.301438] rtc-generic rtc-generic: setting system clock to 2011-06-20 14:01:49 UTC (1308578509)
[ 1.301791] Initalizing network drop monitor service
[ 1.302066] Freeing unused kernel memory: 232k init
[ 1.382589] udev[40]: starting version 164
[ 1.607292] via82cxxx 0000:00:0c.1: VIA vt8231 (rev 10) IDE UDMA100
[ 1.607610] via82cxxx 0000:00:0c.1: IDE controller (0x1106:0x0571 rev 0x06)
[ 1.608083] via82cxxx 0000:00:0c.1: not 100% native mode: will probe irqs later
[ 1.608377] ide0: BM-DMA at 0x1020-0x1027
[ 1.608565] ide1: BM-DMA at 0x1028-0x102f
[ 1.608743] Probing IDE interface ide0...
[ 1.746175] usbcore: registered new interface driver usbfs
[ 1.746964] usbcore: registered new interface driver hub
[ 1.747665] usbcore: registered new device driver usb
[ 1.766275] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 1.813454] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.814342] mv643xx_eth smi: probed
[ 1.827721] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.847309] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.937920] hda: WDC WD3200BEVE-00A0HT0, ATA DISK drive
[ 2.207312] net eth0: port 1 with MAC address 00:2b:2f:de:ad:01
[ 2.216821] net eth0: configured with sram
[ 2.617861] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 2.618029] hda: UDMA/100 mode selected
[ 2.627552] Probing IDE interface ide1...
[ 3.025902] hdc: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive
[ 3.705979] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 3.706288] hdc: UDMA/33 mode selected
[ 3.715823] ide0 at 0x1000-0x1007,0x100e on irq 14
[ 3.725118] ide1 at 0x1010-0x1017,0x101e on irq 15
[ 3.734430] hda: max request size: 512KiB
[ 3.790905] hda: 625142448 sectors (320072 MB) w/8192KiB Cache, CHS=38913/255/63
[ 3.800732] hda: cache flushes supported
[ 3.810166] hda: RDSK (512) hda1 (LNX^@)(res 2 spb 1) hda2 (RFS^@)(res 2 spb 1) hda3 (FAT^@)(res 2 spb 1) hda4 (RFS^@)(res 2 spb 1) hda5 (SWP^@)(res 2 spb 1)
[ 3.831620] via-rhine 0000:00:0d.0: enabling device (0000 -> 0003)
[ 3.853427] eth1: VIA Rhine II at 0x80002900, 00:0b:2f:74:9c:c1, IRQ 9.
[ 3.864497] eth1: MII PHY found at address 16, status 0x784d advertising 01e1 Link 0020.
[ 3.874924] ehci_hcd 0000:00:06.2: enabling device (0000 -> 0002)
[ 3.889205] ehci_hcd 0000:00:06.2: EHCI Host Controller
[ 3.899711] ehci_hcd 0000:00:06.2: new USB bus registered, assigned bus number 1
[ 3.933754] ehci_hcd 0000:00:06.2: irq 9, io mem 0x80002800
[ 3.953704] ehci_hcd 0000:00:06.2: USB 2.0 started, EHCI 1.00
[ 3.964472] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.974831] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.985220] usb usb1: Product: EHCI Host Controller
[ 3.995529] usb usb1: Manufacturer: Linux 2.6.32-5-powerpc ehci_hcd
[ 4.005849] usb usb1: SerialNumber: 0000:00:06.2
[ 4.017323] usb usb1: configuration #1 chosen from 1 choice
[ 4.028021] hub 1-0:1.0: USB hub found
[ 4.038340] hub 1-0:1.0: 3 ports detected
[ 4.048758] firewire_ohci 0000:00:01.0: enabling device (0000 -> 0003)
[ 4.070947] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.149775] firewire_ohci: Added fw-ohci device 0000:00:01.0, OHCI version 1.0
[ 4.178143] ohci_hcd 0000:00:06.0: OHCI Host Controller
[ 4.190922] ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2
[ 4.201458] ohci_hcd 0000:00:06.0: irq 9, io mem 0x80000000
[ 4.295914] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.306306] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.316555] usb usb2: Product: OHCI Host Controller
[ 4.326694] usb usb2: Manufacturer: Linux 2.6.32-5-powerpc ohci_hcd
[ 4.336907] usb usb2: SerialNumber: 0000:00:06.0
[ 4.348209] usb usb2: configuration #1 chosen from 1 choice
[ 4.358855] hub 2-0:1.0: USB hub found
[ 4.369452] hub 2-0:1.0: 2 ports detected
[ 4.381952] uhci_hcd 0000:00:0c.2: enabling device (0000 -> 0001)
[ 4.455611] uhci_hcd 0000:00:0c.2: UHCI Host Controller
[ 4.465992] uhci_hcd 0000:00:0c.2: new USB bus registered, assigned bus number 3
[ 4.476550] uhci_hcd 0000:00:0c.2: irq 9, io base 0x00001040
[ 4.486888] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.496975] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.507034] usb usb3: Product: UHCI Host Controller
[ 4.517052] usb usb3: Manufacturer: Linux 2.6.32-5-powerpc uhci_hcd
[ 4.527050] usb usb3: SerialNumber: 0000:00:0c.2
[ 4.542679] SCSI subsystem initialized
[ 4.624888] usb usb3: configuration #1 chosen from 1 choice
[ 4.635785] hub 3-0:1.0: USB hub found
[ 4.646126] hub 3-0:1.0: 2 ports detected
[ 4.656529] firewire_core: created device fw0: GUID 0011060000004b2f, S400
[ 4.668838] ohci_hcd 0000:00:06.1: OHCI Host Controller
[ 4.679906] ohci_hcd 0000:00:06.1: new USB bus registered, assigned bus number 4
[ 4.690264] ohci_hcd 0000:00:06.1: irq 9, io mem 0x80001000
[ 4.701650] libata version 3.00 loaded.
[ 4.783983] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.794445] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.804647] usb usb4: Product: OHCI Host Controller
[ 4.814804] usb usb4: Manufacturer: Linux 2.6.32-5-powerpc ohci_hcd
[ 4.825043] usb usb4: SerialNumber: 0000:00:06.1
[ 4.836559] usb usb4: configuration #1 chosen from 1 choice
[ 4.847150] hub 4-0:1.0: USB hub found
[ 4.857383] hub 4-0:1.0: 1 port detected
[ 4.867842] uhci_hcd 0000:00:0c.3: enabling device (0000 -> 0001)
[ 4.893849] uhci_hcd 0000:00:0c.3: UHCI Host Controller
[ 4.906688] uhci_hcd 0000:00:0c.3: new USB bus registered, assigned bus number 5
[ 4.917140] uhci_hcd 0000:00:0c.3: irq 9, io base 0x00001060
[ 4.927151] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.936766] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.946293] usb usb5: Product: UHCI Host Controller
[ 4.955689] usb usb5: Manufacturer: Linux 2.6.32-5-powerpc uhci_hcd
[ 4.965040] usb usb5: SerialNumber: 0000:00:0c.3
[ 4.992223] usb usb5: configuration #1 chosen from 1 choice
[ 5.002305] hub 5-0:1.0: USB hub found
[ 5.011773] hub 5-0:1.0: 2 ports detected
[ 5.030016] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 5.121088] ide-cd driver 5.00
[ 5.132570] ide-cd: hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[ 5.142324] Uniform CD-ROM driver Revision: 3.20
[ 5.235102] usb 3-2: not running at top speed; connect to a high speed hub
[ 5.294054] usb 3-2: New USB device found, idVendor=03f0, idProduct=3417
[ 5.304040] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.313734] usb 3-2: Product: HP LaserJet 3055
[ 5.323384] usb 3-2: Manufacturer: Hewlett-Packard
[ 5.332943] usb 3-2: SerialNumber: 00CNCK544241
[ 5.344549] usb 3-2: configuration #1 chosen from 1 choice
[ 6.067184] REISERFS (device hda2): found reiserfs format "3.6" with standard journal
[ 6.077253] REISERFS (device hda2): using ordered data mode
[ 6.130205] REISERFS (device hda2): journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 6.145610] REISERFS (device hda2): checking transaction log (hda2)
[ 6.193351] REISERFS (device hda2): Using r5 hash to sort names
[ 9.384030] udev[185]: starting version 164
[ 11.569619] vt596_smbus 0000:00:0c.4: Enabling SMBus device
[ 11.869869] parport_pc: VIA 686A/8231 detected
[ 11.869886] parport_pc: probing current configuration
[ 11.869950] parport_pc: Current parallel port base: 0x3BC
[ 11.870029] parport0: PC-style at 0x3bc, irq 7 [PCSPP]
[ 11.909677] usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x3417
[ 11.939656] usbcore: registered new interface driver usblp
[ 11.985992] parport_pc: VIA parallel port: io=0x3BC, irq=7
[ 12.107658] vt8231 0000:00:0c.4: enabling sensors
[ 12.526516] VIA 82xx Modem 0000:00:0c.6: enabling device (0000 -> 0001)
[ 13.802022] VIA 82xx Modem: probe of 0000:00:0c.6 failed with error -13
[ 13.823873] VIA 82xx Audio 0000:00:0c.5: enabling device (0000 -> 0001)
[ 17.007617] Adding 2096472k swap on /dev/hda5. Priority:-1 extents:1 across:2096472k
[ 19.041921] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 19.041950] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 19.339110] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 19.567600] oprofile: using ppc/7450 performance monitoring.
[ 19.639575] usbcore: registered new interface driver usbserial
[ 19.658378] USB Serial support registered for generic
[ 19.676459] usbcore: registered new interface driver usbserial_generic
[ 19.694001] usbserial: USB Serial Driver core
[ 19.755874] USB Serial support registered for Handspring Visor / Palm OS
[ 19.773831] USB Serial support registered for Sony Clie 3.5
[ 19.791337] USB Serial support registered for Sony Clie 5.0
[ 19.810412] usbcore: registered new interface driver visor
[ 19.826607] visor: USB HandSpring Visor / Palm OS driver
[ 19.887070] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[ 19.937594] i2c /dev entries driver
[ 20.131428] Initializing USB Mass Storage driver...
[ 20.147759] usbcore: registered new interface driver usb-storage
[ 20.164073] USB Mass Storage support registered.
[ 20.806330] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2
[ 21.073904] REISERFS (device hda4): found reiserfs format "3.6" with standard journal
[ 21.087889] REISERFS (device hda4): using ordered data mode
[ 21.124222] REISERFS (device hda4): journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 21.142991] REISERFS (device hda4): checking transaction log (hda4)
[ 21.217484] REISERFS (device hda4): Using r5 hash to sort names
[ 25.631761] fuse init (API version 7.13)
[ 31.116656] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 32.582057] Bluetooth: Core ver 2.15
[ 32.600357] NET: Registered protocol family 31
[ 32.611938] Bluetooth: HCI device and connection manager initialized
[ 32.622946] Bluetooth: HCI socket layer initialized
[ 32.730738] Bluetooth: L2CAP ver 2.14
[ 32.741775] Bluetooth: L2CAP socket layer initialized
[ 32.895617] Bluetooth: RFCOMM TTY layer initialized
[ 32.918029] Bluetooth: RFCOMM socket layer initialized
[ 32.928962] Bluetooth: RFCOMM ver 1.11
[ 32.985882] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 32.996759] Bluetooth: BNEP filters: protocol multicast
[ 33.100661] Bridge firewalling registered
[ 33.302497] Bluetooth: SCO (Voice Link) ver 0.6
[ 33.313325] Bluetooth: SCO socket layer initialized
[ 33.621716] eth1: no IPv6 routers present
[ 0.000000] Using CHRP machine description
[ 0.000000] Total memory = 512MB; using 1024kB for hash table (at cff00000)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-powerpc (Debian 2.6.32-35) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 Tue Jun 14 09:33:14 UTC 2011
[ 0.000000] Found initrd at 0xc0643000:0xc0fad8b8
[ 0.000000] Found legacy serial port 0 for /pci@80000000/isa@C/serial@i2F8
[ 0.000000] port=2f8, taddr=fe0002f8, irq=0, clk=1843200, speed=0
[ 0.000000] bootconsole [udbg0] enabled
[ 0.000000] chrp type = 6 [Genesi Pegasos]
[ 0.000000] Pegasos l2cr : L2 cache was not active, activating
[ 0.000000] PCI bus 0 controlled by /pci@80000000 at 80000000
[ 0.000000] PCI host bridge /pci@80000000 (primary) ranges:
[ 0.000000] IO 0x00000000fe000000..0x00000000fe00ffff -> 0x0000000000000000
[ 0.000000] MEM 0x0000000080000000..0x00000000bfffffff -> 0x0000000080000000
[ 0.000000] PCI bus 0 controlled by /pci@C0000000 at c0000000
[ 0.000000] PCI host bridge /pci@C0000000 ranges:
[ 0.000000] IO 0x00000000f8000000..0x00000000f800ffff -> 0x0000000000000000
[ 0.000000] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.000000] Top of RAM: 0x20000000, Total RAM: 0x20000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00020000
[ 0.000000] Normal 0x00020000 -> 0x00020000
[ 0.000000] HighMem 0x00020000 -> 0x00020000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c0505328, node_mem_map c0fae000
[ 0.000000] DMA zone: 1024 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 130048 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: video=radeonfb:1400x1050-8@60 panic=300 root=UUID=39c3b58f-8331-4c14-828b-77eb1c2132df
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] High memory: 0k
[ 0.000000] Memory: 502784k/524288k available (4928k kernel code, 21052k reserved, 280k data, 478k bss, 232k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffef000..0xfffff000 : fixmap
[ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs
[ 0.000000] * 0xff7e0000..0xff800000 : early ioremap
[ 0.000000] * 0xe1000000..0xff7e0000 : vmalloc & ioremap
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512
[ 0.000000] i8259 legacy interrupt controller initialized
[ 0.000000] time_init: decrementer frequency = 33.333333 MHz
[ 0.000000] time_init: processor frequency = 999.999990 MHz
[ 0.000000] clocksource: timebase mult[7800001] shift[22] registered
[ 0.000000] clockevent: decrementer mult[8888887] shift[32] cpu[0]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000382] Security Framework initialized
[ 0.000427] SELinux: Disabled at boot.
[ 0.000453] Mount-cache hash table entries: 512
[ 0.001873] device-tree: Duplicate name in /pci@80000000/usb@C,2/device@1, renamed to "printer@0#1"
[ 0.002485] Initializing cgroup subsys ns
[ 0.002503] Initializing cgroup subsys cpuacct
[ 0.002516] Initializing cgroup subsys devices
[ 0.002528] Initializing cgroup subsys freezer
[ 0.002539] Initializing cgroup subsys net_cls
[ 0.003686] devtmpfs: initialized
[ 0.004853] regulator: core version 0.5
[ 0.005073] NET: Registered protocol family 16
[ 0.008305] MPC7450 family performance monitor hardware support registered
[ 0.008456] PCI: Probing PCI hardware
[ 0.008914] pci 0000:00:01.0: reg 10 32bit mmio: [0x80002000-0x800027ff]
[ 0.008941] pci 0000:00:01.0: reg 14 io port: [0x1080-0x10ff]
[ 0.009116] pci 0000:00:01.0: supports D2
[ 0.009123] pci 0000:00:01.0: PME# supported from D2 D3hot D3cold
[ 0.009146] pci 0000:00:01.0: PME# disabled
[ 0.009313] pci 0000:00:06.0: reg 10 32bit mmio: [0x80000000-0x80000fff]
[ 0.009504] pci 0000:00:06.0: supports D1 D2
[ 0.009509] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot
[ 0.009530] pci 0000:00:06.0: PME# disabled
[ 0.009673] pci 0000:00:06.1: reg 10 32bit mmio: [0x80001000-0x80001fff]
[ 0.009863] pci 0000:00:06.1: supports D1 D2
[ 0.009869] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot
[ 0.009889] pci 0000:00:06.1: PME# disabled
[ 0.010033] pci 0000:00:06.2: reg 10 32bit mmio: [0x80002800-0x800028ff]
[ 0.010223] pci 0000:00:06.2: supports D1 D2
[ 0.010229] pci 0000:00:06.2: PME# supported from D0 D1 D2 D3hot
[ 0.010249] pci 0000:00:06.2: PME# disabled
[ 0.010763] pci 0000:00:0c.1: reg 10 io port: [0x1000-0x1007]
[ 0.010789] pci 0000:00:0c.1: reg 14 io port: [0x100c-0x100f]
[ 0.010815] pci 0000:00:0c.1: reg 18 io port: [0x1010-0x1017]
[ 0.010840] pci 0000:00:0c.1: reg 1c io port: [0x101c-0x101f]
[ 0.010866] pci 0000:00:0c.1: reg 20 io port: [0x1020-0x102f]
[ 0.011208] pci 0000:00:0c.2: reg 20 io port: [0x1040-0x105f]
[ 0.011533] pci 0000:00:0c.3: reg 20 io port: [0x1060-0x107f]
[ 0.012100] pci 0000:00:0c.5: reg 10 io port: [0x1100-0x11ff]
[ 0.012126] pci 0000:00:0c.5: reg 14 io port: [0x1030-0x1033]
[ 0.012166] pci 0000:00:0c.5: reg 18 io port: [0x1034-0x1037]
[ 0.012458] pci 0000:00:0c.6: reg 10 io port: [0x1200-0x12ff]
[ 0.012791] pci 0000:00:0d.0: reg 10 io port: [0x1300-0x13ff]
[ 0.012818] pci 0000:00:0d.0: reg 14 32bit mmio: [0x80002900-0x800029ff]
[ 0.012992] pci 0000:00:0d.0: PME# supported from D0 D3hot D3cold
[ 0.013028] pci 0000:00:0d.0: PME# disabled
[ 0.014630] pci 0001:01:08.0: reg 10 32bit mmio pref: [0xc0000000-0xc7ffffff]
[ 0.014658] pci 0001:01:08.0: reg 14 io port: [0x1000-0x10ff]
[ 0.014685] pci 0001:01:08.0: reg 18 32bit mmio: [0xc8000000-0xc800ffff]
[ 0.014770] pci 0001:01:08.0: reg 30 32bit mmio pref: [0xc8020000-0xc803ffff]
[ 0.014912] pci 0001:01:08.1: reg 10 32bit mmio pref: [0xd0000000-0xd7ffffff]
[ 0.014940] pci 0001:01:08.1: reg 14 32bit mmio: [0xc8010000-0xc801ffff]
[ 0.015688] PCI 0000:00 Cannot reserve Legacy IO [0x00-0xfff]
[ 0.015714] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.015721] pci_bus 0000:00: resource 1 mem: [0x80000000-0xbfffffff]
[ 0.015729] pci_bus 0001:01: resource 0 io: [0xffff0000-0xffffffff]
[ 0.015737] pci_bus 0001:01: resource 1 mem: [0xc0000000-0xdfffffff]
[ 0.016841] bio: create slab <bio-0> at 0
[ 0.017235] vgaarb: device added: PCI:0001:01:08.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.017261] vgaarb: loaded
[ 0.017686] Switching to clocksource timebase
[ 0.022071] NET: Registered protocol family 2
[ 0.022370] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.023098] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.023507] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.023725] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.023746] TCP reno registered
[ 0.024015] NET: Registered protocol family 1
[ 0.024216] pci 0000:00:0c.1: Fixing VIA IDE, force legacy mode on
[ 0.024537] Unpacking initramfs...
[ 0.653280] Freeing initrd memory: 9642k freed
[ 0.654687] Thermal assist unit not available
[ 0.655778] audit: initializing netlink socket (disabled)
[ 0.655864] type=2000 audit(1308577279.652:1): initialized
[ 0.666939] VFS: Disk quotas dquot_6.5.2
[ 0.667162] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.667295] msgmni has been set to 1001
[ 0.668053] alg: No test for stdrng (krng)
[ 0.668190] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.668215] io scheduler noop registered
[ 0.668227] io scheduler anticipatory registered
[ 0.668239] io scheduler deadline registered
[ 0.668353] io scheduler cfq registered (default)
[ 0.867472] radeonfb: Found Intel x86 BIOS ROM Image
[ 0.867504] radeonfb: No ATY,RefCLK property !
[ 0.867541] radeonfb: Retrieved PLL infos from BIOS
[ 0.867557] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz, System=200.00 MHz
[ 0.867577] radeonfb: PLL min 20000 max 40000
[ 1.217727] radeonfb: Monitor 1 type DFP found
[ 1.217743] radeonfb: EDID probed
[ 1.217753] radeonfb: Monitor 2 type CRT found
[ 1.217764] radeonfb: EDID probed
[ 1.261865] Console: switching to colour frame buffer device 175x65
[ 1.291520] radeonfb (0001:01:08.0): ATI Radeon 5960 "Y`"
[ 1.295846] Generic non-volatile memory driver v1.1
[ 1.296125] Linux agpgart interface v0.103
[ 1.296341] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.297150] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 0) is a 16550A
[ 1.297633] pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
[ 1.297967] Serial: MPC52xx PSC UART driver
[ 1.298366] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.298731] Warning: no ADB interface detected
[ 1.298896] Uniform Multi-Platform E-IDE driver
[ 1.299173] ide-gd driver 1.18
[ 1.299548] mice: PS/2 mouse device common for all mice
[ 1.299878] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[ 1.301109] TCP cubic registered
[ 1.301649] NET: Registered protocol family 10
[ 1.303731] Mobile IPv6
[ 1.303854] NET: Registered protocol family 17
[ 1.304399] PM: Resume from disk failed.
[ 1.304463] registered taskstats version 1
[ 1.305838] rtc-generic rtc-generic: setting system clock to 2011-06-20 13:41:20 UTC (1308577280)
[ 1.306161] Initalizing network drop monitor service
[ 1.306432] Freeing unused kernel memory: 232k init
[ 1.386770] udev[40]: starting version 164
[ 1.610063] via82cxxx 0000:00:0c.1: VIA vt8231 (rev 10) IDE UDMA100
[ 1.610375] via82cxxx 0000:00:0c.1: IDE controller (0x1106:0x0571 rev 0x06)
[ 1.610810] via82cxxx 0000:00:0c.1: not 100% native mode: will probe irqs later
[ 1.611103] ide0: BM-DMA at 0x1020-0x1027
[ 1.611292] ide1: BM-DMA at 0x1028-0x102f
[ 1.611468] Probing IDE interface ide0...
[ 1.744686] usbcore: registered new interface driver usbfs
[ 1.745499] usbcore: registered new interface driver hub
[ 1.746253] usbcore: registered new device driver usb
[ 1.754566] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 1.800207] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.823386] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.823933] mv643xx_eth smi: probed
[ 1.921965] hda: WDC WD3200BEVE-00A0HT0, ATA DISK drive
[ 2.219350] net eth0: port 1 with MAC address 00:2b:2f:de:ad:01
[ 2.228835] net eth0: configured with sram
[ 2.601909] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 2.602082] hda: UDMA/100 mode selected
[ 2.611669] Probing IDE interface ide1...
[ 3.009936] hdc: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive
[ 3.690015] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 3.690291] hdc: UDMA/33 mode selected
[ 3.699872] ide0 at 0x1000-0x1007,0x100e on irq 14
[ 3.709225] ide1 at 0x1010-0x1017,0x101e on irq 15
[ 3.718669] hda: max request size: 512KiB
[ 3.794438] hda: 625142448 sectors (320072 MB) w/8192KiB Cache, CHS=38913/255/63
[ 3.803801] hda: cache flushes supported
[ 3.813155] hda: RDSK (512) hda1 (LNX^@)(res 2 spb 1) hda2 (RFS^@)(res 2 spb 1) hda3 (FAT^@)(res 2 spb 1) hda4 (RFS^@)(res 2 spb 1) hda5 (SWP^@)(res 2 spb 1)
[ 3.835556] via-rhine 0000:00:0d.0: enabling device (0000 -> 0003)
[ 3.856778] eth1: VIA Rhine II at 0x80002900, 00:0b:2f:74:9c:c1, IRQ 9.
[ 3.867800] eth1: MII PHY found at address 16, status 0x784d advertising 01e1 Link 0020.
[ 3.878172] ehci_hcd 0000:00:06.2: enabling device (0000 -> 0002)
[ 3.893176] ehci_hcd 0000:00:06.2: EHCI Host Controller
[ 3.903785] ehci_hcd 0000:00:06.2: new USB bus registered, assigned bus number 1
[ 3.937798] ehci_hcd 0000:00:06.2: irq 9, io mem 0x80002800
[ 3.957728] ehci_hcd 0000:00:06.2: USB 2.0 started, EHCI 1.00
[ 3.968040] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 3.978330] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.988658] usb usb1: Product: EHCI Host Controller
[ 3.999008] usb usb1: Manufacturer: Linux 2.6.32-5-powerpc ehci_hcd
[ 4.009365] usb usb1: SerialNumber: 0000:00:06.2
[ 4.020863] usb usb1: configuration #1 chosen from 1 choice
[ 4.031586] hub 1-0:1.0: USB hub found
[ 4.042134] hub 1-0:1.0: 3 ports detected
[ 4.052929] firewire_ohci 0000:00:01.0: enabling device (0000 -> 0003)
[ 4.074893] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.167471] firewire_ohci: Added fw-ohci device 0000:00:01.0, OHCI version 1.0
[ 4.190211] uhci_hcd 0000:00:0c.2: enabling device (0000 -> 0001)
[ 4.205887] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.281261] uhci_hcd 0000:00:0c.2: UHCI Host Controller
[ 4.293867] uhci_hcd 0000:00:0c.2: new USB bus registered, assigned bus number 2
[ 4.304694] uhci_hcd 0000:00:0c.2: irq 9, io base 0x00001040
[ 4.315195] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.325500] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.335710] usb usb2: Product: UHCI Host Controller
[ 4.345900] usb usb2: Manufacturer: Linux 2.6.32-5-powerpc uhci_hcd
[ 4.356165] usb usb2: SerialNumber: 0000:00:0c.2
[ 4.373062] SCSI subsystem initialized
[ 4.455509] usb usb2: configuration #1 chosen from 1 choice
[ 4.466436] hub 2-0:1.0: USB hub found
[ 4.476882] hub 2-0:1.0: 2 ports detected
[ 4.487540] ohci_hcd 0000:00:06.0: OHCI Host Controller
[ 4.497700] ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 3
[ 4.508439] ohci_hcd 0000:00:06.0: irq 9, io mem 0x80000000
[ 4.520127] libata version 3.00 loaded.
[ 4.603792] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.614156] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.624313] usb usb3: Product: OHCI Host Controller
[ 4.634314] usb usb3: Manufacturer: Linux 2.6.32-5-powerpc ohci_hcd
[ 4.644462] usb usb3: SerialNumber: 0000:00:06.0
[ 4.656048] usb usb3: configuration #1 chosen from 1 choice
[ 4.666673] firewire_core: created device fw0: GUID 0011060000004b2f, S400
[ 4.678860] hub 3-0:1.0: USB hub found
[ 4.689384] hub 3-0:1.0: 2 ports detected
[ 4.699889] uhci_hcd 0000:00:0c.3: enabling device (0000 -> 0001)
[ 4.711040] uhci_hcd 0000:00:0c.3: UHCI Host Controller
[ 4.721320] uhci_hcd 0000:00:0c.3: new USB bus registered, assigned bus number 4
[ 4.731607] uhci_hcd 0000:00:0c.3: irq 9, io base 0x00001060
[ 4.741890] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.752134] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.762406] usb usb4: Product: UHCI Host Controller
[ 4.772608] usb usb4: Manufacturer: Linux 2.6.32-5-powerpc uhci_hcd
[ 4.782856] usb usb4: SerialNumber: 0000:00:0c.3
[ 4.794473] usb usb4: configuration #1 chosen from 1 choice
[ 4.805249] hub 4-0:1.0: USB hub found
[ 4.815813] hub 4-0:1.0: 2 ports detected
[ 4.826963] ohci_hcd 0000:00:06.1: OHCI Host Controller
[ 4.846224] usb 2-2: new full speed USB device using uhci_hcd and address 2
[ 4.891218] ohci_hcd 0000:00:06.1: new USB bus registered, assigned bus number 5
[ 4.940520] ohci_hcd 0000:00:06.1: irq 9, io mem 0x80001000
[ 4.957055] ide-cd driver 5.00
[ 4.967920] ide-cd: hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[ 4.977704] Uniform CD-ROM driver Revision: 3.20
[ 5.040860] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.051026] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.060770] usb usb5: Product: OHCI Host Controller
[ 5.070464] usb usb5: Manufacturer: Linux 2.6.32-5-powerpc ohci_hcd
[ 5.080155] usb usb5: SerialNumber: 0000:00:06.1
[ 5.106938] usb usb5: configuration #1 chosen from 1 choice
[ 5.117085] usb 2-2: not running at top speed; connect to a high speed hub
[ 5.160777] hub 5-0:1.0: USB hub found
[ 5.171713] hub 5-0:1.0: 1 port detected
[ 5.205365] usb 2-2: New USB device found, idVendor=03f0, idProduct=3417
[ 5.215512] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.225432] usb 2-2: Product: HP LaserJet 3055
[ 5.235179] usb 2-2: Manufacturer: Hewlett-Packard
[ 5.244846] usb 2-2: SerialNumber: 00CNCK544241
[ 5.273099] usb 2-2: configuration #1 chosen from 1 choice
[ 5.925613] REISERFS (device hda2): found reiserfs format "3.6" with standard journal
[ 5.935841] REISERFS (device hda2): using ordered data mode
[ 5.989525] REISERFS (device hda2): journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 6.004997] REISERFS (device hda2): checking transaction log (hda2)
[ 6.052669] REISERFS (device hda2): Using r5 hash to sort names
[ 9.177124] udev[185]: starting version 164
[ 11.492338] vt596_smbus 0000:00:0c.4: Enabling SMBus device
[ 11.633167] parport_pc: VIA 686A/8231 detected
[ 11.633187] parport_pc: probing current configuration
[ 11.633246] parport_pc: Current parallel port base: 0x3BC
[ 11.633316] parport0: PC-style at 0x3bc, irq 7 [PCSPP]
[ 11.740108] parport_pc: VIA parallel port: io=0x3BC, irq=7
[ 11.763839] vt8231 0000:00:0c.4: enabling sensors
[ 11.850727] usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x3417
[ 11.935962] usbcore: registered new interface driver usblp
[ 12.323786] VIA 82xx Modem 0000:00:0c.6: enabling device (0000 -> 0001)
[ 13.602072] VIA 82xx Modem: probe of 0000:00:0c.6 failed with error -13
[ 13.623765] VIA 82xx Audio 0000:00:0c.5: enabling device (0000 -> 0001)
[ 16.645128] Adding 2096472k swap on /dev/hda5. Priority:-1 extents:1 across:2096472k
[ 18.705961] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 18.706012] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 18.951553] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 19.365330] oprofile: using ppc/7450 performance monitoring.
[ 19.550348] usbcore: registered new interface driver usbserial
[ 19.569546] USB Serial support registered for generic
[ 19.587973] usbcore: registered new interface driver usbserial_generic
[ 19.605536] usbserial: USB Serial Driver core
[ 19.690194] USB Serial support registered for Handspring Visor / Palm OS
[ 19.708405] USB Serial support registered for Sony Clie 3.5
[ 19.726229] USB Serial support registered for Sony Clie 5.0
[ 19.743389] usbcore: registered new interface driver visor
[ 19.759399] visor: USB HandSpring Visor / Palm OS driver
[ 19.892418] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[ 20.037459] i2c /dev entries driver
[ 20.360915] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2
[ 20.495198] Initializing USB Mass Storage driver...
[ 20.511455] usbcore: registered new interface driver usb-storage
[ 20.527759] USB Mass Storage support registered.
[ 21.489246] REISERFS (device hda4): found reiserfs format "3.6" with standard journal
[ 21.503236] REISERFS (device hda4): using ordered data mode
[ 21.517370] REISERFS (device hda4): journal params: device hda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 21.536192] REISERFS (device hda4): checking transaction log (hda4)
[ 21.620459] REISERFS (device hda4): Using r5 hash to sort names
[ 24.915743] fuse init (API version 7.13)
[ 30.471792] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 32.120995] Bluetooth: Core ver 2.15
[ 32.132930] NET: Registered protocol family 31
[ 32.143628] Bluetooth: HCI device and connection manager initialized
[ 32.154186] Bluetooth: HCI socket layer initialized
[ 32.196091] Bluetooth: L2CAP ver 2.14
[ 32.206683] Bluetooth: L2CAP socket layer initialized
[ 32.445483] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 32.455873] Bluetooth: BNEP filters: protocol multicast
[ 32.565943] Bridge firewalling registered
[ 32.880518] Bluetooth: SCO (Voice Link) ver 0.6
[ 32.890681] Bluetooth: SCO socket layer initialized
[ 32.922736] Bluetooth: RFCOMM TTY layer initialized
[ 32.940125] Bluetooth: RFCOMM socket layer initialized
[ 32.950187] Bluetooth: RFCOMM ver 1.11
[ 34.337774] eth1: no IPv6 routers present
[ 0.000000] Using CHRP machine description
[ 0.000000] Total memory = 512MB; using 1024kB for hash table (at cff00000)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.33-2-powerpc (Debian 2.6.33-1~experimental.5) (maks@debian.org) (gcc version 4.3.4 (Debian 4.3.4-10) ) #1 Wed May 5 20:43:17 UTC 2010
[ 0.000000] Found initrd at 0xc0641000:0xc0fb20ce
[ 0.000000] Found legacy serial port 0 for /pci@80000000/isa@C/serial@i2F8
[ 0.000000] port=2f8, taddr=fe0002f8, irq=0, clk=1843200, speed=0
[ 0.000000] bootconsole [udbg0] enabled
[ 0.000000] chrp type = 6 [Genesi Pegasos]
[ 0.000000] Pegasos l2cr : L2 cache was not active, activating
[ 0.000000] PCI bus 0 controlled by /pci@80000000 at 80000000
[ 0.000000] PCI host bridge /pci@80000000 (primary) ranges:
[ 0.000000] IO 0x00000000fe000000..0x00000000fe00ffff -> 0x0000000000000000
[ 0.000000] MEM 0x0000000080000000..0x00000000bfffffff -> 0x0000000080000000
[ 0.000000] PCI bus 0 controlled by /pci@C0000000 at c0000000
[ 0.000000] PCI host bridge /pci@C0000000 ranges:
[ 0.000000] IO 0x00000000f8000000..0x00000000f800ffff -> 0x0000000000000000
[ 0.000000] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.000000] Top of RAM: 0x20000000, Total RAM: 0x20000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00020000
[ 0.000000] Normal 0x00020000 -> 0x00020000
[ 0.000000] HighMem 0x00020000 -> 0x00020000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c04f327c, node_mem_map c0fb3000
[ 0.000000] DMA zone: 1024 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 130048 pages, LIFO batch:31
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: video=radeonfb:1400x1050-8@60 panic=300 root=UUID=39c3b58f-8331-4c14-828b-77eb1c2132df
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] High memory: 0k
[ 0.000000] Memory: 502784k/524288k available (4892k kernel code, 21008k reserved, 244k data, 472k bss, 232k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffd0000..0xfffff000 : fixmap
[ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs
[ 0.000000] * 0xff7e0000..0xff800000 : early ioremap
[ 0.000000] * 0xe1000000..0xff7e0000 : vmalloc & ioremap
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:512 nr_irqs:512
[ 0.000000] i8259 legacy interrupt controller initialized
[ 0.000000] time_init: decrementer frequency = 33.333333 MHz
[ 0.000000] time_init: processor frequency = 999.999990 MHz
[ 0.000000] clocksource: timebase mult[7800001] shift[22] registered
[ 0.000000] clockevent: decrementer mult[8888887] shift[32] cpu[0]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000399] Security Framework initialized
[ 0.000443] SELinux: Disabled at boot.
[ 0.000468] Mount-cache hash table entries: 512
[ 0.001839] device-tree: Duplicate name in /pci@80000000/usb@C,2/device@1, renamed to "printer@0#1"
[ 0.002437] Initializing cgroup subsys ns
[ 0.002458] Initializing cgroup subsys cpuacct
[ 0.002470] Initializing cgroup subsys devices
[ 0.002480] Initializing cgroup subsys freezer
[ 0.002491] Initializing cgroup subsys net_cls
[ 0.003608] devtmpfs: initialized
[ 0.004403] regulator: core version 0.5
[ 0.004576] NET: Registered protocol family 16
[ 0.007795] MPC7450 family performance monitor hardware support registered
[ 0.007921] PCI: Probing PCI hardware
[ 0.008421] pci 0000:00:01.0: reg 10: [mem 0x80002000-0x800027ff]
[ 0.008449] pci 0000:00:01.0: reg 14: [io 0x1080-0x10ff]
[ 0.008625] pci 0000:00:01.0: supports D2
[ 0.008632] pci 0000:00:01.0: PME# supported from D2 D3hot D3cold
[ 0.008649] pci 0000:00:01.0: PME# disabled
[ 0.008792] pci 0000:00:06.0: reg 10: [mem 0x80000000-0x80000fff]
[ 0.008983] pci 0000:00:06.0: supports D1 D2
[ 0.008989] pci 0000:00:06.0: PME# supported from D0 D1 D2 D3hot
[ 0.009004] pci 0000:00:06.0: PME# disabled
[ 0.009125] pci 0000:00:06.1: reg 10: [mem 0x80001000-0x80001fff]
[ 0.009317] pci 0000:00:06.1: supports D1 D2
[ 0.009323] pci 0000:00:06.1: PME# supported from D0 D1 D2 D3hot
[ 0.009338] pci 0000:00:06.1: PME# disabled
[ 0.009458] pci 0000:00:06.2: reg 10: [mem 0x80002800-0x800028ff]
[ 0.009650] pci 0000:00:06.2: supports D1 D2
[ 0.009655] pci 0000:00:06.2: PME# supported from D0 D1 D2 D3hot
[ 0.009671] pci 0000:00:06.2: PME# disabled
[ 0.010151] pci 0000:00:0c.1: reg 10: [io 0x1000-0x1007]
[ 0.010178] pci 0000:00:0c.1: reg 14: [io 0x100c-0x100f]
[ 0.010204] pci 0000:00:0c.1: reg 18: [io 0x1010-0x1017]
[ 0.010230] pci 0000:00:0c.1: reg 1c: [io 0x101c-0x101f]
[ 0.010255] pci 0000:00:0c.1: reg 20: [io 0x1020-0x102f]
[ 0.010570] pci 0000:00:0c.2: reg 20: [io 0x1040-0x105f]
[ 0.010877] pci 0000:00:0c.3: reg 20: [io 0x1060-0x107f]
[ 0.011405] pci 0000:00:0c.5: reg 10: [io 0x1100-0x11ff]
[ 0.011431] pci 0000:00:0c.5: reg 14: [io 0x1030-0x1033]
[ 0.011457] pci 0000:00:0c.5: reg 18: [io 0x1034-0x1037]
[ 0.011728] pci 0000:00:0c.6: reg 10: [io 0x1200-0x12ff]
[ 0.012043] pci 0000:00:0d.0: reg 10: [io 0x1300-0x13ff]
[ 0.012069] pci 0000:00:0d.0: reg 14: [mem 0x80002900-0x800029ff]
[ 0.012258] pci 0000:00:0d.0: PME# supported from D0 D3hot D3cold
[ 0.012274] pci 0000:00:0d.0: PME# disabled
[ 0.013855] pci 0001:01:08.0: reg 10: [mem 0xc0000000-0xc7ffffff pref]
[ 0.013883] pci 0001:01:08.0: reg 14: [io 0x1000-0x10ff]
[ 0.013909] pci 0001:01:08.0: reg 18: [mem 0xc8000000-0xc800ffff]
[ 0.013995] pci 0001:01:08.0: reg 30: [mem 0xc8020000-0xc803ffff pref]
[ 0.014121] pci 0001:01:08.1: reg 10: [mem 0xd0000000-0xd7ffffff pref]
[ 0.014148] pci 0001:01:08.1: reg 14: [mem 0xc8010000-0xc801ffff]
[ 0.014939] PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff]
[ 0.014969] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.014976] pci_bus 0000:00: resource 1 [mem 0x80000000-0xbfffffff]
[ 0.014984] pci_bus 0001:01: resource 0 [io 0xffff0000-0xffffffff]
[ 0.014992] pci_bus 0001:01: resource 1 [mem 0xc0000000-0xdfffffff]
[ 0.016075] bio: create slab <bio-0> at 0
[ 0.016522] vgaarb: device added: PCI:0001:01:08.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.016540] vgaarb: loaded
[ 0.016935] Switching to clocksource timebase
[ 0.021464] NET: Registered protocol family 2
[ 0.021661] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.022201] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.022635] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.022852] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.022877] TCP reno registered
[ 0.022892] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.022925] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.023178] NET: Registered protocol family 1
[ 0.023404] pci 0000:00:0c.1: Fixing VIA IDE, force legacy mode on
[ 0.023536] PCI: CLS 128 bytes, default 32
[ 0.023777] Unpacking initramfs...
[ 0.616334] Freeing initrd memory: 9668k freed
[ 0.617837] RTAS daemon started
[ 0.617858] Thermal assist unit not available
[ 0.618934] audit: initializing netlink socket (disabled)
[ 0.619012] type=2000 audit(1308578320.616:1): initialized
[ 0.623374] VFS: Disk quotas dquot_6.5.2
[ 0.623594] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.623741] msgmni has been set to 1001
[ 0.624436] alg: No test for stdrng (krng)
[ 0.624569] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.624594] io scheduler noop registered
[ 0.624606] io scheduler deadline registered
[ 0.624797] io scheduler cfq registered (default)
[ 0.823979] radeonfb: Found Intel x86 BIOS ROM Image
[ 0.824011] radeonfb: No ATY,RefCLK property !
[ 0.824048] radeonfb: Retrieved PLL infos from BIOS
[ 0.824064] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz, System=200.00 MHz
[ 0.824084] radeonfb: PLL min 20000 max 40000
[ 1.172961] radeonfb: Monitor 1 type DFP found
[ 1.172976] radeonfb: EDID probed
[ 1.172987] radeonfb: Monitor 2 type CRT found
[ 1.172997] radeonfb: EDID probed
[ 1.217134] Console: switching to colour frame buffer device 175x65
[ 1.246807] radeonfb (0001:01:08.0): ATI Radeon 5960 "Y`"
[ 1.251012] Generic non-volatile memory driver v1.1
[ 1.251321] Linux agpgart interface v0.103
[ 1.251542] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.252316] serial8250.0: ttyS0 at I/O 0x2f8 (irq = 0) is a 16550A
[ 1.252754] pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)
[ 1.253101] Serial: MPC52xx PSC UART driver
[ 1.253538] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 1.253894] Warning: no ADB interface detected
[ 1.254060] Uniform Multi-Platform E-IDE driver
[ 1.254339] ide-gd driver 1.18
[ 1.254708] mice: PS/2 mouse device common for all mice
[ 1.255003] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[ 1.255966] TCP cubic registered
[ 1.256519] NET: Registered protocol family 10
[ 1.257664] lo: Disabled Privacy Extensions
[ 1.258344] Mobile IPv6
[ 1.258452] NET: Registered protocol family 17
[ 1.258966] PM: Resume from disk failed.
[ 1.258997] registered taskstats version 1
[ 1.260063] rtc-generic rtc-generic: setting system clock to 2011-06-20 13:58:41 UTC (1308578321)
[ 1.260386] Initalizing network drop monitor service
[ 1.260649] Freeing unused kernel memory: 232k init
[ 1.340535] udev[40]: starting version 164
[ 1.575831] via82cxxx 0000:00:0c.1: VIA vt8231 (rev 10) IDE UDMA100
[ 1.576111] via82cxxx 0000:00:0c.1: IDE controller (0x1106:0x0571 rev 0x06)
[ 1.576563] via82cxxx 0000:00:0c.1: not 100% native mode: will probe irqs later
[ 1.576857] ide0: BM-DMA at 0x1020-0x1027
[ 1.577112] ide1: BM-DMA at 0x1028-0x102f
[ 1.577294] Probing IDE interface ide0...
[ 1.628471] event-scan failed
[ 1.697903] usbcore: registered new interface driver usbfs
[ 1.698639] usbcore: registered new interface driver hub
[ 1.698995] usbcore: registered new device driver usb
[ 1.712519] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 1.720821] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.782335] MV-643xx 10/100/1000 ethernet driver version 1.4
[ 1.794351] mv643xx_eth smi: probed
[ 1.817001] event-scan failed
[ 1.828974] event-scan failed
[ 1.841135] event-scan failed
[ 1.857118] event-scan failed
[ 1.873015] event-scan failed
[ 1.885073] event-scan failed
[ 1.896973] event-scan failed
[ 1.908968] event-scan failed
[ 1.920978] event-scan failed
[ 1.928958] event-scan failed
[ 1.936960] event-scan failed
[ 1.945006] hda: WDC WD3200BEVE-00A0HT0, ATA DISK drive
[ 1.953069] event-scan failed
[ 1.964963] event-scan failed
[ 1.972972] event-scan failed
[ 1.980956] event-scan failed
[ 1.988966] event-scan failed
[ 1.996962] event-scan failed
[ 2.004962] event-scan failed
[ 2.012960] event-scan failed
[ 2.020957] event-scan failed
[ 2.028958] event-scan failed
[ 2.036955] event-scan failed
[ 2.044956] event-scan failed
[ 2.052956] event-scan failed
[ 2.060973] event-scan failed
[ 2.210258] net eth0: port 1 with MAC address 00:2b:2f:de:ad:01
[ 2.216718] net eth0: configured with sram
[ 2.621125] hda: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 2.621294] hda: UDMA/100 mode selected
[ 2.627799] Probing IDE interface ide1...
[ 2.816963] event-scan failed
[ 2.824962] event-scan failed
[ 2.832954] event-scan failed
[ 2.840961] event-scan failed
[ 2.848953] event-scan failed
[ 2.856961] event-scan failed
[ 2.864958] event-scan failed
[ 2.872955] event-scan failed
[ 2.880954] event-scan failed
[ 2.888953] event-scan failed
[ 2.896962] event-scan failed
[ 2.904953] event-scan failed
[ 2.912962] event-scan failed
[ 2.920952] event-scan failed
[ 2.928953] event-scan failed
[ 2.936955] event-scan failed
[ 2.940955] event-scan failed
[ 2.945088] event-scan failed
[ 2.948956] event-scan failed
[ 2.952955] event-scan failed
[ 2.956955] event-scan failed
[ 2.960955] event-scan failed
[ 2.964958] event-scan failed
[ 2.968960] event-scan failed
[ 2.972964] event-scan failed
[ 2.976954] event-scan failed
[ 2.980954] event-scan failed
[ 2.984955] event-scan failed
[ 2.988955] event-scan failed
[ 2.992954] event-scan failed
[ 2.996958] event-scan failed
[ 3.000956] event-scan failed
[ 3.004956] event-scan failed
[ 3.008955] event-scan failed
[ 3.012955] event-scan failed
[ 3.016957] event-scan failed
[ 3.020955] event-scan failed
[ 3.025170] hdc: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive
[ 3.027486] event-scan failed
[ 3.032954] event-scan failed
[ 3.036954] event-scan failed
[ 3.040956] event-scan failed
[ 3.044955] event-scan failed
[ 3.048958] event-scan failed
[ 3.052954] event-scan failed
[ 3.056953] event-scan failed
[ 3.060956] event-scan failed
[ 3.064957] event-scan failed
[ 3.697075] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 3.697306] hdc: UDMA/33 mode selected
[ 3.699730] ide0 at 0x1000-0x1007,0x100e on irq 14
[ 3.702821] ide1 at 0x1010-0x1017,0x101e on irq 15
[ 3.705520] hda: max request size: 512KiB
[ 3.770776] hda: 625142448 sectors (320072 MB) w/8192KiB Cache, CHS=38913/255/63
[ 3.773735] hda: cache flushes supported
[ 3.776737] hda: RDSK (512) hda1 (LNX^@)(res 2 spb 1) hda2 (RFS^@)(res 2 spb 1) hda3 (FAT^@)(res 2 spb 1) hda4 (RFS^@)(res 2 spb 1) hda5 (SWP^@)(res 2 spb 1)
[ 3.797626] via-rhine 0000:00:0d.0: enabling device (0000 -> 0003)
[ 3.815312] eth1: VIA Rhine II at 0x80002900, 00:0b:2f:74:9c:c1, IRQ 9.
[ 3.820152] eth1: MII PHY found at address 16, status 0x784d advertising 01e1 Link 0020.
[ 3.824149] event-scan failed
[ 3.829988] event-scan failed
[ 3.888187] event-scan failed
[ 3.892381] ehci_hcd 0000:00:06.2: enabling device (0000 -> 0002)
[ 3.898271] event-scan failed
[ 3.902634] ehci_hcd 0000:00:06.2: EHCI Host Controller
[ 3.906987] event-scan failed
[ 3.911459] ehci_hcd 0000:00:06.2: new USB bus registered, assigned bus number 1
[ 3.916174] event-scan failed
[ 3.921076] event-scan failed
[ 3.929237] event-scan failed
[ 3.937981] SCSI subsystem initialized
[ 3.944567] event-scan failed
[ 3.949741] ehci_hcd 0000:00:06.2: irq 9, io mem 0x80002800
[ 3.957121] event-scan failed
[ 3.970728] event-scan failed
[ 4.035748] ehci_hcd 0000:00:06.2: USB 2.0 started, EHCI 1.00
[ 4.042676] event-scan failed
[ 4.048430] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.054238] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.060141] usb usb1: Product: EHCI Host Controller
[ 4.066127] usb usb1: Manufacturer: Linux 2.6.33-2-powerpc ehci_hcd
[ 4.072294] usb usb1: SerialNumber: 0000:00:06.2
[ 4.078548] event-scan failed
[ 4.086056] hub 1-0:1.0: USB hub found
[ 4.093193] hub 1-0:1.0: 3 ports detected
[ 4.099999] firewire_ohci 0000:00:01.0: enabling device (0000 -> 0003)
[ 4.121321] libata version 3.00 loaded.
[ 4.128759] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.168230] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.193055] firewire_ohci: Added fw-ohci device 0000:00:01.0, OHCI version 1.0
[ 4.204793] ohci_hcd 0000:00:06.0: OHCI Host Controller
[ 4.215943] ohci_hcd 0000:00:06.0: new USB bus registered, assigned bus number 2
[ 4.223861] ohci_hcd 0000:00:06.0: irq 9, io mem 0x80000000
[ 4.315172] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.323110] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.331116] usb usb2: Product: OHCI Host Controller
[ 4.339208] usb usb2: Manufacturer: Linux 2.6.33-2-powerpc ohci_hcd
[ 4.347480] usb usb2: SerialNumber: 0000:00:06.0
[ 4.356834] hub 2-0:1.0: USB hub found
[ 4.365773] hub 2-0:1.0: 2 ports detected
[ 4.374324] uhci_hcd 0000:00:0c.2: enabling device (0000 -> 0001)
[ 4.382828] uhci_hcd 0000:00:0c.2: UHCI Host Controller
[ 4.391358] uhci_hcd 0000:00:0c.2: new USB bus registered, assigned bus number 3
[ 4.400119] uhci_hcd 0000:00:0c.2: irq 9, io base 0x00001040
[ 4.409061] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.418082] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.427206] usb usb3: Product: UHCI Host Controller
[ 4.436412] usb usb3: Manufacturer: Linux 2.6.33-2-powerpc uhci_hcd
[ 4.445794] usb usb3: SerialNumber: 0000:00:0c.2
[ 4.458261] hub 3-0:1.0: USB hub found
[ 4.472004] hub 3-0:1.0: 2 ports detected
[ 4.485752] ohci_hcd 0000:00:06.1: OHCI Host Controller
[ 4.533212] ohci_hcd 0000:00:06.1: new USB bus registered, assigned bus number 4
[ 4.567435] ohci_hcd 0000:00:06.1: irq 9, io mem 0x80001000
[ 4.588228] ide-cd driver 5.00
[ 4.598987] ide-cd: hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache
[ 4.608450] Uniform CD-ROM driver Revision: 3.20
[ 4.671720] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.681213] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.690204] usb usb4: Product: OHCI Host Controller
[ 4.698995] usb usb4: Manufacturer: Linux 2.6.33-2-powerpc ohci_hcd
[ 4.707954] usb usb4: SerialNumber: 0000:00:06.1
[ 4.717748] firewire_core: created device fw0: GUID 0011060000004b2f, S400
[ 4.778141] hub 4-0:1.0: USB hub found
[ 4.788373] hub 4-0:1.0: 1 port detected
[ 4.798324] uhci_hcd 0000:00:0c.3: enabling device (0000 -> 0001)
[ 4.817158] event-scan failed
[ 4.833542] uhci_hcd 0000:00:0c.3: UHCI Host Controller
[ 4.843666] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 4.855491] event-scan failed
[ 4.865152] uhci_hcd 0000:00:0c.3: new USB bus registered, assigned bus number 5
[ 4.882301] event-scan failed
[ 4.899772] uhci_hcd 0000:00:0c.3: irq 9, io base 0x00001060
[ 4.914126] event-scan failed
[ 4.924611] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.934652] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.944489] usb usb5: Product: UHCI Host Controller
[ 4.954249] usb usb5: Manufacturer: Linux 2.6.33-2-powerpc uhci_hcd
[ 4.964003] usb usb5: SerialNumber: 0000:00:0c.3
[ 4.974784] event-scan failed
[ 4.985022] event-scan failed
[ 4.996099] hub 5-0:1.0: USB hub found
[ 5.005744] event-scan failed
[ 5.015240] hub 5-0:1.0: 2 ports detected
[ 5.024789] event-scan failed
[ 5.053156] event-scan failed
[ 5.065066] event-scan failed
[ 5.074630] usb 3-2: not running at top speed; connect to a high speed hub
[ 5.118200] usb 3-2: New USB device found, idVendor=03f0, idProduct=3417
[ 5.127677] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.136962] usb 3-2: Product: HP LaserJet 3055
[ 5.146129] usb 3-2: Manufacturer: Hewlett-Packard
[ 5.155250] usb 3-2: SerialNumber: 00CNCK544241
[ 5.730483] REISERFS (device hda2): found reiserfs format "3.6" with standard journal
[ 5.740273] REISERFS (device hda2): using ordered data mode
[ 5.799438] REISERFS (device hda2): journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 5.814665] REISERFS (device hda2): checking transaction log (hda2)
[ 5.825137] event-scan failed
[ 5.836999] event-scan failed
[ 5.848977] event-scan failed
[ 5.860951] event-scan failed
[ 5.872955] event-scan failed
[ 5.884953] event-scan failed
[ 5.895869] REISERFS (device hda2): Using r5 hash to sort names
[ 5.905196] event-scan failed
[ 5.925011] event-scan failed
[ 5.935354] event-scan failed
[ 5.952989] event-scan failed
[ 5.963124] event-scan failed
[ 5.979564] event-scan failed
[ 5.997085] event-scan failed
[ 6.025582] event-scan failed
[ 6.039356] event-scan failed
[ 6.048978] event-scan failed
[ 6.061045] event-scan failed
[ 6.816978] event-scan failed
[ 6.829012] event-scan failed
[ 6.840953] event-scan failed
[ 6.853048] event-scan failed
[ 6.856977] event-scan failed
[ 6.872951] event-scan failed
[ 6.880956] event-scan failed
[ 6.888944] event-scan failed
[ 6.896956] event-scan failed
[ 6.904949] event-scan failed
[ 6.913078] event-scan failed
[ 6.921293] event-scan failed
[ 6.928951] event-scan failed
[ 6.936946] event-scan failed
[ 6.944954] event-scan failed
[ 6.952960] event-scan failed
[ 6.960944] event-scan failed
[ 6.968954] event-scan failed
[ 6.976954] event-scan failed
[ 6.984956] event-scan failed
[ 6.995755] event-scan failed
[ 7.004986] event-scan failed
[ 7.015689] event-scan failed
[ 7.024996] event-scan failed
[ 7.032960] event-scan failed
[ 7.040951] event-scan failed
[ 7.048945] event-scan failed
[ 7.057011] event-scan failed
[

On Mon, 2011-06-20 at 22:28 +0800, Andrew Buckeridge wrote:
> On Mon, 20 Jun 2011 05:49:57 +0100
> Ben Hutchings <ben@decadent.org.uk> wrote:
>
> > Can you please use http://snapshot.debian.org/package/linux-2.6/ to find
> > which was the last working version?
>
> linux-image-2.6.32-5-powerpc_2.6.32-34squeeze1_powerpc.deb
> Quiet see dmesg.0 attached.
>
> linux-image-2.6.32-5-powerpc_2.6.32-35_powerpc.deb
> Quiet see dmesg.2 attached.
>
> linux-image-2.6.33-2-powerpc_2.6.33-1~experimental.5_powerpc.deb
> Booted, but lots of "event-scan failed". See dmesg.1 attached.

That seems to be a firmware bug on the Pegasos, but there is a
workaround for it since Linux 2.6.35.

> I could not find any powerpc builds between these.
>
> linux-image-2.6.36-trunk-powerpc_2.6.36-1~experimental.1_powerpc.deb
> linux-image-2.6.37-1-powerpc_2.6.37-1_powerpc.deb
> linux-image-2.6.37-2-powerpc_2.6.37-2_powerpc.deb
> These failed to boot. In all cases stuck at the spinner.

At a guess, this may be fixed by a change in Linux 3.0-rc1:

commit 2c78027a62ea38585da1ff944afdc6146335cb7c
Author: Gabriel Paubert <paubert@iram.es>
Date: Fri May 13 01:03:13 2011 +0000

powerpc: Fix for Pegasos keyboard and mouse

This refers to a change made in Linux 2.6.36.

Please can you test Linux 3.0-rc3, currently available in experimental?

Ben.

--
Ben Hutchings
I'm always amazed by the number of people who take up solipsism because
they heard someone else explain it. - E*Borg on alt.fan.pratchett

Package: linux-image-3.0.0-rc3-powerpc
Version: 3.0.0~rc3-1~experimental.1

On Wed, 22 Jun 2011 04:01:38 +0100
Ben Hutchings <ben@decadent.org.uk> wrote:

> > linux-image-2.6.36-trunk-powerpc_2.6.36-1~experimental.1_powerpc.deb
> > linux-image-2.6.37-1-powerpc_2.6.37-1_powerpc.deb
> > linux-image-2.6.37-2-powerpc_2.6.37-2_powerpc.deb
> > These failed to boot. In all cases stuck at the spinner.
>
> At a guess, this may be fixed by a change in Linux 3.0-rc1:

> Please can you test Linux 3.0-rc3, currently available in experimental?

linux-image-3.0.0-rc3-powerpc_3.0.0~rc3-1~experimental.1_powerpc.deb
Also failed to boot and got stuck at spinner.



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110623203654.04f151e1.andrewb@zagam.net">http://lists.debian.org/20110623203654.04f151e1.andrewb@zagam.net

Package: linux-image-3.0.0-rc3-powerpc
Version: 3.0.0~rc3-1~experimental.1

Firmware boot command line is: --

vmlinuz-3.0.0-rc3-powerpc video=radeonfb:1400x1050-8@60 panic=60
root=UUID=39c3b58f-8331-4c14-828b-77eb1c2132df

I get this warning. Is it important? Is it related?

> +-----------+ Configuring linux-image-3.0.0-rc3-powerpc +-----------+
> | |
> | Required firmware files may be missing |
> | |
> | This system is currently running Linux 2.6.32-5-powerpc and you |
> | are installing Linux 3.0.0-rc3-powerpc. In the new version some |
> | of the drivers used on this system may require additional |
> | firmware files: |
> | |
> | radeon: radeon/SUMO2_me.bin, radeon/SUMO2_pfp.bin, |
> | radeon/SUMO_me.bin, radeon/SUMO_pfp.bin |
> | |
> | Most firmware files are not included in the system because they |
> | do not conform to the Debian Free Software Guidelines. You may |
> | need to reconfigure the package manager to include the contrib |
> | and non-free sections of the package archive before you can |
> | install these firmware files. |
> | |
> | <Ok> |
> | |
> +-------------------------------------------------------------------+

I suggest a <No, its not ok> button too.

Still get warning after I installed these packages: --

firmware-linux-free_3_all.deb
firmware-linux-nonfree_0.30_all.deb

$ fgrep radeon/SUMO /var/lib/dpkg/info/firmware-linux-nonfree.list
/lib/firmware/radeon/SUMO_rlc.bin

If radeon/SUMO2_me.bin, radeon/SUMO2_pfp.bin, radeon/SUMO_me.bin,
radeon/SUMO_pfp.bin are required how do I install them?



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110623211253.5cc9457f.andrewb@zagam.net">http://lists.debian.org/20110623211253.5cc9457f.andrewb@zagam.net

On Thu, Jun 23, 2011 at 09:12:53PM +0800, Andrew Buckeridge wrote:
> Package: linux-image-3.0.0-rc3-powerpc
> Version: 3.0.0~rc3-1~experimental.1
>
> Firmware boot command line is: --
>
> vmlinuz-3.0.0-rc3-powerpc video=radeonfb:1400x1050-8@60 panic=60
> root=UUID=39c3b58f-8331-4c14-828b-77eb1c2132df
>
> I get this warning. Is it important? Is it related?

No, not important.

[...]
> Still get warning after I installed these packages: --
>
> firmware-linux-free_3_all.deb
> firmware-linux-nonfree_0.30_all.deb
>
> $ fgrep radeon/SUMO /var/lib/dpkg/info/firmware-linux-nonfree.list
> /lib/firmware/radeon/SUMO_rlc.bin
>
> If radeon/SUMO2_me.bin, radeon/SUMO2_pfp.bin, radeon/SUMO_me.bin,
> radeon/SUMO_pfp.bin are required how do I install them?

They are not required unless you have some very new Radeon cards.
But I should add them to the firmware-linux-nonfree package.

Ben.

--
Ben Hutchings
We get into the habit of living before acquiring the habit of thinking.
- Albert Camus



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110623191200.GS29924@decadent.org.uk">http://lists.debian.org/20110623191200.GS29924@decadent.org.uk

On Thu, 2011-06-23 at 20:36 +0800, Andrew Buckeridge wrote:
> Package: linux-image-3.0.0-rc3-powerpc
> Version: 3.0.0~rc3-1~experimental.1
>
> On Wed, 22 Jun 2011 04:01:38 +0100
> Ben Hutchings <ben@decadent.org.uk> wrote:
>
> > > linux-image-2.6.36-trunk-powerpc_2.6.36-1~experimental.1_powerpc.deb
> > > linux-image-2.6.37-1-powerpc_2.6.37-1_powerpc.deb
> > > linux-image-2.6.37-2-powerpc_2.6.37-2_powerpc.deb
> > > These failed to boot. In all cases stuck at the spinner.
> >
> > At a guess, this may be fixed by a change in Linux 3.0-rc1:
>
> > Please can you test Linux 3.0-rc3, currently available in experimental?
>
> linux-image-3.0.0-rc3-powerpc_3.0.0~rc3-1~experimental.1_powerpc.deb
> Also failed to boot and got stuck at spinner.

Gabriel, Michael, do you recognise this bug? Are there any fixes for
Pegasos that are missing from 3.0-rc3?

Ben.

--
Ben Hutchings
If more than one person is responsible for a bug, no one is at fault.

On Sun, Jun 26, 2011 at 11:14:13PM +0100, Ben Hutchings wrote:
> On Thu, 2011-06-23 at 20:36 +0800, Andrew Buckeridge wrote:
> > Package: linux-image-3.0.0-rc3-powerpc
> > Version: 3.0.0~rc3-1~experimental.1
> >
> > On Wed, 22 Jun 2011 04:01:38 +0100
> > Ben Hutchings <ben@decadent.org.uk> wrote:
> >
> > > > linux-image-2.6.36-trunk-powerpc_2.6.36-1~experimental.1_powerpc.deb
> > > > linux-image-2.6.37-1-powerpc_2.6.37-1_powerpc.deb
> > > > linux-image-2.6.37-2-powerpc_2.6.37-2_powerpc.deb
> > > > These failed to boot. In all cases stuck at the spinner.
> > >
> > > At a guess, this may be fixed by a change in Linux 3.0-rc1:
> >
> > > Please can you test Linux 3.0-rc3, currently available in experimental?
> >
> > linux-image-3.0.0-rc3-powerpc_3.0.0~rc3-1~experimental.1_powerpc.deb
> > Also failed to boot and got stuck at spinner.
>
> Gabriel, Michael, do you recognise this bug? Are there any fixes for
> Pegasos that are missing from 3.0-rc3?

What do you mean by the spinner? I've had very long boot times with
an apparently dead machine depending on graphics options.

For now I'm running 2.6.39 with one patch for keyboard/mouse handling
which is now upstream.

I can try a more recent kernel on Thursday.

Gabriel



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110628125148.GA10884@iram.es">http://lists.debian.org/20110628125148.GA10884@iram.es

forwarded 630845 http://thread.gmane.org/gmane.linux.ports.ppc.embedded/43997
quit

Hi,

Gabriel Paubert wrote:
>>>> Andrew Buckeridge wrote:

>>>>> linux-image-2.6.36-trunk-powerpc_2.6.36-1~experimental.1_powerpc.deb
>>>>> linux-image-2.6.37-1-powerpc_2.6.37-1_powerpc.deb
>>>>> linux-image-2.6.37-2-powerpc_2.6.37-2_powerpc.deb
>>>>> These failed to boot. In all cases stuck at the spinner.
[...]
> What do you mean by the spinner? I've had very long boot times with
> an apparently dead machine depending on graphics options.
>
> For now I'm running 2.6.39 with one patch for keyboard/mouse handling
> which is now upstream.
>
> I can try a more recent kernel on Thursday.

Thanks. Please forgive my ignorance:

- Gabriel, what options do you suggest for a reasonably fast boot?
Does Debian's default configuration need corresponding changes?

- Andrew, what do you mean by the spinner? Could you take a photograph?

- Has anything changed in the month or so since this report was last
discussed?



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110805175314.GA17234@elie.gateway.2wire.net">htt p://lists.debian.org/20110805175314.GA17234@elie.gateway.2wire.net