FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 06-01-2011, 05:37 PM
Arnaud Gardelein
 
Default Bug#628832: linux-image-2.6.39-1-686-pae: Blank DVI output after resume when using KMS on RV250

Package: linux-2.6
Version: 2.6.39-1
Severity: normal

Tried s2ram from console with parameters suggested in:
http://old-en.opensuse.org/S2ram

Result: for all configurations, DVI output is black, but monitor is still
active, just black screen. Same result with boot option radeon.agpmode=-1

Did some googling and found this thread:
https://bugzilla.kernel.org/show_bug.cgi?id=16140
But in the case described there the output is garbled.

bomberx# s2ram -n
Machine unknown
This machine can be identified by:
sys_vendor = "ASUSTeK Computer INC."
sys_product = "A7N8X-E"
sys_version = "REV 2.xx"
bios_version = "ASUS A7N8X-E Deluxe ACPI BIOS Rev 1012 "

Before suspend:
bomberx% xrandr -q # This is before switching to the console to issue the
s2ram command
Screen 0: minimum 320 x 200, current 2560 x 1024, maximum 4096 x 4096
VGA-0 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm
x 301mm
1280x1024 60.0*+ 75.0
1280x960 60.0
1280x800 74.9 59.8
1152x864 75.0
1024x768 75.1 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
DVI-0 connected 1280x1024+1280+0 (normal left inverted right x axis y axis)
376mm x 301mm
1280x1024 60.0*+ 75.0
1280x960 60.0
1280x800 74.9 59.8
1152x864 75.0
1024x768 75.1 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
S-video disconnected (normal left inverted right x axis y axis)

bomberx% lspci -vv
(...)
03:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO]
(rev 01) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device 9994
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at da000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon

03:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 PRO]
(Secondary) (rev 01)
Subsystem: Micro-Star International Co., Ltd. Device 9995
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at db010000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: <access denied>

After resume:
Attached dmesg output contains the suspend and resume logs. Attached also lspci
-vv output.

bomberx% xrandr -q
Screen 0: minimum 320 x 200, current 2560 x 1024, maximum 4096 x 4096
VGA-0 connected 1280x1024+0+0 (normal left inverted right x axis y axis) 376mm
x 301mm
1280x1024 60.0*+ 75.0
1280x960 60.0
1280x800 74.9 59.8
1152x864 75.0
1024x768 75.1 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
DVI-0 connected 1280x1024+1280+0 (normal left inverted right x axis y axis)
376mm x 301mm
1280x1024 60.0*+ 75.0
1280x960 60.0
1280x800 74.9 59.8
1152x864 75.0
1024x768 75.1 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
S-video disconnected (normal left inverted right x axis y axis)





-- Package-specific info:
** Version:
Linux version 2.6.39-1-686-pae (Debian 2.6.39-1) (maks@debian.org) (gcc version 4.4.6 (Debian 4.4.6-3) ) #1 SMP Fri May 20 20:40:05 UTC 2011

** Command line:
BOOT_IMAGE=/vmlinuz-2.6.39-1-686-pae root=/dev/sda8 ro

** Not tainted

** Kernel log:
[ 14.852410] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[ 14.864343] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[ 14.876334] intel8x0_measure_ac97_clock: measured 61047 usecs (2960 samples)
[ 14.888103] intel8x0: clocking to 48000
[ 14.899834] bttv0: gpio: en=00000000, out=00000000 in=00ff27ff [init]
[ 14.900148] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 14.912282] bttv0: miro: id=9 tuner=3 radio=no stereo=no
[ 14.923660] bttv0: tuner type=3
[ 14.947558] IR Sony protocol handler initialized
[ 15.103784] lirc_dev: IR Remote Control driver registered, major 249
[ 15.349624] i2c-core: driver [msp3400] using legacy suspend method
[ 15.360405] i2c-core: driver [msp3400] using legacy resume method
[ 15.401119] IR LIRC bridge handler initialized
[ 15.456439] bttv0: audio absent, no audio device found!
[ 15.572259] i2c-core: driver [tuner] using legacy suspend method
[ 15.582614] i2c-core: driver [tuner] using legacy resume method
[ 15.699810] All bytes are equal. It is not a TEA5767
[ 15.709806] tuner 7-0060: Tuner -1 found with type(s) Radio TV.
[ 15.808855] tuner-simple 7-0060: creating new instance
[ 15.818539] tuner-simple 7-0060: type set to 3 (Philips (SECAM+PAL_BG) (FI1216MF, FM1216MF, FR1216MF))
[ 15.829452] bttv0: registered device video0
[ 15.840894] bttv0: registered device vbi0
[ 15.850260] bttv0: PLL: 28636363 => 35468950 .. ok
[ 16.903564] Adding 610400k swap on /dev/sda10. Priority:-1 extents:1 across:610400k
[ 17.253551] EXT3-fs (sda8): using internal journal
[ 17.549464] lp0: using parport0 (interrupt-driven).
[ 17.673339] Uniform Multi-Platform E-IDE driver
[ 17.791174] ide-cd driver 5.00
[ 17.838572] ide-gd driver 1.18
[ 17.901771] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[ 20.711344] EXT3-fs: barriers not enabled
[ 20.740319] kjournald starting. Commit interval 5 seconds
[ 20.746703] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 20.753516] EXT3-fs (sda1): using internal journal
[ 20.760031] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 20.839759] EXT3-fs: barriers not enabled
[ 20.855433] kjournald starting. Commit interval 5 seconds
[ 20.862060] EXT3-fs (dm-3): warning: maximal mount count reached, running e2fsck is recommended
[ 20.869145] EXT3-fs (dm-3): using internal journal
[ 20.875964] EXT3-fs (dm-3): mounted filesystem with ordered data mode
[ 20.901760] EXT3-fs: barriers not enabled
[ 20.916037] kjournald starting. Commit interval 5 seconds
[ 20.923029] EXT3-fs (dm-1): using internal journal
[ 20.929641] EXT3-fs (dm-1): mounted filesystem with ordered data mode
[ 20.952321] EXT3-fs: barriers not enabled
[ 20.967640] kjournald starting. Commit interval 5 seconds
[ 20.974582] EXT3-fs (dm-2): using internal journal
[ 20.981250] EXT3-fs (dm-2): mounted filesystem with ordered data mode
[ 21.098948] EXT3-fs: barriers not enabled
[ 21.108538] kjournald starting. Commit interval 5 seconds
[ 21.121434] EXT3-fs (dm-0): using internal journal
[ 21.128297] EXT3-fs (dm-0): mounted filesystem with ordered data mode
[ 21.280180] EXT3-fs: barriers not enabled
[ 21.324767] kjournald starting. Commit interval 5 seconds
[ 21.337506] EXT3-fs (dm-4): using internal journal
[ 21.364082] EXT3-fs (dm-4): mounted filesystem with ordered data mode
[ 24.062190] RPC: Registered udp transport module.
[ 24.076367] RPC: Registered tcp transport module.
[ 24.083337] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 24.163820] FS-Cache: Loaded
[ 24.233094] FS-Cache: Netfs 'nfs' registered for caching
[ 24.267127] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 26.247493] fuse init (API version 7.16)
[ 26.530940] ttyS0: LSR safety check engaged!
[ 26.532888] ttyS0: LSR safety check engaged!
[ 26.542735] ttyS2: LSR safety check engaged!
[ 26.544577] ttyS2: LSR safety check engaged!
[ 26.546854] ttyS3: LSR safety check engaged!
[ 26.548679] ttyS3: LSR safety check engaged!
[ 26.865238] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 28.455885] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 28.498646] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 29.035471] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 29.037639] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 29.037841] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 29.221848] xt_time: kernel timezone is +0200
[ 29.945592] u32 classifier
[ 29.945680] Performance counters on
[ 29.945780] input device check on
[ 29.945875] Actions configured
[ 34.678666] Bluetooth: Core ver 2.16
[ 34.678831] NET: Registered protocol family 31
[ 34.678948] Bluetooth: HCI device and connection manager initialized
[ 34.679117] Bluetooth: HCI socket layer initialized
[ 34.679246] Bluetooth: L2CAP socket layer initialized
[ 34.679931] Bluetooth: SCO socket layer initialized
[ 34.693688] Bluetooth: RFCOMM TTY layer initialized
[ 34.693839] Bluetooth: RFCOMM socket layer initialized
[ 34.693975] Bluetooth: RFCOMM ver 1.11
[ 34.732129] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 34.732286] Bluetooth: BNEP filters: protocol multicast
[ 36.740998] forcedeth 0000:00:04.0: eth5: no link during initialization
[ 36.741906] ADDRCONF(NETDEV_UP): eth5: link is not ready
[ 36.769124] skge 0000:01:04.0: eth1: enabling interface
[ 36.839202] 8139too 0000:01:08.0: eth2: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 38.851978] ppdev: user-space parallel port driver
[ 47.648016] eth1: no IPv6 routers present
[ 52.184252] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 52.201743] NFSD: starting 90-second grace period
[ 158.416016] eth1: no IPv6 routers present

** Model information
not available

** Loaded modules:
Module Size Used by
mperf 12387 0
cpufreq_conservative 12987 0
cpufreq_userspace 12520 0
cpufreq_stats 12670 0
cpufreq_powersave 12422 0
ppdev 12621 0
bnep 17147 2
rfcomm 31961 0
bluetooth 92361 10 bnep,rfcomm
rfkill 18510 3 bluetooth
crc16 12327 1 bluetooth
binfmt_misc 12778 1
xt_mac 12387 10
cls_u32 12816 0
sch_htb 17475 0
sch_ingress 12648 0
sch_sfq 12910 0
xt_time 12419 0
xt_connlimit 12498 0
xt_helper 12459 0
xt_realm 12391 0
xt_NFQUEUE 12488 0
xt_tcpmss 12393 0
xt_tcpudp 12471 45
xt_addrtype 12501 2
xt_pkttype 12395 0
iptable_raw 12476 0
xt_TPROXY 12702 0
nf_tproxy_core 12380 1 xt_TPROXY,[permanent]
ip6_tables 17069 1 xt_TPROXY
nf_defrag_ipv6 12661 1 xt_TPROXY
xt_CLASSIFY 12397 0
xt_mark 12413 1
xt_hashlimit 12948 0
xt_comment 12395 25
xt_length 12420 0
xt_connmark 12565 0
xt_owner 12391 0
xt_recent 12862 0
xt_iprange 12456 0
xt_physdev 12428 0
xt_policy 12458 0
xt_multiport 12470 6
iptable_mangle 12488 1
xt_conntrack 12567 18
ipt_ULOG 12561 0
ipt_REJECT 12425 4
ipt_REDIRECT 12431 0
ipt_NETMAP 12425 0
ipt_MASQUERADE 12530 0
ipt_LOG 12533 11
ipt_ECN 12416 0
ipt_ecn 12416 0
ipt_CLUSTERIP 12835 0
ipt_ah 12413 0
iptable_nat 12800 0
nf_nat 17733 4 ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 13649 21 iptable_nat,nf_nat
nf_conntrack 42465 9 xt_connlimit,xt_helper,xt_connmark,xt_conntrack,ip t_MASQUERADE,ipt_CLUSTERIP,iptable_nat,nf_nat,nf_c onntrack_ipv4
nf_defrag_ipv4 12443 2 xt_TPROXY,nf_conntrack_ipv4
iptable_filter 12488 1
ip_tables 16998 4 iptable_raw,iptable_mangle,iptable_nat,iptable_fil ter
x_tables 17969 40 xt_mac,xt_time,xt_connlimit,xt_helper,xt_realm,xt_ NFQUEUE,xt_tcpmss,xt_tcpudp,xt_addrtype,xt_pkttype ,iptable_raw,xt_TPROXY,ip6_tables,xt_CLASSIFY,xt_m ark,xt_hashlimit,xt_comment,xt_length,xt_connmark, xt_owner,xt_recent,xt_iprange,xt_physdev,xt_policy ,xt_multiport,iptable_mangle,xt_conntrack,ipt_ULOG ,ipt_REJECT,ipt_REDIRECT,ipt_NETMAP,ipt_MASQUERADE ,ipt_LOG,ipt_ECN,ipt_ecn,ipt_CLUSTERIP,ipt_ah,ipta ble_nat,iptable_filter,ip_tables
fuse 55666 1
nfsd 196206 13
nfs 219235 0
lockd 60891 2 nfsd,nfs
fscache 31438 1 nfs
auth_rpcgss 31819 2 nfsd,nfs
nfs_acl 12463 2 nfsd,nfs
sunrpc 137017 19 nfsd,nfs,lockd,auth_rpcgss,nfs_acl
eeprom 12481 0
asb100 13288 0
hwmon_vid 12364 1 asb100
firewire_sbp2 17514 0
psmouse 45863 0
ide_generic 8209 0 [permanent]
ide_gd_mod 27391 0
ide_cd_mod 30180 0
ide_core 65519 3 ide_generic,ide_gd_mod,ide_cd_mod
lp 12858 0
tuner_simple 16926 1
tuner_types 12305 1 tuner_simple
tea5767 12653 0
tuner 17237 1
tvaudio 26237 0
tda7432 12584 0
ir_lirc_codec 12651 0
msp3400 25815 0
lirc_dev 12797 1 ir_lirc_codec
ir_sony_decoder 12403 0
ir_jvc_decoder 12401 0
bttv 92077 0
ir_rc6_decoder 12401 0
ir_rc5_decoder 12401 0
ir_nec_decoder 12401 0
snd_intel8x0 22287 2
snd_ac97_codec 83732 1 snd_intel8x0
videobuf_dma_sg 12992 1 bttv
ac97_bus 12462 1 snd_ac97_codec
videobuf_core 17540 2 bttv,videobuf_dma_sg
btcx_risc 12499 1 bttv
rc_core 17813 7 ir_lirc_codec,ir_sony_decoder,ir_jvc_decoder,ir_rc 6_decoder,bttv,ir_rc5_decoder,ir_nec_decoder
tveeprom 16473 1 bttv
snd_wavefront 30608 0
v4l2_common 13026 5 tuner,tvaudio,tda7432,msp3400,bttv
snd_cs4236 26314 0
snd_cmipci 27787 2
snd_wss_lib 22401 2 snd_wavefront,snd_cs4236
snd_bt87x 13169 1
videodev 61226 6 tuner,tvaudio,tda7432,msp3400,bttv,v4l2_common
snd_pcm_oss 35864 0
snd_opl3_lib 13141 3 snd_wavefront,snd_cs4236,snd_cmipci
snd_mixer_oss 17649 1 snd_pcm_oss
snd_hwdep 12906 2 snd_wavefront,snd_opl3_lib
snd_mpu401 12592 0
snd_mpu401_uart 13299 4 snd_wavefront,snd_cs4236,snd_cmipci,snd_mpu401
snd_pcm 52731 7 snd_intel8x0,snd_ac97_codec,snd_cs4236,snd_wss_lib ,snd_bt87x,snd_cmipci,snd_pcm_oss
snd_seq_midi 12744 0
media 13692 1 videodev
snd_rawmidi 22407 3 snd_wavefront,snd_mpu401_uart,snd_seq_midi
snd_seq_midi_event 13124 1 snd_seq_midi
snd_seq 39172 2 snd_seq_midi,snd_seq_midi_event
snd_timer 22171 4 snd_wss_lib,snd_opl3_lib,snd_pcm,snd_seq
snd_seq_device 12995 4 snd_opl3_lib,snd_seq_midi,snd_rawmidi,snd_seq
shpchp 26653 0
i2c_nforce2 12520 0
snd 38189 28 snd_intel8x0,snd_ac97_codec,snd_wavefront,snd_cs42 36,snd_wss_lib,snd_bt87x,snd_cmipci,snd_opl3_lib,s nd_pcm_oss,snd_mixer_oss,snd_hwdep,snd_mpu401,snd_ mpu401_uart,snd_pcm,snd_rawmidi,snd_seq,snd_timer, snd_seq_device
snd_page_alloc 12841 4 snd_intel8x0,snd_bt87x,snd_wss_lib,snd_pcm
pci_hotplug 26303 1 shpchp
evdev 13084 7
pcspkr 12515 0
ns558 12417 0
gameport 13332 3 snd_cmipci,ns558
soundcore 12878 1 snd
parport_pc 21895 1
processor 26983 0
parport 27018 3 ppdev,lp,parport_pc
thermal_sys 17667 1 processor
button 12783 0
ext3 102125 7
jbd 40818 1 ext3
mbcache 12810 1 ext3
dm_mirror 17249 0
dm_region_hash 13072 1 dm_mirror
dm_log 13269 2 dm_mirror,dm_region_hash
dm_mod 56401 24 dm_mirror,dm_log
radeon 712176 2
ttm 46736 1 radeon
drm_kms_helper 26550 1 radeon
drm 129190 4 radeon,ttm,drm_kms_helper
i2c_algo_bit 12706 2 bttv,radeon
i2c_core 19022 17 eeprom,asb100,tuner_simple,tea5767,tuner,tvaudio,t da7432,msp3400,bttv,tveeprom,v4l2_common,videodev, i2c_nforce2,radeon,drm_kms_helper,drm,i2c_algo_bit
power_supply 13283 1 radeon
usbhid 35206 0
usb_storage 34951 0
hid 59841 1 usbhid
sg 21385 0
uas 12975 0
sr_mod 17418 0
sd_mod 35060 8
cdrom 34631 2 ide_cd_mod,sr_mod
crc_t10dif 12332 1 sd_mod
ata_generic 12439 0
pata_amd 13076 0
sata_sil 12788 8
libata 132100 3 ata_generic,pata_amd,sata_sil
ohci_hcd 21898 0
scsi_mod 134453 7 firewire_sbp2,usb_storage,sg,uas,sr_mod,sd_mod,lib ata
8139too 21937 0
firewire_ohci 26332 0
ehci_hcd 34885 0
8139cp 22004 0
firewire_core 42365 2 firewire_sbp2,firewire_ohci
mii 12595 2 8139too,8139cp
crc_itu_t 12331 1 firewire_core
usbcore 99225 6 usbhid,usb_storage,uas,ohci_hcd,ehci_hcd
skge 39547 0
forcedeth 47955 0

** PCI devices:
00:00.0 Host bridge [0600]: nVidia Corporation nForce2 IGP2 [10de:01e0] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-nvidia

00:00.1 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 1 [10de:01eb] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.2 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 4 [10de:01ee] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.3 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 3 [10de:01ed] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.4 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 2 [10de:01ec] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.5 RAM memory [0500]: nVidia Corporation nForce2 Memory Controller 5 [10de:01ef] (rev c1)
Subsystem: ASUSTeK Computer Inc. Device [1043:80ac]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:01.0 ISA bridge [0601]: nVidia Corporation nForce2 ISA Bridge [10de:0060] (rev a4)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:80ad]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>

00:01.1 SMBus [0c05]: nVidia Corporation nForce2 SMBus (MCP) [10de:0064] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:0c11]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at dc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus

00:02.0 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at de086000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

00:02.1 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0067] (rev a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at de081000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd

00:02.2 USB Controller [0c03]: nVidia Corporation nForce2 USB Controller [10de:0068] (rev a4) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard [1043:0c11]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 21
Region 0: Memory at de082000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

00:04.0 Ethernet controller [0200]: nVidia Corporation nForce2 Ethernet Controller [10de:0066] (rev a1)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard onboard nForce2 Ethernet [1043:80a7]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at de083000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e000 [size=8]
Capabilities: <access denied>
Kernel driver in use: forcedeth

00:05.0 Multimedia audio controller [0401]: nVidia Corporation nForce Audio Processing Unit [10de:006b] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:0c11]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>

00:06.0 Multimedia audio controller [0401]: nVidia Corporation nForce2 AC97 Audio Controler (MCP) [10de:006a] (rev a1)
Subsystem: ASUSTeK Computer Inc. nForce2 AC97 Audio Controler (MCP) [1043:8095]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at e400 [size=256]
Region 1: I/O ports at d000 [size=128]
Region 2: Memory at de087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Intel ICH

00:08.0 PCI bridge [0604]: nVidia Corporation nForce2 External PCI Bridge [10de:006c] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-0000afff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-d8ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:09.0 IDE interface [0101]: nVidia Corporation nForce2 IDE [10de:0065] (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:0c11]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd

00:0d.0 FireWire (IEEE 1394) [0c00]: nVidia Corporation nForce2 FireWire (IEEE 1394) Controller [10de:006e] (rev a3) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:809a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at de084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at de085000 (32-bit, non-prefetchable) [size=64]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci

00:1e.0 PCI bridge [0604]: nVidia Corporation nForce2 AGP [10de:01e8] (rev c1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: da000000-dbffffff
Prefetchable memory behind bridge: c8000000-d7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

01:04.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus) [1043:811a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at 9000 [size=256]
[virtual] Expansion ROM at d8020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge

01:07.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver) [11bd:0012]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: bttv

01:07.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio section) [11bd:0012]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d8001000 (32-bit, prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: Bt87x

01:08.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at dd004000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too

01:0a.0 Multimedia audio controller [0401]: C-Media Electronics Inc CM8738 [13f6:0111] (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device [13f6:0111]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9800 [size=256]
Capabilities: <access denied>
Kernel driver in use: C-Media PCI

01:0b.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller [1095:3112] (rev 02)
Subsystem: Silicon Image, Inc. SiI 3112 SATARaid Controller [1095:6112]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9c00 [size=8]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at a400 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at ac00 [size=16]
Region 5: Memory at dd005000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at d8080000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: sata_sil

03:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV280 [Radeon 9200 PRO] [1002:5960] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device [1462:9994]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at da000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeon

03:00.1 Display controller [0380]: ATI Technologies Inc RV280 [Radeon 9200 PRO] (Secondary) [1002:5940] (rev 01)
Subsystem: Micro-Star International Co., Ltd. Device [1462:9995]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at db010000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: <access denied>


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 058f:6362 Alcor Micro Corp. Flash Card Reader/Writer
Bus 002 Device 002: ID 046d:c05a Logitech, Inc. Optical Mouse M90


-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'stable')
Architecture: i386 (i686)

Kernel: Linux 2.6.39-1-686-pae (SMP w/1 CPU core)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.39-1-686-pae depends on:
ii debconf [debconf-2.0] 1.5.39 Debian configuration management sy
ii initramfs-tools [linux-initra 0.99 tools for generating an initramfs
ii linux-base 3.2 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
ii yaird [linux-initramfs-tool] 0.0.13-5 Yet Another mkInitRD

Versions of packages linux-image-2.6.39-1-686-pae recommends:
ii firmware-linux-free 3 Binary firmware for various driver
ii libc6-i686 2.13-4 Embedded GNU C Library: Shared lib

Versions of packages linux-image-2.6.39-1-686-pae suggests:
ii grub-pc 1.99-4 GRand Unified Bootloader, version
pn linux-doc-2.6.39 <none> (no description available)

Versions of packages linux-image-2.6.39-1-686-pae is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.30 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)

-- debconf information:
linux-image-2.6.39-1-686-pae/postinst/depmod-error-initrd-2.6.39-1-686-pae: false
linux-image-2.6.39-1-686-pae/postinst/ignoring-ramdisk:
* linux-image-2.6.39-1-686-pae/postinst/missing-firmware-2.6.39-1-686-pae:
linux-image-2.6.39-1-686-pae/prerm/removing-running-kernel-2.6.39-1-686-pae: true
00:00.0 Host bridge: nVidia Corporation nForce2 IGP2 (rev c1)
Subsystem: ASUSTeK Computer Inc. Device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [40] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
Capabilities: [60] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.16
Kernel driver in use: agpgart-nvidia

00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: ASUSTeK Computer Inc. Device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: ASUSTeK Computer Inc. Device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: ASUSTeK Computer Inc. Device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: ASUSTeK Computer Inc. Device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: ASUSTeK Computer Inc. Device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [48] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=1 UnitCnt=15 MastHost- DefDir-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC+ TXO- <CRCErr=0
Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO+ <CRCErr=0
Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
Revision ID: 0.00

00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 9
Region 0: I/O ports at dc00 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus

00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at de086000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd

00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at de081000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd

00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 20
Region 0: Memory at de082000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0080
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd

00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
Subsystem: ASUSTeK Computer Inc. A7N8X Mainboard onboard nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at de083000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e000 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: forcedeth

00:05.0 Multimedia audio controller: nVidia Corporation nForce Audio Processing Unit (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at de000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP) (rev a1)
Subsystem: ASUSTeK Computer Inc. nForce2 AC97 Audio Controler (MCP)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at e400 [size=256]
Region 1: I/O ports at d000 [size=128]
Region 2: Memory at de087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH

00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00009000-0000afff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-d8ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_amd

00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire (IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at de084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at de085000 (32-bit, non-prefetchable) [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: firewire_ohci

00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: da000000-dbffffff
Prefetchable memory behind bridge: c8000000-d7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

01:04.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at 9000 [size=256]
[virtual] Expansion ROM at d8020000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=7 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
Read-only fields:
[PN] Part number: Yukon 88E8001
[EC] Engineering changes: Rev. 1.3
[MN] Manufacture ID: 4d 61 72 76 65 6c 6c
[SN] Serial number: AbCdEfG334454
[CP] Extended capability: 01 10 cc 03
[RV] Reserved: checksum good, 10 byte(s) reserved
Read/write fields:
[RW] Read-write area: 121 byte(s) free
End
Kernel driver in use: skge

01:07.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
End
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: bttv

01:07.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Pinnacle Systems Inc. PCTV pro (TV + FM stereo receiver, audio section)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d8001000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
End
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Bt87x

01:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9400 [size=256]
Region 1: Memory at dd004000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: 8139too

01:0a.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 9800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: C-Media PCI

01:0b.0 RAID bus controller: Silicon Image, Inc. SiI 3112 [SATALink/SATARaid] Serial ATA Controller (rev 02)
Subsystem: Silicon Image, Inc. SiI 3112 SATARaid Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 9c00 [size=8]
Region 1: I/O ports at a000 [size=4]
Region 2: I/O ports at a400 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at ac00 [size=16]
Region 5: Memory at dd005000 (32-bit, non-prefetchable) [size=512]
[virtual] Expansion ROM at d8080000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: sata_sil

03:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Device 9994
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at db000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at da000000 [disabled] [size=128K]
Capabilities: [58] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=32 ArqSz=2 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x8
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: radeon

03:00.1 Display controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (Secondary) (rev 01)
Subsystem: Micro-Star International Co., Ltd. Device 9995
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at d0000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at db010000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
 
Old 06-03-2011, 04:09 AM
Ben Hutchings
 
Default Bug#628832: linux-image-2.6.39-1-686-pae: Blank DVI output after resume when using KMS on RV250

On Wed, 2011-06-01 at 19:37 +0200, Arnaud Gardelein wrote:
> Package: linux-2.6
> Version: 2.6.39-1
> Severity: normal
>
> Tried s2ram from console with parameters suggested in:
> http://old-en.opensuse.org/S2ram
[...]

That information is obsolete if you're using KMS.

Please test with 'echo mem > /sys/power/state' first.

Ben.

--
Ben Hutchings
Once a job is fouled up, anything done to improve it makes it worse.
 
Old 06-06-2011, 06:07 PM
Arnaud Gardelein
 
Default Bug#628832: linux-image-2.6.39-1-686-pae: Blank DVI output after resume when using KMS on RV250

Le vendredi 03 juin 2011 à 05:09 +0100, Ben Hutchings a écrit :
> Please test with 'echo mem > /sys/power/state' first.

Tested, same result: blank DVI output. Attached dmesg output.

Arnaud.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.39-1-686-pae (Debian 2.6.39-1) (maks@debian.org) (gcc version 4.4.6 (Debian 4.4.6-3) ) #1 SMP Fri May 20 20:40:05 UTC 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000005fff0000 (usable)
[ 0.000000] BIOS-e820: 000000005fff0000 - 000000005fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000005fff3000 - 0000000060000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection missing in CPU!
[ 0.000000] DMI 2.2 present.
[ 0.000000] DMI: ASUSTeK Computer INC. A7N8X-E/A7N8X-E, BIOS ASUS A7N8X-E Deluxe ACPI BIOS Rev 1012 08/04/2004
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x5fff0 max_arch_pfn = 0x1000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-AFFFF uncachable
[ 0.000000] B0000-BFFFF write-combining
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 040000000 mask FE0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FF8000000 write-combining
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01a00000
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[ 0.000000] 0000000000 - 0000200000 page 4k
[ 0.000000] 0000200000 - 0037800000 page 2M
[ 0.000000] 0037800000 - 00379fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[ 0.000000] RAMDISK: 36ab6000 - 37553000
[ 0.000000] ACPI: RSDP 000f75e0 00014 (v00 Nvidia)
[ 0.000000] ACPI: RSDT 5fff3000 0002C (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: FACP 5fff3040 00074 (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: DSDT 5fff30c0 04561 (v01 NVIDIA AWRDACPI 00001000 MSFT 0100000E)
[ 0.000000] ACPI: FACS 5fff0000 00040
[ 0.000000] ACPI: APIC 5fff7640 0006E (v01 Nvidia AWRDACPI 42302E31 AWRD 00000000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 645MB HIGHMEM available.
[ 0.000000] 889MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 379fe000
[ 0.000000] low ram: 0 - 379fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000379fe
[ 0.000000] HighMem 0x000379fe -> 0x0005fff0
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0005fff0
[ 0.000000] On node 0 totalpages: 393087
[ 0.000000] free_area_init_node: node 0, pgdat c14167c0, node_mem_map f5eb6200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1748 pages used for memmap
[ 0.000000] Normal zone: 221994 pages, LIFO batch:31
[ 0.000000] HighMem zone: 1292 pages used for memmap
[ 0.000000] HighMem zone: 164070 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] Nvidia board detected. Ignoring ACPI timer override.
[ 0.000000] If you got timer trouble try acpi_use_timer_override
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: BIOS IRQ0 pin2 override ignored.
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ14 used by override.
[ 0.000000] ACPI: IRQ15 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 60000000 (gap: 60000000:9ec00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 13 pages/cpu @f7600000 s30976 r0 d22272 u2097152
[ 0.000000] pcpu-alloc: s30976 r0 d22272 u2097152 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 390015
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.39-1-686-pae root=/dev/sda8 ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 6290944 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000379fe:0005fff0)
[ 0.000000] Memory: 1536864k/1572800k available (2784k kernel code, 35484k reserved, 1428k data, 436k init, 661448k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd36000 - 0xfffff000 (2852 kB)
[ 0.000000] pkmap : 0xffa00000 - 0xffc00000 (2048 kB)
[ 0.000000] vmalloc : 0xf81fe000 - 0xff9fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf79fe000 ( 889 MB)
[ 0.000000] .init : 0xc141e000 - 0xc148b000 ( 436 kB)
[ 0.000000] .data : 0xc12b8100 - 0xc141d240 (1428 kB)
[ 0.000000] .text : 0xc1000000 - 0xc12b8100 (2784 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:1280
[ 0.000000] CPU 0 irqstacks, hard=f540a000 soft=f540c000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1746.865 MHz processor.
[ 0.008004] Calibrating delay loop (skipped), value calculated using timer frequency.. 3493.73 BogoMIPS (lpj=6987460)
[ 0.008099] pid_max: default: 32768 minimum: 301
[ 0.008216] Security Framework initialized
[ 0.008267] SELinux: Disabled at boot.
[ 0.008342] Mount-cache hash table entries: 512
[ 0.008789] Initializing cgroup subsys ns
[ 0.008839] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.008899] Initializing cgroup subsys cpuacct
[ 0.008974] Initializing cgroup subsys memory
[ 0.009037] Initializing cgroup subsys devices
[ 0.009084] Initializing cgroup subsys freezer
[ 0.009130] Initializing cgroup subsys net_cls
[ 0.009176] Initializing cgroup subsys blkio
[ 0.009267] mce: CPU supports 4 MCE banks
[ 0.009738] SMP alternatives: switching to UP code
[ 0.016091] Freeing SMP alternatives: 16k freed
[ 0.016155] ACPI: Core revision 20110316
[ 0.019891] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.020338] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.060076] CPU0: AMD Sempron(tm) 2500+ stepping 01
[ 0.064003] Performance Events: AMD PMU driver.
[ 0.064003] ... version: 0
[ 0.064003] ... bit width: 48
[ 0.064003] ... generic registers: 4
[ 0.064003] ... value mask: 0000ffffffffffff
[ 0.064003] ... max period: 00007fffffffffff
[ 0.064003] ... fixed-purpose events: 0
[ 0.064003] ... event mask: 000000000000000f
[ 0.064003] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.064003] Brought up 1 CPUs
[ 0.064003] Total of 1 processors activated (3493.73 BogoMIPS).
[ 0.064003] devtmpfs: initialized
[ 0.064003] PM: Registering ACPI NVS region at 5fff0000 (12288 bytes)
[ 0.064003] print_constraints: dummy:
[ 0.064003] NET: Registered protocol family 16
[ 0.064003] ACPI: bus type pci registered
[ 0.094775] PCI: PCI BIOS revision 2.10 entry at 0xfb410, last bus=3
[ 0.094824] PCI: Using configuration type 1 for base access
[ 0.095635] bio: create slab <bio-0> at 0
[ 0.096798] ACPI: EC: Look up EC in DSDT
[ 0.100748] ACPI: Interpreter enabled
[ 0.100802] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.101029] ACPI: Using IOAPIC for interrupt routing
[ 0.107718] ACPI: No dock devices found.
[ 0.107770] HEST: Table not found.
[ 0.107819] PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug
[ 0.107962] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.108169] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
[ 0.108174] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
[ 0.108179] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored)
[ 0.108183] pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored)
[ 0.108187] pci_root PNP0A03:00: host bridge window [mem 0x60000000-0xfebfffff] (ignored)
[ 0.108208] pci 0000:00:00.0: [10de:01e0] type 0 class 0x000600
[ 0.108218] pci 0000:00:00.0: reg 10: [mem 0xc0000000-0xc7ffffff pref]
[ 0.108237] pci 0000:00:00.0: nForce2 C1 Halt Disconnect fixup
[ 0.108313] pci 0000:00:00.1: [10de:01eb] type 0 class 0x000500
[ 0.108352] pci 0000:00:00.2: [10de:01ee] type 0 class 0x000500
[ 0.108391] pci 0000:00:00.3: [10de:01ed] type 0 class 0x000500
[ 0.108428] pci 0000:00:00.4: [10de:01ec] type 0 class 0x000500
[ 0.108467] pci 0000:00:00.5: [10de:01ef] type 0 class 0x000500
[ 0.108511] pci 0000:00:01.0: [10de:0060] type 0 class 0x000601
[ 0.108591] pci 0000:00:01.1: [10de:0064] type 0 class 0x000c05
[ 0.108606] pci 0000:00:01.1: reg 10: [io 0xdc00-0xdc1f]
[ 0.108659] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.108665] pci 0000:00:01.1: PME# disabled
[ 0.108689] pci 0000:00:02.0: [10de:0067] type 0 class 0x000c03
[ 0.108704] pci 0000:00:02.0: reg 10: [mem 0xde086000-0xde086fff]
[ 0.108756] pci 0000:00:02.0: supports D1 D2
[ 0.108759] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.108764] pci 0000:00:02.0: PME# disabled
[ 0.108784] pci 0000:00:02.1: [10de:0067] type 0 class 0x000c03
[ 0.108799] pci 0000:00:02.1: reg 10: [mem 0xde081000-0xde081fff]
[ 0.108850] pci 0000:00:02.1: supports D1 D2
[ 0.108854] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.108859] pci 0000:00:02.1: PME# disabled
[ 0.108880] pci 0000:00:02.2: [10de:0068] type 0 class 0x000c03
[ 0.108897] pci 0000:00:02.2: reg 10: [mem 0xde082000-0xde0820ff]
[ 0.108954] pci 0000:00:02.2: supports D1 D2
[ 0.108958] pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.108963] pci 0000:00:02.2: PME# disabled
[ 0.108990] pci 0000:00:04.0: [10de:0066] type 0 class 0x000200
[ 0.109005] pci 0000:00:04.0: reg 10: [mem 0xde083000-0xde083fff]
[ 0.109015] pci 0000:00:04.0: reg 14: [io 0xe000-0xe007]
[ 0.109061] pci 0000:00:04.0: supports D1 D2
[ 0.109064] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.109069] pci 0000:00:04.0: PME# disabled
[ 0.109088] pci 0000:00:05.0: [10de:006b] type 0 class 0x000401
[ 0.109103] pci 0000:00:05.0: reg 10: [mem 0xde000000-0xde07ffff]
[ 0.109154] pci 0000:00:05.0: supports D1 D2
[ 0.109174] pci 0000:00:06.0: [10de:006a] type 0 class 0x000401
[ 0.109189] pci 0000:00:06.0: reg 10: [io 0xe400-0xe4ff]
[ 0.109198] pci 0000:00:06.0: reg 14: [io 0xd000-0xd07f]
[ 0.109208] pci 0000:00:06.0: reg 18: [mem 0xde087000-0xde087fff]
[ 0.109248] pci 0000:00:06.0: supports D1 D2
[ 0.109265] pci 0000:00:08.0: [10de:006c] type 1 class 0x000604
[ 0.109306] pci 0000:00:09.0: [10de:0065] type 0 class 0x000101
[ 0.109345] pci 0000:00:09.0: reg 20: [io 0xf000-0xf00f]
[ 0.109392] pci 0000:00:0d.0: [10de:006e] type 0 class 0x000c00
[ 0.109407] pci 0000:00:0d.0: reg 10: [mem 0xde084000-0xde0847ff]
[ 0.109417] pci 0000:00:0d.0: reg 14: [mem 0xde085000-0xde08503f]
[ 0.109462] pci 0000:00:0d.0: supports D1 D2
[ 0.109466] pci 0000:00:0d.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.109470] pci 0000:00:0d.0: PME# disabled
[ 0.109502] pci 0000:00:1e.0: [10de:01e8] type 1 class 0x000604
[ 0.109561] pci 0000:01:04.0: [11ab:4320] type 0 class 0x000200
[ 0.109584] pci 0000:01:04.0: reg 10: [mem 0xdd000000-0xdd003fff]
[ 0.109597] pci 0000:01:04.0: reg 14: [io 0x9000-0x90ff]
[ 0.109645] pci 0000:01:04.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.109671] pci 0000:01:04.0: supports D1 D2
[ 0.109674] pci 0000:01:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.109681] pci 0000:01:04.0: PME# disabled
[ 0.109711] pci 0000:01:07.0: [109e:036e] type 0 class 0x000400
[ 0.109734] pci 0000:01:07.0: reg 10: [mem 0xd8000000-0xd8000fff pref]
[ 0.109835] pci 0000:01:07.1: [109e:0878] type 0 class 0x000480
[ 0.109858] pci 0000:01:07.1: reg 10: [mem 0xd8001000-0xd8001fff pref]
[ 0.109966] pci 0000:01:08.0: [10ec:8139] type 0 class 0x000200
[ 0.109986] pci 0000:01:08.0: reg 10: [io 0x9400-0x94ff]
[ 0.109999] pci 0000:01:08.0: reg 14: [mem 0xdd004000-0xdd0040ff]
[ 0.110064] pci 0000:01:08.0: supports D1 D2
[ 0.110068] pci 0000:01:08.0: PME# supported from D1 D2 D3hot D3cold
[ 0.110074] pci 0000:01:08.0: PME# disabled
[ 0.110099] pci 0000:01:0a.0: [13f6:0111] type 0 class 0x000401
[ 0.110119] pci 0000:01:0a.0: reg 10: [io 0x9800-0x98ff]
[ 0.110196] pci 0000:01:0a.0: supports D1 D2
[ 0.110220] pci 0000:01:0b.0: [1095:3112] type 0 class 0x000104
[ 0.110240] pci 0000:01:0b.0: reg 10: [io 0x9c00-0x9c07]
[ 0.110253] pci 0000:01:0b.0: reg 14: [io 0xa000-0xa003]
[ 0.110266] pci 0000:01:0b.0: reg 18: [io 0xa400-0xa407]
[ 0.110279] pci 0000:01:0b.0: reg 1c: [io 0xa800-0xa803]
[ 0.110291] pci 0000:01:0b.0: reg 20: [io 0xac00-0xac0f]
[ 0.110304] pci 0000:01:0b.0: reg 24: [mem 0xdd005000-0xdd0051ff]
[ 0.110317] pci 0000:01:0b.0: reg 30: [mem 0x00000000-0x0007ffff pref]
[ 0.110338] pci 0000:01:0b.0: supports D1 D2
[ 0.110374] pci 0000:00:08.0: PCI bridge to [bus 01-01]
[ 0.110424] pci 0000:00:08.0: bridge window [io 0x9000-0xafff]
[ 0.110429] pci 0000:00:08.0: bridge window [mem 0xdc000000-0xddffffff]
[ 0.110435] pci 0000:00:08.0: bridge window [mem 0xd8000000-0xd8ffffff pref]
[ 0.110462] pci 0000:03:00.0: [1002:5960] type 0 class 0x000300
[ 0.110480] pci 0000:03:00.0: reg 10: [mem 0xc8000000-0xcfffffff pref]
[ 0.110490] pci 0000:03:00.0: reg 14: [io 0xc000-0xc0ff]
[ 0.110500] pci 0000:03:00.0: reg 18: [mem 0xdb000000-0xdb00ffff]
[ 0.110528] pci 0000:03:00.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.110550] pci 0000:03:00.0: supports D1 D2
[ 0.110572] pci 0000:03:00.1: [1002:5940] type 0 class 0x000380
[ 0.110587] pci 0000:03:00.1: reg 10: [mem 0xd0000000-0xd7ffffff pref]
[ 0.110597] pci 0000:03:00.1: reg 14: [mem 0xdb010000-0xdb01ffff]
[ 0.110644] pci 0000:03:00.1: supports D1 D2
[ 0.110686] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[ 0.110735] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff]
[ 0.110740] pci 0000:00:1e.0: bridge window [mem 0xda000000-0xdbffffff]
[ 0.110745] pci 0000:00:1e.0: bridge window [mem 0xc8000000-0xd7ffffff pref]
[ 0.110756] pci_bus 0000:00: on NUMA node 0
[ 0.110762] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.110874] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
[ 0.111115] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
[ 0.143235] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.143763] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.144277] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.144800] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.145323] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.145909] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.146430] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.146950] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.147470] ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 0.148026] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 0.148553] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.149140] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.149664] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.150185] ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[ 0.150705] ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.151289] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[ 0.151879] ACPI: PCI Interrupt Link [APC1] (IRQs *16)
[ 0.152068] ACPI: PCI Interrupt Link [APC2] (IRQs *17)
[ 0.152262] ACPI: PCI Interrupt Link [APC3] (IRQs *18)
[ 0.152454] ACPI: PCI Interrupt Link [APC4] (IRQs *19)
[ 0.152646] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 0.152907] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0
[ 0.153227] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0
[ 0.153544] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0
[ 0.153862] ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0
[ 0.154183] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0
[ 0.154501] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
[ 0.154822] ACPI: PCI Interrupt Link [APCS] (IRQs *23)
[ 0.155046] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0
[ 0.155364] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0
[ 0.155683] ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
[ 0.156059] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
[ 0.156527] vgaarb: device added: PCI:0000:03:00.0,decodes=io+mem,owns=io+mem,locks= none
[ 0.156587] vgaarb: loaded
[ 0.160072] PCI: Using ACPI for IRQ routing
[ 0.160146] PCI: pci_cache_line_size set to 32 bytes
[ 0.160254] reserve RAM buffer: 000000000009f800 - 000000000009ffff
[ 0.160259] reserve RAM buffer: 000000005fff0000 - 000000005fffffff
[ 0.162331] pnp: PnP ACPI init
[ 0.162408] ACPI: bus type pnp registered
[ 0.162768] pnp 00:00: [io 0x4000-0x407f]
[ 0.162773] pnp 00:00: [io 0x4080-0x40ff]
[ 0.162777] pnp 00:00: [io 0x4400-0x447f]
[ 0.162780] pnp 00:00: [io 0x4480-0x44ff]
[ 0.162783] pnp 00:00: [io 0x4200-0x427f]
[ 0.162786] pnp 00:00: [io 0x4280-0x42ff]
[ 0.162894] system 00:00: [io 0x4000-0x407f] has been reserved
[ 0.162944] system 00:00: [io 0x4080-0x40ff] has been reserved
[ 0.162993] system 00:00: [io 0x4400-0x447f] has been reserved
[ 0.163041] system 00:00: [io 0x4480-0x44ff] has been reserved
[ 0.163090] system 00:00: [io 0x4200-0x427f] has been reserved
[ 0.163138] system 00:00: [io 0x4280-0x42ff] has been reserved
[ 0.163188] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.163205] pnp 00:01: [io 0x5000-0x503f]
[ 0.163209] pnp 00:01: [io 0x5500-0x553f]
[ 0.163268] system 00:01: [io 0x5000-0x503f] has been reserved
[ 0.163318] system 00:01: [io 0x5500-0x553f] has been reserved
[ 0.163367] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.163540] pnp 00:02: [mem 0x000d8800-0x000dbfff]
[ 0.163545] pnp 00:02: [mem 0x000f0000-0x000f7fff]
[ 0.163549] pnp 00:02: [mem 0x000f8000-0x000fbfff]
[ 0.163552] pnp 00:02: [mem 0x000fc000-0x000fffff]
[ 0.163556] pnp 00:02: [mem 0x5fff0000-0x5fffffff]
[ 0.163559] pnp 00:02: [mem 0xffff0000-0xffffffff]
[ 0.163563] pnp 00:02: [mem 0x00000000-0x0009ffff]
[ 0.163566] pnp 00:02: [mem 0x00100000-0x5ffeffff]
[ 0.163570] pnp 00:02: [mem 0xfec00000-0xfec00fff]
[ 0.163573] pnp 00:02: [mem 0xfee00000-0xfee00fff]
[ 0.163647] system 00:02: [mem 0x000d8800-0x000dbfff] has been reserved
[ 0.163701] system 00:02: [mem 0x000f0000-0x000f7fff] could not be reserved
[ 0.163751] system 00:02: [mem 0x000f8000-0x000fbfff] could not be reserved
[ 0.163801] system 00:02: [mem 0x000fc000-0x000fffff] could not be reserved
[ 0.163851] system 00:02: [mem 0x5fff0000-0x5fffffff] could not be reserved
[ 0.163901] system 00:02: [mem 0xffff0000-0xffffffff] has been reserved
[ 0.163950] system 00:02: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.164000] system 00:02: [mem 0x00100000-0x5ffeffff] could not be reserved
[ 0.164030] system 00:02: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.164080] system 00:02: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.164130] system 00:02: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.164204] pnp 00:03: [bus 00-ff]
[ 0.164208] pnp 00:03: [io 0x0cf8-0x0cff]
[ 0.164212] pnp 00:03: [io 0x0000-0x0cf7 window]
[ 0.164216] pnp 00:03: [io 0x0d00-0xffff window]
[ 0.164220] pnp 00:03: [mem 0x000a0000-0x000bffff window]
[ 0.164224] pnp 00:03: [mem 0x000c0000-0x000dffff window]
[ 0.164227] pnp 00:03: [mem 0x60000000-0xfebfffff window]
[ 0.164324] pnp 00:03: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.164850] pnp 00:04: [io 0x0010-0x001f]
[ 0.164854] pnp 00:04: [io 0x0022-0x003f]
[ 0.164858] pnp 00:04: [io 0x0044-0x005f]
[ 0.164861] pnp 00:04: [io 0x0062-0x0063]
[ 0.164864] pnp 00:04: [io 0x0065-0x006f]
[ 0.164867] pnp 00:04: [io 0x0074-0x007f]
[ 0.164870] pnp 00:04: [io 0x0091-0x0093]
[ 0.164874] pnp 00:04: [io 0x00a2-0x00bf]
[ 0.164877] pnp 00:04: [io 0x00e0-0x00ef]
[ 0.164880] pnp 00:04: [io 0x04d0-0x04d1]
[ 0.164974] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.165025] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.165044] pnp 00:05: [dma 4]
[ 0.165048] pnp 00:05: [io 0x0000-0x000f]
[ 0.165051] pnp 00:05: [io 0x0080-0x0090]
[ 0.165055] pnp 00:05: [io 0x0094-0x009f]
[ 0.165058] pnp 00:05: [io 0x00c0-0x00df]
[ 0.165108] pnp 00:05: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.165125] pnp 00:06: [io 0x0070-0x0073]
[ 0.165142] pnp 00:06: [irq 8]
[ 0.165192] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.165206] pnp 00:07: [io 0x0061]
[ 0.165264] pnp 00:07: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.165280] pnp 00:08: [io 0x00f0-0x00ff]
[ 0.165287] pnp 00:08: [irq 13]
[ 0.165337] pnp 00:08: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.165623] pnp 00:09: [io 0x03f8-0x03ff]
[ 0.165631] pnp 00:09: [irq 4]
[ 0.165730] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.165955] pnp 00:0a: [io 0x02f8-0x02ff]
[ 0.165963] pnp 00:0a: [irq 3]
[ 0.166052] pnp 00:0a: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.166478] pnp 00:0b: [io 0x0378-0x037f]
[ 0.166482] pnp 00:0b: [io 0x0778-0x077b]
[ 0.166490] pnp 00:0b: [irq 7]
[ 0.166493] pnp 00:0b: [dma 3]
[ 0.166591] pnp 00:0b: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.166644] pnp 00:0c: [io 0x0060]
[ 0.166648] pnp 00:0c: [io 0x0064]
[ 0.166655] pnp 00:0c: [irq 1]
[ 0.166710] pnp 00:0c: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.166914] pnp 00:0d: [io 0x0330-0x0331]
[ 0.166922] pnp 00:0d: [irq 10]
[ 0.166994] pnp 00:0d: Plug and Play ACPI device, IDs PNPb006 (active)
[ 0.167178] pnp 00:0e: [io 0x0201]
[ 0.167245] pnp 00:0e: Plug and Play ACPI device, IDs PNPb02f (active)
[ 0.167255] pnp: PnP ACPI: found 15 devices
[ 0.167301] ACPI: ACPI bus type pnp unregistered
[ 0.167350] PnPBIOS: Disabled by ACPI PNP
[ 0.204552] Switching to clocksource acpi_pm
[ 0.204687] pci 0000:01:0b.0: BAR 6: assigned [mem 0xd8080000-0xd80fffff pref]
[ 0.204747] pci 0000:01:04.0: BAR 6: assigned [mem 0xd8020000-0xd803ffff pref]
[ 0.204805] pci 0000:00:08.0: PCI bridge to [bus 01-01]
[ 0.204853] pci 0000:00:08.0: bridge window [io 0x9000-0xafff]
[ 0.204905] pci 0000:00:08.0: bridge window [mem 0xdc000000-0xddffffff]
[ 0.204955] pci 0000:00:08.0: bridge window [mem 0xd8000000-0xd8ffffff pref]
[ 0.205020] pci 0000:03:00.0: BAR 6: assigned [mem 0xda000000-0xda01ffff pref]
[ 0.205076] pci 0000:00:1e.0: PCI bridge to [bus 03-03]
[ 0.205124] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff]
[ 0.205174] pci 0000:00:1e.0: bridge window [mem 0xda000000-0xdbffffff]
[ 0.205224] pci 0000:00:1e.0: bridge window [mem 0xc8000000-0xd7ffffff pref]
[ 0.205295] pci 0000:00:08.0: setting latency timer to 64
[ 0.205305] pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
[ 0.205309] pci_bus 0000:00: resource 1 [mem 0x00000000-0x3ffffffff]
[ 0.205314] pci_bus 0000:01: resource 0 [io 0x9000-0xafff]
[ 0.205317] pci_bus 0000:01: resource 1 [mem 0xdc000000-0xddffffff]
[ 0.205321] pci_bus 0000:01: resource 2 [mem 0xd8000000-0xd8ffffff pref]
[ 0.205325] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
[ 0.205329] pci_bus 0000:03: resource 1 [mem 0xda000000-0xdbffffff]
[ 0.205333] pci_bus 0000:03: resource 2 [mem 0xc8000000-0xd7ffffff pref]
[ 0.205422] NET: Registered protocol family 2
[ 0.205608] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.206236] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.207933] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.207933] Switched to NOHz mode on CPU #0
[ 0.208337] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.208388] TCP reno registered
[ 0.208437] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.208507] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.208867] NET: Registered protocol family 1
[ 0.264094] pci 0000:03:00.0: Boot video device
[ 0.264102] PCI: CLS 32 bytes, default 32
[ 0.264185] Unpacking initramfs...
[ 0.693484] Freeing initrd memory: 10868k freed
[ 0.709277] audit: initializing netlink socket (disabled)
[ 0.709349] type=2000 audit(1307389760.708:1): initialized
[ 0.733393] highmem bounce pool size: 64 pages
[ 0.733447] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.734031] VFS: Disk quotas dquot_6.5.2
[ 0.734187] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.734392] msgmni has been set to 1731
[ 0.734709] alg: No test for stdrng (krng)
[ 0.734799] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.734858] io scheduler noop registered
[ 0.734903] io scheduler deadline registered
[ 0.734958] io scheduler cfq registered (default)
[ 0.735347] ERST: Table is not found!
[ 0.735409] isapnp: Scanning for PnP cards...
[ 1.089736] isapnp: No Plug & Play device found
[ 1.089918] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.110411] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.130909] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.151692] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.172239] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.172619] Linux agpgart interface v0.103
[ 1.172805] agpgart: Detected NVIDIA nForce2 chipset
[ 1.182301] agpgart-nvidia 0000:00:00.0: AGP aperture is 128M @ 0xc0000000
[ 1.182578] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.182628] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.183534] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.183744] mousedev: PS/2 mouse device common for all mice
[ 1.183871] rtc_cmos 00:06: RTC can wake from S4
[ 1.184068] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.184143] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 1.184206] cpuidle: using governor ladder
[ 1.184251] cpuidle: using governor menu
[ 1.184733] TCP cubic registered
[ 1.184811] NET: Registered protocol family 10
[ 1.185914] Mobile IPv6
[ 1.185959] NET: Registered protocol family 17
[ 1.186009] Registering the dns_resolver key type
[ 1.186090] Using IPI No-Shortcut mode
[ 1.186280] PM: Hibernation image not present or could not be loaded.
[ 1.186297] registered taskstats version 1
[ 1.186995] rtc_cmos 00:06: setting system clock to 2011-06-06 19:49:22 UTC (1307389762)
[ 1.187088] Initializing network drop monitor service
[ 1.187289] Freeing unused kernel memory: 436k freed
[ 1.187919] Write protecting the kernel text: 2788k
[ 1.188000] Write protecting the kernel read-only data: 1028k
[ 1.208909] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.312296] udevd[46]: starting version 170
[ 1.419850] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 1.496289] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
[ 1.496364] forcedeth 0000:00:04.0: PCI INT A -> Link[APCH] -> GSI 22 (level, high) -> IRQ 22
[ 1.496428] forcedeth 0000:00:04.0: setting latency timer to 64
[ 1.701757] ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
[ 1.701829] skge 0000:01:04.0: PCI INT A -> Link[APC2] -> GSI 17 (level, high) -> IRQ 17
[ 1.701951] skge: 1.13 addr 0xdd000000 irq 17 chip Yukon-Lite rev 7
[ 1.702950] skge 0000:01:04.0: eth0: addr 00:11:2f:58:46:07
[ 1.721455] 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 1.721553] 8139cp 0000:01:08.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 1.732110] Refined TSC clocksource calibration: 1746.820 MHz.
[ 1.732171] Switching to clocksource tsc
[ 1.734344] usbcore: registered new interface driver usbfs
[ 1.734442] usbcore: registered new interface driver hub
[ 1.736109] usbcore: registered new device driver usb
[ 1.763038] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.765507] 8139too: 8139too Fast Ethernet driver 0.9.28
[ 1.765790] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 1.765855] 8139too 0000:01:08.0: PCI INT A -> Link[APC3] -> GSI 18 (level, high) -> IRQ 18
[ 1.767377] 8139too 0000:01:08.0: eth1: RealTek RTL8139 at 0x9400, 00:48:54:1b:a9:85, IRQ 18
[ 1.812523] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.824585] SCSI subsystem initialized
[ 1.874698] libata version 3.00 loaded.
[ 1.884255] sata_sil 0000:01:0b.0: version 2.4
[ 1.884343] sata_sil 0000:01:0b.0: PCI INT A -> Link[APC3] -> GSI 18 (level, high) -> IRQ 18
[ 1.885123] scsi0 : sata_sil
[ 1.885388] scsi1 : sata_sil
[ 1.885501] ata1: SATA max UDMA/100 mmio m512@0xdd005000 tf 0xdd005080 irq 18
[ 1.885553] ata2: SATA max UDMA/100 mmio m512@0xdd005000 tf 0xdd0050c0 irq 18
[ 2.020510] forcedeth 0000:00:04.0: eth2: Features changed: 0x00004800 -> 0x00004000
[ 2.021429] forcedeth 0000:00:04.0: ifname eth2, PHY OUI 0x732 @ 1, addr 00:11:2f:58:35:d2
[ 2.021489] forcedeth 0000:00:04.0: timirq lnktim desc-v1
[ 2.021992] ACPI: PCI Interrupt Link [APCM] enabled at IRQ 21
[ 2.022056] firewire_ohci 0000:00:0d.0: PCI INT A -> Link[APCM] -> GSI 21 (level, high) -> IRQ 21
[ 2.022119] firewire_ohci 0000:00:0d.0: setting latency timer to 64
[ 2.076098] firewire_ohci: Added fw-ohci device 0000:00:0d.0, OHCI v1.10, 4 IR + 4 IT contexts, quirks 0x0
[ 2.076461] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
[ 2.076523] ehci_hcd 0000:00:02.2: PCI INT C -> Link[APCL] -> GSI 20 (level, high) -> IRQ 20
[ 2.076616] ehci_hcd 0000:00:02.2: setting latency timer to 64
[ 2.076621] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 2.076728] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 2.076831] ehci_hcd 0000:00:02.2: debug port 1
[ 2.076884] ehci_hcd 0000:00:02.2: cache line size of 32 is not supported
[ 2.076904] ehci_hcd 0000:00:02.2: irq 20, io mem 0xde082000
[ 2.088029] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
[ 2.088136] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.088186] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.088242] usb usb1: Product: EHCI Host Controller
[ 2.088288] usb usb1: Manufacturer: Linux 2.6.39-1-686-pae ehci_hcd
[ 2.088336] usb usb1: SerialNumber: 0000:00:02.2
[ 2.088596] hub 1-0:1.0: USB hub found
[ 2.088649] hub 1-0:1.0: 6 ports detected
[ 2.089046] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 22
[ 2.089102] ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 22 (level, high) -> IRQ 22
[ 2.089193] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 2.089198] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 2.089266] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 2.089369] ohci_hcd 0000:00:02.0: irq 22, io mem 0xde086000
[ 2.146037] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.146092] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.146148] usb usb2: Product: OHCI Host Controller
[ 2.146194] usb usb2: Manufacturer: Linux 2.6.39-1-686-pae ohci_hcd
[ 2.146242] usb usb2: SerialNumber: 0000:00:02.0
[ 2.146608] hub 2-0:1.0: USB hub found
[ 2.150050] hub 2-0:1.0: 3 ports detected
[ 2.150211] pata_amd 0000:00:09.0: version 0.4.1
[ 2.150307] pata_amd 0000:00:09.0: setting latency timer to 64
[ 2.150997] scsi2 : pata_amd
[ 2.151206] scsi3 : pata_amd
[ 2.151915] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[ 2.151966] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[ 2.152529] ACPI: PCI Interrupt Link [APCG] enabled at IRQ 21
[ 2.152587] ohci_hcd 0000:00:02.1: PCI INT B -> Link[APCG] -> GSI 21 (level, high) -> IRQ 21
[ 2.152681] ohci_hcd 0000:00:02.1: setting latency timer to 64
[ 2.152686] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 2.152751] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[ 2.152843] ohci_hcd 0000:00:02.1: irq 21, io mem 0xde081000
[ 2.204047] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.210033] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.210083] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.210140] usb usb3: Product: OHCI Host Controller
[ 2.210187] usb usb3: Manufacturer: Linux 2.6.39-1-686-pae ohci_hcd
[ 2.210234] usb usb3: SerialNumber: 0000:00:02.1
[ 2.210697] hub 3-0:1.0: USB hub found
[ 2.210752] hub 3-0:1.0: 3 ports detected
[ 2.220535] ata1.00: ATA-6: HDS722516VLSA80, V34OA63A, max UDMA/100
[ 2.220590] ata1.00: 321672960 sectors, multi 16: LBA48
[ 2.244515] ata1.00: configured for UDMA/100
[ 2.244796] scsi 0:0:0:0: Direct-Access ATA HDS722516VLSA80 V34O PQ: 0 ANSI: 5
[ 2.324379] ata3.00: ATAPI: TSSTcorpCD/DVDW TS-H542A, TS01, max UDMA/33
[ 2.324441] ata3.01: ATAPI: IOMEGA ZIP 100 ATAPI, 13.A, max PIO2, CDB intr
[ 2.324507] ata3: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0000000) ACPI=0x701f (60:600:0x13)
[ 2.324514] ata3: nv_mode_filter: 0x7&0xfff9f->0x7, BIOS=0x0 (0xc0000000) ACPI=0x1 (60:600:0x13)
[ 2.340296] ata3.00: configured for UDMA/33
[ 2.356301] ata3.01: configured for PIO2
[ 2.456025] usb 1-5: new high speed USB device number 3 using ehci_hcd
[ 2.564041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 2.572242] ata2.00: ATAPI: HL-DT-ST DVDRAM GH22NS40, NL00, max UDMA/100
[ 2.576181] firewire_core: created device fw0: GUID 00e01800008e3614, S400
[ 2.588271] ata2.00: configured for UDMA/100
[ 2.590709] usb 1-5: New USB device found, idVendor=058f, idProduct=6362
[ 2.590760] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.590809] usb 1-5: Product: Mass Storage Device
[ 2.590855] usb 1-5: Manufacturer: Generic
[ 2.590901] usb 1-5: SerialNumber: 058F312D81B
[ 2.594468] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GH22NS40 NL00 PQ: 0 ANSI: 5
[ 2.596386] scsi 2:0:0:0: CD-ROM TSSTcorp CD/DVDW TS-H542A TS01 PQ: 0 ANSI: 5
[ 2.601076] scsi 2:0:1:0: Direct-Access IOMEGA ZIP 100 13.A PQ: 0 ANSI: 5
[ 2.843684] sd 0:0:0:0: [sda] 321672960 512-byte logical blocks: (164 GB/153 GiB)
[ 2.843823] sd 0:0:0:0: [sda] Write Protect is off
[ 2.843872] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.843965] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.844841] sda: detected capacity change from 0 to 164696555520
[ 2.847580] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.847648] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.848526] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.848790] usbcore: registered new interface driver uas
[ 2.850852] sr1: scsi3-mmc drive: 0x/40x writer cd/rw xa/form2 cdda tray
[ 2.851174] sr 2:0:0:0: Attached scsi CD-ROM sr1
[ 2.857156] sd 2:0:1:0: [sdb] Attached SCSI removable disk
[ 2.864892] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.865239] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.866163] sr 2:0:0:0: Attached scsi generic sg2 type 5
[ 2.866406] sd 2:0:1:0: Attached scsi generic sg3 type 0
[ 2.876082] usb 2-2: new low speed USB device number 2 using ohci_hcd
[ 2.927217] sda: sda1 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
[ 2.928562] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.956255] Initializing USB Mass Storage driver...
[ 2.958213] scsi4 : usb-storage 1-5:1.0
[ 2.962344] usbcore: registered new interface driver usb-storage
[ 2.962399] USB Mass Storage support registered.
[ 3.088894] usb 2-2: New USB device found, idVendor=046d, idProduct=c05a
[ 3.088973] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.089023] usb 2-2: Product: USB Optical Mouse
[ 3.089069] usb 2-2: Manufacturer: Logitech
[ 3.121516] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-2/2-2:1.0/input/input1
[ 3.121843] generic-usb 0003:046D:C05A.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:02.0-2/input0
[ 3.122272] usbcore: registered new interface driver usbhid
[ 3.122321] usbhid: USB HID core driver
[ 3.648632] [drm] Initialized drm 1.1.0 20060810
[ 3.721369] [drm] radeon kernel modesetting enabled.
[ 3.721698] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 3.721763] radeon 0000:03:00.0: PCI INT A -> Link[APC4] -> GSI 19 (level, high) -> IRQ 19
[ 3.723384] [drm] initializing kernel modesetting (RV280 0x1002:0x5960).
[ 3.723487] [drm] register mmio base: 0xDB000000
[ 3.723533] [drm] register mmio size: 65536
[ 3.725332] agpgart-nvidia 0000:00:00.0: AGP 3.0 bridge
[ 3.725400] agpgart-nvidia 0000:00:00.0: putting AGP V3 device into 8x mode
[ 3.725546] radeon 0000:03:00.0: putting AGP V3 device into 8x mode
[ 3.725601] radeon 0000:03:00.0: GTT: 128M 0xC0000000 - 0xC7FFFFFF
[ 3.725652] [drm] Generation 2 PCI interface, using max accessible memory
[ 3.725704] radeon 0000:03:00.0: VRAM: 128M 0x00000000C8000000 - 0x00000000CFFFFFFF (128M used)
[ 3.725772] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 3.725820] [drm] Driver supports precise vblank timestamp query.
[ 3.725903] [drm] radeon: irq initialized.
[ 3.726061] [drm] Detected VRAM RAM=128M, BAR=128M
[ 3.726117] [drm] RAM width 64bits DDR
[ 3.726284] [TTM] Zone kernel: Available graphics memory: 443368 kiB.
[ 3.726334] [TTM] Zone highmem: Available graphics memory: 774092 kiB.
[ 3.726382] [TTM] Initializing pool allocator.
[ 3.726479] [drm] radeon: 128M of VRAM memory ready
[ 3.726526] [drm] radeon: 128M of GTT memory ready.
[ 3.727878] radeon 0000:03:00.0: WB disabled
[ 3.728859] [drm] Loading R200 Microcode
[ 3.737626] [drm] radeon: ring at 0x00000000C0001000
[ 3.737698] [drm] ring test succeeded in 0 usecs
[ 3.738107] [drm] radeon: ib pool ready.
[ 3.738249] [drm] ib test succeeded in 0 usecs
[ 3.738677] [drm] Radeon Display Connectors
[ 3.738723] [drm] Connector 0:
[ 3.738766] [drm] VGA
[ 3.738810] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 3.738857] [drm] Encoders:
[ 3.738901] [drm] CRT1: INTERNAL_DAC1
[ 3.738945] [drm] Connector 1:
[ 3.738988] [drm] DVI-I
[ 3.739031] [drm] HPD1
[ 3.739075] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 3.739121] [drm] Encoders:
[ 3.739164] [drm] CRT2: INTERNAL_DAC2
[ 3.739209] [drm] DFP1: INTERNAL_TMDS1
[ 3.739253] [drm] Connector 2:
[ 3.739296] [drm] S-video
[ 3.739338] [drm] Encoders:
[ 3.739381] [drm] TV1: INTERNAL_DAC2
[ 3.988791] scsi 4:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 3.988904] [drm] fb mappable at 0xC8040000
[ 3.988950] [drm] vram apper at 0xC8000000
[ 3.988995] [drm] size 5242880
[ 3.989038] [drm] fb depth is 24
[ 3.989082] [drm] pitch is 5120
[ 3.990056] fbcon: radeondrmfb (fb0) is primary device
[ 4.116699] Console: switching to colour frame buffer device 160x64
[ 4.139843] fb0: radeondrmfb frame buffer device
[ 4.139963] drm: registered panic notifier
[ 4.140087] [drm] Initialized radeon 2.9.0 20080528 for 0000:03:00.0 on minor 0
[ 4.141703] scsi 4:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 4.142821] scsi 4:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 4.143678] scsi 4:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 4.144658] sd 4:0:0:0: Attached scsi generic sg4 type 0
[ 4.145021] sd 4:0:0:1: Attached scsi generic sg5 type 0
[ 4.145365] sd 4:0:0:2: Attached scsi generic sg6 type 0
[ 4.145709] sd 4:0:0:3: Attached scsi generic sg7 type 0
[ 4.157787] sd 4:0:0:1: [sdd] Attached SCSI removable disk
[ 4.159408] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[ 4.160294] sd 4:0:0:2: [sde] Attached SCSI removable disk
[ 4.161150] sd 4:0:0:3: [sdf] Attached SCSI removable disk
[ 4.229791] device-mapper: uevent: version 1.0.3
[ 4.230822] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 4.402012] PM: Starting manual resume from disk
[ 4.402151] PM: Hibernation image partition 8:1 present
[ 4.402154] PM: Looking for hibernation image.
[ 4.402433] PM: Image not found (code -22)
[ 4.402437] PM: Hibernation image not present or could not be loaded.
[ 4.409874] PM: Marking nosave pages: 000000000009f000 - 0000000000100000
[ 4.409883] PM: Basic memory bitmaps created
[ 4.421136] PM: Basic memory bitmaps freed
[ 4.471947] EXT3-fs: barriers not enabled
[ 4.489633] kjournald starting. Commit interval 5 seconds
[ 4.489806] EXT3-fs (sda8): mounted filesystem with ordered data mode
[ 6.070745] udevd[366]: starting version 170
[ 12.475592] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 12.566142] ACPI: acpi_idle registered with cpuidle
[ 12.599792] parport_pc 00:0b: reported by Plug and Play ACPI
[ 12.645880] ACPI: Power Button [PWRB]
[ 12.720405] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
[ 12.765285] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 12.782699] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 12.855206] ACPI: Power Button [PWRF]
[ 12.874325] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 12.890229] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 12.928684] udevd[388]: renamed network interface eth2 to eth5
[ 13.001218] i2c i2c-5: nForce2 SMBus adapter at 0x5000
[ 13.023260] udevd[396]: renamed network interface eth0 to rename2
[ 13.043405] udevd[406]: renamed network interface eth1 to eth2
[ 13.099469] Linux media interface: v0.10
[ 13.151124] parport0: Printer, HEWLETT-PACKARD DESKJET 710C
[ 13.283765] i2c i2c-6: nForce2 SMBus adapter at 0x5500
[ 13.376330] udevd[396]: renamed network interface rename2 to eth1
[ 13.489340] gameport gameport0: NS558 PnP Gameport is pnp00:0e/gameport0, io 0x201, speed 59659kHz
[ 13.649674] Linux video capture interface: v2.00
[ 13.913884] IR NEC protocol handler initialized
[ 14.104386] bttv: driver version 0.9.18 loaded
[ 14.117740] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 14.152650] IR RC5(x) protocol handler initialized
[ 14.166229] bttv: Bt8xx card found (0).
[ 14.267515] bttv 0000:01:07.0: PCI INT A -> Link[APC4] -> GSI 19 (level, high) -> IRQ 19
[ 14.312106] IR RC6 protocol handler initialized
[ 14.377770] bttv0: Bt878 (rev 17) at 0000:01:07.0, irq: 19, latency: 32, mmio: 0xd8000000
[ 14.416068] bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is 11bd:0012
[ 14.428683] bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected]
[ 14.498070] IR JVC protocol handler initialized
[ 14.516546] bttv0: gpio: en=00000000, out=00000000 in=00ff27ff [init]
[ 14.516810] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 14.543808] bttv0: miro: id=9 tuner=3 radio=no stereo=no
[ 14.555820] bttv0: tuner type=3
[ 14.657589] IR Sony protocol handler initialized
[ 14.708188] i2c-core: driver [msp3400] using legacy suspend method
[ 14.719877] i2c-core: driver [msp3400] using legacy resume method
[ 14.823556] lirc_dev: IR Remote Control driver registered, major 249
[ 14.909639] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
[ 14.920956] Intel ICH 0000:00:06.0: PCI INT A -> Link[APCJ] -> GSI 20 (level, high) -> IRQ 20
[ 14.979563] IR LIRC bridge handler initialized
[ 15.023229] Intel ICH 0000:00:06.0: setting latency timer to 64
[ 15.042496] bttv0: audio absent, no audio device found!
[ 15.235311] i2c-core: driver [tuner] using legacy suspend method
[ 15.246277] i2c-core: driver [tuner] using legacy resume method
[ 15.329785] All bytes are equal. It is not a TEA5767
[ 15.340374] tuner 7-0060: Tuner -1 found with type(s) Radio TV.
[ 15.351112] intel8x0_measure_ac97_clock: measured 58146 usecs (2816 samples)
[ 15.361478] intel8x0: clocking to 48000
[ 15.465700] tuner-simple 7-0060: creating new instance
[ 15.475848] tuner-simple 7-0060: type set to 3 (Philips (SECAM+PAL_BG) (FI1216MF, FM1216MF, FR1216MF))
[ 15.492233] bttv0: registered device video0
[ 15.502227] bttv0: registered device vbi0
[ 15.512052] bttv0: PLL: 28636363 => 35468950 .. ok
[ 15.560029] Bt87x 0000:01:07.1: PCI INT A -> Link[APC4] -> GSI 19 (level, high) -> IRQ 19
[ 15.579179] bt87x0: Using board 1, analog, digital (rate 32000 Hz)
[ 15.590281] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 15.632374] C-Media PCI 0000:01:0a.0: PCI INT A -> Link[APC1] -> GSI 16 (level, high) -> IRQ 16
[ 17.535958] Adding 610400k swap on /dev/sda10. Priority:-1 extents:1 across:610400k
[ 17.872997] EXT3-fs (sda8): using internal journal
[ 18.188111] lp0: using parport0 (interrupt-driven).
[ 18.279008] Uniform Multi-Platform E-IDE driver
[ 18.296632] ide-cd driver 5.00
[ 18.337956] ide-gd driver 1.18
[ 18.373499] ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
[ 21.383595] EXT3-fs: barriers not enabled
[ 21.412405] kjournald starting. Commit interval 5 seconds
[ 21.419643] EXT3-fs (sda1): warning: maximal mount count reached, running e2fsck is recommended
[ 21.427724] EXT3-fs (sda1): using internal journal
[ 21.434309] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 21.520251] EXT3-fs: barriers not enabled
[ 21.535934] kjournald starting. Commit interval 5 seconds
[ 21.542584] EXT3-fs (dm-3): warning: maximal mount count reached, running e2fsck is recommended
[ 21.549683] EXT3-fs (dm-3): using internal journal
[ 21.556521] EXT3-fs (dm-3): mounted filesystem with ordered data mode
[ 21.582276] EXT3-fs: barriers not enabled
[ 21.596539] kjournald starting. Commit interval 5 seconds
[ 21.603552] EXT3-fs (dm-1): using internal journal
[ 21.610186] EXT3-fs (dm-1): mounted filesystem with ordered data mode
[ 21.632834] EXT3-fs: barriers not enabled
[ 21.639925] kjournald starting. Commit interval 5 seconds
[ 21.646925] EXT3-fs (dm-2): using internal journal
[ 21.653608] EXT3-fs (dm-2): mounted filesystem with ordered data mode
[ 21.896168] EXT3-fs: barriers not enabled
[ 21.913574] kjournald starting. Commit interval 5 seconds
[ 21.922230] EXT3-fs (dm-0): using internal journal
[ 21.928978] EXT3-fs (dm-0): mounted filesystem with ordered data mode
[ 21.960743] EXT3-fs: barriers not enabled
[ 21.984823] kjournald starting. Commit interval 5 seconds
[ 21.985245] EXT3-fs (dm-4): using internal journal
[ 21.985253] EXT3-fs (dm-4): mounted filesystem with ordered data mode
[ 24.819127] RPC: Registered udp transport module.
[ 24.833608] RPC: Registered tcp transport module.
[ 24.840709] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 24.928277] FS-Cache: Loaded
[ 24.997482] FS-Cache: Netfs 'nfs' registered for caching
[ 25.031788] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 26.930230] fuse init (API version 7.16)
[ 27.229055] ttyS0: LSR safety check engaged!
[ 27.231283] ttyS0: LSR safety check engaged!
[ 27.241200] ttyS2: LSR safety check engaged!
[ 27.242997] ttyS2: LSR safety check engaged!
[ 27.245358] ttyS3: LSR safety check engaged!
[ 27.247142] ttyS3: LSR safety check engaged!
[ 27.555067] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 29.179601] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 29.222186] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[ 29.750627] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 29.752824] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 29.753027] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 29.941841] xt_time: kernel timezone is +0200
[ 30.669213] u32 classifier
[ 30.669300] Performance counters on
[ 30.669401] input device check on
[ 30.669495] Actions configured
[ 36.565681] forcedeth 0000:00:04.0: eth5: no link during initialization
[ 36.566596] ADDRCONF(NETDEV_UP): eth5: link is not ready
[ 36.610494] skge 0000:01:04.0: eth1: enabling interface
[ 36.650763] 8139too 0000:01:08.0: eth2: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 38.485642] Bluetooth: Core ver 2.16
[ 38.485808] NET: Registered protocol family 31
[ 38.485925] Bluetooth: HCI device and connection manager initialized
[ 38.486095] Bluetooth: HCI socket layer initialized
[ 38.486223] Bluetooth: L2CAP socket layer initialized
[ 38.486952] Bluetooth: SCO socket layer initialized
[ 38.500908] Bluetooth: RFCOMM TTY layer initialized
[ 38.501059] Bluetooth: RFCOMM socket layer initialized
[ 38.501196] Bluetooth: RFCOMM ver 1.11
[ 38.748858] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 38.749016] Bluetooth: BNEP filters: protocol multicast
[ 39.298771] ppdev: user-space parallel port driver
[ 47.520019] eth1: no IPv6 routers present
[ 52.856202] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 52.878762] NFSD: starting 90-second grace period
[ 99.172637] PM: Syncing filesystems ... done.
[ 99.201834] PM: Preparing system for mem sleep
[ 99.228873] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 99.244116] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 99.260097] PM: Entering mem sleep
[ 99.260133] Suspending console(s) (use no_console_suspend to debug)
[ 99.260964] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 99.264568] ns558 00:0e: disabled
[ 99.264638] mpu401 00:0d: disabled
[ 99.264718] parport_pc 00:0b: disabled
[ 99.264782] serial 00:0a: disabled
[ 99.264844] serial 00:09: disabled
[ 99.264853] serial 00:09: wake-up capability disabled by ACPI
[ 99.275463] C-Media PCI 0000:01:0a.0: PCI INT A disabled
[ 99.275498] ACPI handle has no context!
[ 99.275594] Bt87x 0000:01:07.1: PCI INT A disabled
[ 99.275650] ACPI handle has no context!
[ 99.275686] skge 0000:01:04.0: eth1: disabling interface
[ 99.279057] Intel ICH 0000:00:06.0: PCI INT A disabled
[ 99.281291] radeon 0000:03:00.0: PCI INT A disabled
[ 99.281320] ohci_hcd 0000:00:02.1: PCI INT B disabled
[ 99.281335] ohci_hcd 0000:00:02.0: PCI INT A disabled
[ 99.292032] ehci_hcd 0000:00:02.2: PCI INT C disabled
[ 99.362781] sd 0:0:0:0: [sda] Stopping disk
[ 99.833851] sata_sil 0000:01:0b.0: PCI INT A disabled
[ 99.848038] PM: suspend of devices complete after 587.382 msecs
[ 99.848646] skge 0000:01:04.0: PME# enabled
[ 99.848669] pci 0000:00:08.0: wake-up capability enabled by ACPI
[ 99.928119] PM: late suspend of devices complete after 80.074 msecs
[ 99.928193] ACPI: Preparing to enter system sleep state S3
[ 100.175340] PM: Saving platform NVS memory
[ 100.175445] Disabling non-boot CPUs ...
[ 100.175445] ACPI: Low-level resume complete
[ 100.175445] PM: Restoring platform NVS memory
[ 100.176550] ACPI: Waking up from system sleep state S3
[ 100.176789] agpgart-nvidia 0000:00:00.0: restoring config space at offset 0x4 (was 0x8, writing 0xc0000008)
[ 100.176836] pci 0000:00:00.4: restoring config space at offset 0xf (was 0x0, writing 0xff)
[ 100.176850] pci 0000:00:00.5: restoring config space at offset 0xf (was 0x0, writing 0xff)
[ 100.176895] nForce2_smbus 0000:00:01.1: restoring config space at offset 0xf (was 0x1030100, writing 0x1030109)
[ 100.176909] nForce2_smbus 0000:00:01.1: restoring config space at offset 0x4 (was 0x1, writing 0xdc01)
[ 100.176941] ohci_hcd 0000:00:02.0: restoring config space at offset 0x1 (was 0xb00002, writing 0xb00003)
[ 100.176973] ohci_hcd 0000:00:02.1: restoring config space at offset 0x1 (was 0xb00002, writing 0xb00003)
[ 100.192024] forcedeth 0000:00:04.0: BAR 0: set to [mem 0xde083000-0xde083fff] (PCI address [0xde083000-0xde083fff])
[ 100.192032] forcedeth 0000:00:04.0: BAR 1: set to [io 0xe000-0xe007] (PCI address [0xe000-0xe007])
[ 100.192042] forcedeth 0000:00:04.0: restoring config space at offset 0xf (was 0x14010100, writing 0x14010109)
[ 100.192058] forcedeth 0000:00:04.0: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00007)
[ 100.192130] pci 0000:00:08.0: restoring config space at offset 0x7 (was 0x2280a090, writing 0xb280a090)
[ 100.208016] pata_amd 0000:00:09.0: BAR 4: set to [io 0xf000-0xf00f] (PCI address [0xf000-0xf00f])
[ 100.208037] pata_amd 0000:00:09.0: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00005)
[ 100.224015] firewire_ohci 0000:00:0d.0: BAR 0: set to [mem 0xde084000-0xde0847ff] (PCI address [0xde084000-0xde0847ff])
[ 100.224022] firewire_ohci 0000:00:0d.0: BAR 1: set to [mem 0xde085000-0xde08503f] (PCI address [0xde085000-0xde08503f])
[ 100.224032] firewire_ohci 0000:00:0d.0: restoring config space at offset 0xf (was 0x1030100, writing 0x1030109)
[ 100.224048] firewire_ohci 0000:00:0d.0: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00007)
[ 100.224070] pci 0000:00:1e.0: restoring config space at offset 0x7 (was 0x220c0c0, writing 0x2220c0c0)
[ 100.224093] skge 0000:01:04.0: restoring config space at offset 0xf (was 0x1f170100, writing 0x1f170105)
[ 100.224111] skge 0000:01:04.0: restoring config space at offset 0x5 (was 0x1, writing 0x9001)
[ 100.224117] skge 0000:01:04.0: restoring config space at offset 0x4 (was 0x0, writing 0xdd000000)
[ 100.224124] skge 0000:01:04.0: restoring config space at offset 0x3 (was 0x0, writing 0x2008)
[ 100.224131] skge 0000:01:04.0: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00007)
[ 100.224157] bttv 0000:01:07.0: restoring config space at offset 0xf (was 0x28100100, writing 0x2810010b)
[ 100.224175] bttv 0000:01:07.0: restoring config space at offset 0x4 (was 0x8, writing 0xd8000008)
[ 100.224182] bttv 0000:01:07.0: restoring config space at offset 0x3 (was 0x800000, writing 0x802000)
[ 100.224189] bttv 0000:01:07.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900006)
[ 100.224215] Bt87x 0000:01:07.1: restoring config space at offset 0xf (was 0xff040100, writing 0xff04010b)
[ 100.224233] Bt87x 0000:01:07.1: restoring config space at offset 0x4 (was 0x8, writing 0xd8001008)
[ 100.224239] Bt87x 0000:01:07.1: restoring config space at offset 0x3 (was 0x800000, writing 0x802000)
[ 100.224247] Bt87x 0000:01:07.1: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002)
[ 100.224281] 8139too 0000:01:08.0: restoring config space at offset 0x5 (was 0x0, writing 0xdd004000)
[ 100.224288] 8139too 0000:01:08.0: restoring config space at offset 0x4 (was 0x1, writing 0x9401)
[ 100.224294] 8139too 0000:01:08.0: restoring config space at offset 0x3 (was 0x0, writing 0x2000)
[ 100.224302] 8139too 0000:01:08.0: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900007)
[ 100.224323] C-Media PCI 0000:01:0a.0: restoring config space at offset 0xf (was 0x180201ff, writing 0x18020109)
[ 100.224342] C-Media PCI 0000:01:0a.0: restoring config space at offset 0x4 (was 0xff01, writing 0x9801)
[ 100.224349] C-Media PCI 0000:01:0a.0: restoring config space at offset 0x3 (was 0x0, writing 0x2000)
[ 100.224357] C-Media PCI 0000:01:0a.0: restoring config space at offset 0x1 (was 0x2100080, writing 0x2100001)
[ 100.224378] sata_sil 0000:01:0b.0: restoring config space at offset 0xf (was 0x100, writing 0x10b)
[ 100.224390] sata_sil 0000:01:0b.0: restoring config space at offset 0x9 (was 0x0, writing 0xdd005000)
[ 100.224397] sata_sil 0000:01:0b.0: restoring config space at offset 0x8 (was 0x1, writing 0xac01)
[ 100.224404] sata_sil 0000:01:0b.0: restoring config space at offset 0x7 (was 0x1, writing 0xa801)
[ 100.224410] sata_sil 0000:01:0b.0: restoring config space at offset 0x6 (was 0x1, writing 0xa401)
[ 100.224417] sata_sil 0000:01:0b.0: restoring config space at offset 0x5 (was 0x1, writing 0xa001)
[ 100.224423] sata_sil 0000:01:0b.0: restoring config space at offset 0x4 (was 0x1, writing 0x9c01)
[ 100.224430] sata_sil 0000:01:0b.0: restoring config space at offset 0x3 (was 0x0, writing 0x2008)
[ 100.224437] sata_sil 0000:01:0b.0: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00007)
[ 100.224458] radeon 0000:03:00.0: restoring config space at offset 0xf (was 0x801ff, writing 0x8010b)
[ 100.224471] radeon 0000:03:00.0: restoring config space at offset 0x6 (was 0x0, writing 0xdb000000)
[ 100.224477] radeon 0000:03:00.0: restoring config space at offset 0x5 (was 0x1, writing 0xc001)
[ 100.224482] radeon 0000:03:00.0: restoring config space at offset 0x4 (was 0x8, writing 0xc8000008)
[ 100.224488] radeon 0000:03:00.0: restoring config space at offset 0x3 (was 0x800000, writing 0x802008)
[ 100.224495] radeon 0000:03:00.0: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00007)
[ 100.224521] pci 0000:03:00.1: restoring config space at offset 0x5 (was 0x0, writing 0xdb010000)
[ 100.224527] pci 0000:03:00.1: restoring config space at offset 0x4 (was 0x8, writing 0xd0000008)
[ 100.224533] pci 0000:03:00.1: restoring config space at offset 0x3 (was 0x0, writing 0x2008)
[ 100.224727] PM: early resume of devices complete after 47.991 msecs
[ 100.225180] agpgart-nvidia 0000:00:00.0: nForce2 C1 Halt Disconnect fixup
[ 100.225331] ohci_hcd 0000:00:02.0: PCI INT A -> Link[APCF] -> GSI 22 (level, high) -> IRQ 22
[ 100.225339] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 100.225363] ohci_hcd 0000:00:02.1: PCI INT B -> Link[APCG] -> GSI 21 (level, high) -> IRQ 21
[ 100.225370] ohci_hcd 0000:00:02.1: setting latency timer to 64
[ 100.225392] ehci_hcd 0000:00:02.2: PCI INT C -> Link[APCL] -> GSI 20 (level, high) -> IRQ 20
[ 100.225399] ehci_hcd 0000:00:02.2: setting latency timer to 64
[ 100.225748] Intel ICH 0000:00:06.0: PCI INT A -> Link[APCJ] -> GSI 20 (level, high) -> IRQ 20
[ 100.225755] Intel ICH 0000:00:06.0: setting latency timer to 64
[ 100.225787] pci 0000:00:08.0: setting latency timer to 64
[ 100.225803] pata_amd 0000:00:09.0: setting latency timer to 64
[ 100.225855] pci 0000:00:08.0: wake-up capability disabled by ACPI
[ 100.225863] skge 0000:01:04.0: PME# disabled
[ 100.225893] skge 0000:01:04.0: eth1: enabling interface
[ 100.230434] Bt87x 0000:01:07.1: PCI INT A -> Link[APC4] -> GSI 19 (level, high) -> IRQ 19
[ 100.230470] 8139too 0000:01:08.0: eth2: link down
[ 100.230517] C-Media PCI 0000:01:0a.0: PCI INT A -> Link[APC1] -> GSI 16 (level, high) -> IRQ 16
[ 100.230619] sata_sil 0000:01:0b.0: PCI INT A -> Link[APC3] -> GSI 18 (level, high) -> IRQ 18
[ 100.230654] radeon 0000:03:00.0: PCI INT A -> Link[APC4] -> GSI 19 (level, high) -> IRQ 19
[ 100.230666] [drm] AGP mode requested: 8
[ 100.230671] agpgart-nvidia 0000:00:00.0: AGP 3.0 bridge
[ 100.230693] agpgart-nvidia 0000:00:00.0: putting AGP V3 device into 8x mode
[ 100.230789] radeon 0000:03:00.0: putting AGP V3 device into 8x mode
[ 100.230800] radeon 0000:03:00.0: GTT: 128M 0xC0000000 - 0xC7FFFFFF
[ 100.254779] radeon 0000:03:00.0: WB disabled
[ 100.254821] [drm] radeon: ring at 0x00000000C0001000
[ 100.254841] [drm] ring test succeeded in 0 usecs
[ 100.254855] [drm] ib test succeeded in 0 usecs
[ 100.278918] serial 00:09: activated
[ 100.279310] serial 00:0a: activated
[ 100.279910] parport_pc 00:0b: activated
[ 100.280103] bttv0: reset, reinitialize
[ 100.280137] bttv0: PLL: 28636363 => 35468950 .
[ 100.280561] mpu401 00:0d: activated
[ 100.280887] ns558 00:0e: activated
[ 100.315960] .
[ 100.315982] sd 0:0:0:0: [sda] Starting disk
[ 100.366436] ok
[ 100.428876] firewire_core: skipped bus generations, destroying all nodes
[ 100.429234] ata3.01: ACPI cmd ef/03:20:00:00:00:b0 (SET FEATURES) filtered out
[ 100.429239] ata3.01: ACPI cmd ef/03:08:00:00:00:b0 (SET FEATURES) filtered out
[ 100.472645] 8139too 0000:01:08.0: eth2: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 100.508395] ata3.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out
[ 100.508401] ata3.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 100.508422] ata3: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0000000) ACPI=0x701f (60:600:0x13)
[ 100.508430] ata3: nv_mode_filter: 0x7&0xfff9f->0x7, BIOS=0x0 (0xc0000000) ACPI=0x1 (60:600:0x13)
[ 100.524567] ata3.00: configured for UDMA/33
[ 100.540311] ata3.01: configured for PIO2
[ 100.580022] usb 1-5: reset high speed USB device number 3 using ehci_hcd
[ 100.588043] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 100.612238] ata2.00: configured for UDMA/100
[ 100.749195] forcedeth 0000:00:04.0: eth5: no link during initialization
[ 100.928040] firewire_core: rediscovered device fw0
[ 104.284041] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 104.340510] ata1.00: configured for UDMA/100
[ 104.353585] PM: resume of devices complete after 4128.547 msecs
[ 104.494790] PM: Finishing wakeup.
[ 104.494794] Restarting tasks ... done.
 

Thread Tools




All times are GMT. The time now is 08:29 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright ©2007 - 2008, www.linux-archive.org