FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 03-10-2011, 04:54 AM
"David A. Parker"
 
Default Bug#617635: linux-image-2.6.32-5-amd64: Network connection drops under heavy load (tg3 driver)

Package: linux-2.6
Version: 2.6.32-30
Severity: important

I have an HP 6005 workstation with a clean install of Squeeze (64-bit) with the default kernel (2.6.32-5-amd64). The network connection drops periodically, but it comes back if you hit a key on the keyboard plugged into the machine.

Here's one method which I can use to consistently reproduce the problem:

1. I log into the machine via SSH
2. I attempt to transfer a file via SFTP
3. At some point during the file transfer, my SSH session will just hang and all connectivity to the machine is lost (I can't ping it, start a new SSH session, etc.)
4. If I walk over to the physical machine and hit any key on the keyboard, network connectivity immediately resumes, but it usually drops again a few seconds later and I have to hit a key again.

Once the file transfer completes, the network connection resumes working normally. This connection problem seems to happen any time I am doing something fairly network intensive (large file transfer, X11 forwarding, etc.). The connection is stable under a "normal" load (e.g., an SSH session or continuous ping). If I trigger this lock-up behavior and leave it in its "frozen" state for a few minutes, then the problem eventually gets corrected and some messages get logged regarding a CPU lockup condition (see kernel log messages starting at timestamp 442.826956, below).

Onboard NIC is a Broadcom NetXtreme BCM5761 using the tg3 driver.


-- Package-specific info:
** Version:
Linux version 2.6.32-5-amd64 (Debian 2.6.32-30) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Jan 12 03:40:32 UTC 2011

** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-amd64 root=UUID=bcb9d5b0-f613-4070-8730-893f5472bfd9 ro quiet

** Not tainted

** Kernel log:
[ 6.733608] usbhid: v2.6:USB HID core driver
[ 6.734876] sda1 sda2
[ 6.750371] sdb1
[ 6.750566] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 6.765522] sd 0:0:0:0: [sda] Attached SCSI disk
[ 6.771589] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 6.771591] Uniform CD-ROM driver Revision: 3.20
[ 6.771648] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 6.773777] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 6.773799] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 6.773819] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 7.202054] PM: Starting manual resume from disk
[ 7.202057] PM: Resume from partition 8:2
[ 7.202058] PM: Checking hibernation image.
[ 7.232039] PM: Error -22 checking image file
[ 7.232041] PM: Resume from disk failed.
[ 7.310294] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 8.629449] udev[413]: starting version 164
[ 9.210218] processor LNXCPU:00: registered as cooling_device0
[ 9.210328] processor LNXCPU:01: registered as cooling_device1
[ 9.210438] processor LNXCPU:02: registered as cooling_device2
[ 9.210507] processor LNXCPU:03: registered as cooling_device3
[ 9.228021] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 9.228039] ACPI: Power Button [PBTN]
[ 9.228078] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 9.228081] ACPI: Power Button [PWRF]
[ 9.362550] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 9.619156] ACPI: WMI: Mapper loaded
[ 9.638734] tpm_inf_pnp 00:09: Found TPM with ID IFX0102
[ 9.638814] tpm_inf_pnp 00:09: TPM found: config base 0x4e, data base 0x480, chip version 0x000b, vendor id 0x15d1 (Infineon), product id 0x000b (SLB 9635 TT 1.2)
[ 9.841486] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 9.887022] shpchp 0000:00:01.0: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0
[ 9.887025] shpchp 0000:00:01.0: Cannot reserve MMIO region
[ 9.887123] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.899070] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xfc00, revision 0
[ 9.919495] Error: Driver 'pcspkr' is already registered, aborting...
[ 9.954707] EDAC MC: Ver: 2.1.0 Jan 12 2011
[ 10.052408] [drm] Initialized drm 1.1.0 20060810
[ 10.058679] EDAC amd64_edac: Ver: 3.2.0 Jan 12 2011
[ 10.058748] EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3).
[ 10.058755] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
[ 10.058756] Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
[ 10.058757] (Note that use of the override may cause unknown side effects.)
[ 10.058771] amd64_edac: probe of 0000:00:18.2 failed with error -22
[ 10.112361] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.338240] [drm] radeon defaulting to userspace modesetting.
[ 10.338648] pci 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 10.338651] pci 0000:01:05.0: setting latency timer to 64
[ 10.338745] [drm] Initialized radeon 1.32.0 20080528 for 0000:01:05.0 on minor 0
[ 10.393679] hda_codec: ALC662 rev1: BIOS auto-probing.
[ 10.395157] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input5
[ 11.018474] Adding 23477240k swap on /dev/sda2. Priority:-1 extents:1 across:23477240k
[ 11.448266] loop: module loaded
[ 11.694024] EXT4-fs (sdb1): mounted filesystem with ordered data mode
[ 13.049943] alloc irq_desc for 26 on node 0
[ 13.049945] alloc kstat_irqs on node 0
[ 13.049956] tg3 0000:3f:00.0: irq 26 for MSI/MSI-X
[ 14.436987] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.972524] vboxdrv: Found 4 processor cores.
[ 14.972578] VBoxDrv: dbg - g_abExecMemory=ffffffffa041e580
[ 14.972625] vboxdrv: fAsync=0 offMin=0x370 offMax=0x7338
[ 14.972653] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 14.972654] vboxdrv: Successfully loaded version 4.0.4 (interface 0x00160000).
[ 16.767145] tg3: eth0: Link is up at 1000 Mbps, full duplex.
[ 16.767147] tg3: eth0: Flow control is off for TX and off for RX.
[ 16.768026] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.624080] eth0: no IPv6 routers present
[ 442.826956] Clocksource tsc unstable (delta = 299985606581 ns)
[ 442.828411] Switching to clocksource hpet
[ 442.829530] BUG: soft lockup - CPU#3 stuck for 279s! [ssh:1186]
[ 442.829566] Modules linked in: vboxnetadp vboxnetflt vboxdrv loop snd_hda_codec_realtek radeon ttm snd_hda_intel drm_kms_helper snd_hda_codec drm edac_core i2c_algo_bit snd_hwdep i2c_piix4 shpchp snd_pcm edac_mce_amd pci_hotplug i2c_core snd_timer psmouse snd soundcore tpm_infineon snd_page_alloc wmi tpm tpm_bios pcspkr evdev button processor serio_raw ext4 mbcache jbd2 crc16 sg sr_mod cdrom sd_mod crc_t10dif usbhid hid ahci ohci_hcd libata thermal thermal_sys ehci_hcd tg3 libphy usbcore nls_base scsi_mod [last unloaded: scsi_wait_scan]
[ 442.829593] CPU 3:
[ 442.829594] Modules linked in: vboxnetadp vboxnetflt vboxdrv loop snd_hda_codec_realtek radeon ttm snd_hda_intel drm_kms_helper snd_hda_codec drm edac_core i2c_algo_bit snd_hwdep i2c_piix4 shpchp snd_pcm edac_mce_amd pci_hotplug i2c_core snd_timer psmouse snd soundcore tpm_infineon snd_page_alloc wmi tpm tpm_bios pcspkr evdev button processor serio_raw ext4 mbcache jbd2 crc16 sg sr_mod cdrom sd_mod crc_t10dif usbhid hid ahci ohci_hcd libata thermal thermal_sys ehci_hcd tg3 libphy usbcore nls_base scsi_mod [last unloaded: scsi_wait_scan]
[ 442.829614] Pid: 1186, comm: ssh Not tainted 2.6.32-5-amd64 #1 HP Compaq 6005 Pro MT PC
[ 442.829616] RIP: 0010:[<ffffffff8119502d>] [<ffffffff8119502d>] copy_user_generic_string+0x2d/0x40
[ 442.829623] RSP: 0018:ffff88021cf89b80 EFLAGS: 00000246
[ 442.829624] RAX: ffff88021cf88000 RBX: 0000000000000370 RCX: 0000000000000001
[ 442.829626] RDX: 0000000000000000 RSI: ffff88021c4f6604 RDI: 00007fffc4241358
[ 442.829628] RBP: ffffffff8101166e R08: 00000000d7f8a216 R09: 0000000000000000
[ 442.829629] R10: 0000000000000000 R11: ffff88021d2f8d00 R12: ffff88021ccc0000
[ 442.829631] R13: 0000000000000000 R14: 00000000000000db R15: ffffffff810fc797
[ 442.829632] FS: 00007fa02829f720(0000) GS:ffff880008d80000(0000) knlGS:0000000000000000
[ 442.829634] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 442.829636] CR2: 00007fa028248000 CR3: 000000021d0f1000 CR4: 00000000000006e0
[ 442.829637] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 442.829639] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[ 442.829640] Call Trace:
[ 442.829644] [<ffffffff812495d0>] ? memcpy_toiovec+0x34/0x63
[ 442.829646] [<ffffffff81249edc>] ? skb_copy_datagram_iovec+0x7c/0x1ed
[ 442.829649] [<ffffffff8127e251>] ? tcp_recvmsg+0x6e5/0xa9e
[ 442.829653] [<ffffffff812425fa>] ? sock_common_recvmsg+0x30/0x45
[ 442.829656] [<ffffffff812405f8>] ? sock_aio_read+0xb9/0xc4
[ 442.829658] [<ffffffff81195030>] ? copy_user_generic_string+0x30/0x40
[ 442.829661] [<ffffffff810ee809>] ? do_sync_read+0xce/0x113
[ 442.829665] [<ffffffff8100f6c4>] ? __switch_to+0x1ad/0x297
[ 442.829668] [<ffffffff81064d2a>] ? autoremove_wake_function+0x0/0x2e
[ 442.829671] [<ffffffff81048079>] ? finish_task_switch+0x96/0xaf
[ 442.829673] [<ffffffff810ef265>] ? vfs_read+0xb9/0xff
[ 442.829675] [<ffffffff810ef367>] ? sys_read+0x45/0x6e
[ 442.829677] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b

** Model information
sys_vendor: Hewlett-Packard
product_name: HP Compaq 6005 Pro MT PC
product_version:
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 786G6 v01.11
board_vendor: Hewlett-Packard
board_name: 3047h
board_version:

** Loaded modules:
Module Size Used by
vboxnetadp 4625 0
vboxnetflt 15856 0
vboxdrv 1741122 2 vboxnetadp,vboxnetflt
loop 11799 0
snd_hda_codec_realtek 235602 1
radeon 573996 0
ttm 39986 1 radeon
snd_hda_intel 20019 0
drm_kms_helper 20065 1 radeon
snd_hda_codec 54244 2 snd_hda_codec_realtek,snd_hda_intel
drm 142359 3 radeon,ttm,drm_kms_helper
edac_core 29261 0
i2c_algo_bit 4225 1 radeon
snd_hwdep 5380 1 snd_hda_codec
i2c_piix4 8328 0
shpchp 26264 0
snd_pcm 60503 2 snd_hda_intel,snd_hda_codec
edac_mce_amd 6433 0
pci_hotplug 21203 1 shpchp
i2c_core 15712 5 radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_piix4
snd_timer 15582 1 snd_pcm
psmouse 49777 0
snd 46446 6 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec, snd_hwdep,snd_pcm,snd_timer
soundcore 4598 1 snd
tpm_infineon 7499 0
snd_page_alloc 6249 2 snd_hda_intel,snd_pcm
wmi 4323 0
tpm 9917 1 tpm_infineon
tpm_bios 4521 1 tpm
pcspkr 1699 0
evdev 7352 3
button 4650 0
processor 29935 0
serio_raw 3752 0
ext4 289033 2
mbcache 5050 1 ext4
jbd2 67015 1 ext4
crc16 1319 1 ext4
sg 18744 0
sr_mod 12602 0
cdrom 29415 1 sr_mod
sd_mod 29889 5
crc_t10dif 1276 1 sd_mod
usbhid 33292 0
hid 63225 1 usbhid
ahci 32374 3
ohci_hcd 19212 0
libata 133632 1 ahci
thermal 11674 0
thermal_sys 11942 2 processor,thermal
ehci_hcd 31151 0
tg3 95663 0
libphy 14054 1 tg3
usbcore 122034 4 usbhid,ohci_hcd,ehci_hcd
nls_base 6377 1 usbcore
scsi_mod 122149 4 sg,sr_mod,sd_mod,libata

** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
#allow-hotplug eth0
#iface eth0 inet dhcp

allow-hotplug eth0
iface eth0 inet static
address 10.3.1.65
netmask 255.255.248.0
network 10.3.0.0
broadcast 10.3.7.255
gateway 10.3.1.1

** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 64:31:50:3d:ba:f4 brd ff:ff:ff:ff:ff:ff
inet 10.3.1.65/21 brd 10.3.7.255 scope global eth0
inet6 fe80::6631:50ff:fe3d:baf4/64 scope link
valid_lft forever preferred_lft forever
3: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff

*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0:541609603 1050795 0 14424 0 4 0 4952 24654238 188101 0 0 0 0 0 0
vboxnet0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

*** Protocol statistics:
Ip:
359184 total packets received
0 forwarded
0 incoming packets discarded
359184 incoming packets delivered
188012 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
22254 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 22254
IcmpMsg:
OutType3: 22254
Tcp:
15 active connections openings
2 passive connection openings
0 failed connection attempts
0 connection resets received
1 connections established
331606 segments received
165727 segments send out
0 segments retransmited
0 bad segments received.
0 resets sent
Udp:
31 packets received
22261 packets to unknown port received.
0 packet receive errors
31 packets sent
UdpLite:
TcpExt:
8 TCP sockets finished time wait in fast timer
19 delayed acks sent
Quick ack mode was activated 4 times
5 packets directly queued to recvmsg prequeue.
1 bytes directly received in process context from prequeue
324431 packet headers predicted
149 acknowledgments not containing data payload received
21195 predicted acknowledgments
4 DSACKs sent for old packets
IpExt:
InMcastPkts: 195
InBcastPkts: 5091
InOctets: 467020152
OutOctets: 21263972
InMcastOctets: 5460
InBcastOctets: 616257

*** Device features:
eth0: 0x1909b3
lo: 0x13865
vboxnet0: 0x0

** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS880 Host Bridge [1022:9601]
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR+ <PERR- INTx-
Latency: 32
Capabilities: [c4] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=12 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency 0: [b]
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [54] HyperTransport: UnitID Clumping
Capabilities: [40] HyperTransport: Retry Mode
Capabilities: [9c] HyperTransport: #1a
Capabilities: [f8] HyperTransport: #1c

00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: f0000000-f01fffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [b0] Subsystem: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602]

00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) [1022:9609] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=3f, subordinate=3f, sec-latency=0
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #10, PowerLimit 35.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Not Supported, TimeoutDis- ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4159
Capabilities: [b0] Subsystem: Hewlett-Packard Company Device [103c:3047]
Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
Capabilities: [110 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Kernel driver in use: pcieport

00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (prog-if 01 [AHCI 1.0])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 2110 [size=8]
Region 1: I/O ports at 2120 [size=4]
Region 2: I/O ports at 2118 [size=8]
Region 3: I/O ports at 2124 [size=4]
Region 4: I/O ports at 2100 [size=16]
Region 5: Memory at f0309000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] SATA HBA v1.0 InCfgSpace
Kernel driver in use: ahci

00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0304000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0305000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at f0309400 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd

00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0306000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700 USB OHCI1 Controller [1002:4398] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f0307000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at f0309500 (32-bit, non-prefetchable) [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
Capabilities: [e4] Debug port: BAR=1 offset=00e0
Kernel driver in use: ehci_hcd

00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3c)
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [b0] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: piix4_smbus

00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia (Intel HDA) [1002:4383]
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at f0300000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: HDA Intel

00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=0f, subordinate=0f, sec-latency=64
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f0308000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration [1022:1200]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: [b]
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Address Map [1022:1201]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller [1022:1202]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control [1022:1203]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>

00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Family 10h Processor Link Control [1022:1204]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RS880 [Radeon HD 4200] [1002:9710] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
Region 1: I/O ports at 1100 [size=256]
Region 2: Memory at f0100000 (32-bit, non-prefetchable) [size=64K]
Region 5: Memory at f0000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000

3f:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5761 Gigabit Ethernet PCIe [14e4:1681] (rev 10)
Subsystem: Hewlett-Packard Company Device [103c:3047]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 26
Region 0: Memory at f0200000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at f0210000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [40] Vital Product Data
Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
Read-only fields:
[PN] Part number: BCM95761
[EC] Engineering changes: 106679-15
[SN] Serial number: 0123456789
[MN] Manufacture ID: 31 34 65 34
[RV] Reserved: checksum good, 28 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [60] Vendor Specific Information: Len=6c <?>
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4181
Capabilities: [cc] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [13c v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 64-31-50-ff-fe-3d-ba-f4
Capabilities: [16c v1] Power Budgeting <?>
Kernel driver in use: tg3


** USB devices:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 03f0:0024 Hewlett-Packard KU-0316 Keyboard
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: 6.0
APT prefers squeeze-updates
APT policy: (500, 'squeeze-updates'), (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.32-5-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-2.6.32-5-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-30 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.32-5-amd64 recommends:
pn firmware-linux-free <none> (no description available)

Versions of packages linux-image-2.6.32-5-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)

Versions of packages linux-image-2.6.32-5-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)

-- debconf information:
linux-image-2.6.32-5-amd64/postinst/ignoring-do-bootloader-2.6.32-5-amd64:
linux-image-2.6.32-5-amd64/postinst/depmod-error-initrd-2.6.32-5-amd64: false
linux-image-2.6.32-5-amd64/prerm/removing-running-kernel-2.6.32-5-amd64: true
linux-image-2.6.32-5-amd64/postinst/missing-firmware-2.6.32-5-amd64:



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110310055458.1975.49918.reportbug@ip-3-1-65.uc.utica.edu">http://lists.debian.org/20110310055458.1975.49918.reportbug@ip-3-1-65.uc.utica.edu
 
Old 03-10-2011, 01:26 PM
Ben Hutchings
 
Default Bug#617635: linux-image-2.6.32-5-amd64: Network connection drops under heavy load (tg3 driver)

On Thu, 2011-03-10 at 00:54 -0500, David A. Parker wrote:
> Package: linux-2.6
> Version: 2.6.32-30
> Severity: important
>
> I have an HP 6005 workstation with a clean install of Squeeze (64-bit)
> with the default kernel (2.6.32-5-amd64). The network connection drops
> periodically, but it comes back if you hit a key on the keyboard
> plugged into the machine.
[...]

Please test without the VirtualBox modules.

Ben.

--
Ben Hutchings
Once a job is fouled up, anything done to improve it makes it worse.
 
Old 03-10-2011, 03:28 PM
"David A. Parker"
 
Default Bug#617635: linux-image-2.6.32-5-amd64: Network connection drops under heavy load (tg3 driver)

This behavior persists without the VirtualBox modules loaded. The only
difference was that no messages were dumped to the logs this time after
the connection resumed.





--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 4D78FC4A.80303@utica.edu">http://lists.debian.org/4D78FC4A.80303@utica.edu
 

Thread Tools




All times are GMT. The time now is 03:51 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org