Linux Archive

Linux Archive (http://www.linux-archive.org/)
-   Debian Kernel (http://www.linux-archive.org/debian-kernel/)
-   -   Bug#617220: linux-image-2.6.32-5-xen-amd64: NETDEV WATCHDOG: pethx11 (r8169): transmit queue 0 timed out (http://www.linux-archive.org/debian-kernel/498157-bug-617220-linux-image-2-6-32-5-xen-amd64-netdev-watchdog-pethx11-r8169-transmit-queue-0-timed-out.html)

Sebastien Koechlin 03-07-2011 08:50 AM

Bug#617220: linux-image-2.6.32-5-xen-amd64: NETDEV WATCHDOG: pethx11 (r8169): transmit queue 0 timed out
 
Package: linux-2.6
Version: 2.6.32-30
Severity: normal

Got the following WARNING in dmesg:
[1062387.509572] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1062387.509575] EDD information not available.
[1093555.812090] ------------[ cut here ]------------
[1093555.812101] WARNING: at /build/buildd-linux-2.6_2.6.32-30-amd64-d4MbNM/linux-2.6-2.6.32/debian/build/source_amd64_xen/net/sched/sch_generic.c:261 dev_watchdog+0xe2/0x194()
[1093555.812106] Hardware name: PowerEdge T300
[1093555.812109] NETDEV WATCHDOG: pethx11 (r8169): transmit queue 0 timed out
[1093555.812112] Modules linked in: cpufreq_stats st ide_gd_mod ide_cd_mod ide_core ipt_REJECT xt_tcpudp xt_state xt_physdev xen_evtchn xenfs nfsd exportfs nfs lockd fscache nfs_acl auth_rpcgss sunrpc bridge stp iptable_mangle iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack nf_defrag_ipv4 iptable_filter ip_tables x_tables ext4 jbd2 crc16 dm_snapshot loop radeon ttm drm_kms_helper drm snd_pcm snd_timer i2c_algo_bit snd soundcore i2c_core snd_page_alloc i5100_edac shpchp ioatdma edac_core psmouse pci_hotplug dca evdev joydev pcspkr serio_raw dcdbas processor button acpi_processor ext3 jbd mbcache dm_mod raid10 raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid1 raid0 multipath linear md_mod sd_mod crc_t10dif sg sr_mod cdrom usbhid hid ata_generic mptsas uhci_hcd mptscsih mptbase scsi_transport_sas r8169 mii ata_piix ehci_hcd libata tg3 libphy usbcore nls_base scsi_mod thermal thermal_sys [last unloaded: scsi_wait_scan]
[1093555.812267] Pid: 0, comm: swapper Not tainted 2.6.32-5-xen-amd64 #1
[1093555.812270] Call Trace:
[1093555.812273] <IRQ> [<ffffffff812726a2>] ? dev_watchdog+0xe2/0x194
[1093555.812283] [<ffffffff812726a2>] ? dev_watchdog+0xe2/0x194
[1093555.812289] [<ffffffff8104ed9c>] ? warn_slowpath_common+0x77/0xa3
[1093555.812294] [<ffffffff812725c0>] ? dev_watchdog+0x0/0x194
[1093555.812298] [<ffffffff8104ee24>] ? warn_slowpath_fmt+0x51/0x59
[1093555.812305] [<ffffffff8101f7f0>] ? mce_setup+0xb0/0xbe
[1093555.812310] [<ffffffff81272594>] ? netif_tx_lock+0x3d/0x69
[1093555.812316] [<ffffffff8125d038>] ? netdev_drivername+0x3b/0x40
[1093555.812320] [<ffffffff812726a2>] ? dev_watchdog+0xe2/0x194
[1093555.812327] [<ffffffff8100ecf2>] ? check_events+0x12/0x20
[1093555.812333] [<ffffffff8105b46f>] ? run_timer_softirq+0x1c9/0x268
[1093555.812339] [<ffffffff81054b23>] ? __do_softirq+0xdd/0x1a2
[1093555.812345] [<ffffffff81012cac>] ? call_softirq+0x1c/0x30
[1093555.812349] [<ffffffff8101422b>] ? do_softirq+0x3f/0x7c
[1093555.812354] [<ffffffff81054992>] ? irq_exit+0x36/0x76
[1093555.812360] [<ffffffff811f1e8d>] ? xen_evtchn_do_upcall+0x33/0x42
[1093555.812365] [<ffffffff81012cfe>] ? xen_do_hypervisor_callback+0x1e/0x30
[1093555.812368] <EOI> [<ffffffff810093aa>] ? hypercall_page+0x3aa/0x1001
[1093555.812376] [<ffffffff810093aa>] ? hypercall_page+0x3aa/0x1001
[1093555.812382] [<ffffffff8100e6bb>] ? xen_safe_halt+0xc/0x15
[1093555.812386] [<ffffffff8100bfc7>] ? xen_idle+0x37/0x40
[1093555.812391] [<ffffffff81010eb1>] ? cpu_idle+0xa2/0xda
[1093555.812396] [<ffffffff81508cd1>] ? start_kernel+0x3dc/0x3e8
[1093555.812401] [<ffffffff8150ac87>] ? xen_start_kernel+0x586/0x58a
[1093555.812404] ---[ end trace ab8976cc161d6dfc ]---
[1093555.830631] r8169: pethx11: link up
[1097910.576742] tg3: pethnet: Link is down.
[1097910.598632] brnet: port 1(pethnet) entering disabled state
[1097919.919412] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1097919.919416] tg3: pethnet: Flow control is on for TX and on for RX.
[1097919.921726] brnet: port 1(pethnet) entering learning state
[1097934.920079] brnet: port 1(pethnet) entering forwarding state




-- Package-specific info:
** Version:
Linux version 2.6.32-5-xen-amd64 (Debian 2.6.32-30) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Jan 12 05:46:49 UTC 2011

** Command line:
root=/dev/mapper/vg_root-lv_ramoth ro quiet

** Tainted: W (512)
* Taint on warning.

** Kernel log:
[1446237.738757] brnet: port 1(pethnet) entering disabled state
[1446244.685874] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1446244.685879] tg3: pethnet: Flow control is on for TX and on for RX.
[1446244.688549] brnet: port 1(pethnet) entering learning state
[1446259.688104] brnet: port 1(pethnet) entering forwarding state
[1460944.690769] tg3: pethnet: Link is down.
[1460944.718891] brnet: port 1(pethnet) entering disabled state
[1460947.748065] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1460947.748070] tg3: pethnet: Flow control is on for TX and on for RX.
[1460947.750350] brnet: port 1(pethnet) entering learning state
[1460962.748090] brnet: port 1(pethnet) entering forwarding state
[1494387.761010] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1494387.761013] EDD information not available.
[1526850.729912] tg3: pethnet: Link is down.
[1526850.755081] brnet: port 1(pethnet) entering disabled state
[1526856.608532] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1526856.608537] tg3: pethnet: Flow control is on for TX and on for RX.
[1526856.610820] brnet: port 1(pethnet) entering learning state
[1526871.608029] brnet: port 1(pethnet) entering forwarding state
[1556618.262815] tg3: pethnet: Link is down.
[1556618.290530] brnet: port 1(pethnet) entering disabled state
[1556623.935944] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1556623.935948] tg3: pethnet: Flow control is on for TX and on for RX.
[1556623.938232] brnet: port 1(pethnet) entering learning state
[1556638.936022] brnet: port 1(pethnet) entering forwarding state
[1583786.561615] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1583786.561619] EDD information not available.
[1621461.586043] tg3: pethnet: Link is down.
[1621461.602640] brnet: port 1(pethnet) entering disabled state
[1621465.016943] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1621465.016948] tg3: pethnet: Flow control is on for TX and on for RX.
[1621465.019224] brnet: port 1(pethnet) entering learning state
[1621480.016050] brnet: port 1(pethnet) entering forwarding state
[1634644.950451] tg3: pethnet: Link is down.
[1634644.974799] brnet: port 1(pethnet) entering disabled state
[1634657.515770] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1634657.515774] tg3: pethnet: Flow control is on for TX and on for RX.
[1634657.518275] brnet: port 1(pethnet) entering learning state
[1634672.516025] brnet: port 1(pethnet) entering forwarding state
[1645027.362486] tg3: pethnet: Link is down.
[1645027.390899] brnet: port 1(pethnet) entering disabled state
[1645030.621162] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1645030.621166] tg3: pethnet: Flow control is on for TX and on for RX.
[1645030.623440] brnet: port 1(pethnet) entering learning state
[1645045.620021] brnet: port 1(pethnet) entering forwarding state
[1670187.219070] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1670187.219073] EDD information not available.
[1712227.484407] tg3: pethnet: Link is down.
[1712227.506405] brnet: port 1(pethnet) entering disabled state
[1712239.911264] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1712239.911268] tg3: pethnet: Flow control is on for TX and on for RX.
[1712239.913681] brnet: port 1(pethnet) entering learning state
[1712254.913212] brnet: port 1(pethnet) entering forwarding state
[1756586.515960] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1756586.515964] EDD information not available.
[1786907.763858] tg3: pethnet: Link is down.
[1786907.794655] brnet: port 1(pethnet) entering disabled state
[1786911.233357] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1786911.233361] tg3: pethnet: Flow control is on for TX and on for RX.
[1786911.235618] brnet: port 1(pethnet) entering learning state
[1786926.232021] brnet: port 1(pethnet) entering forwarding state
[1842800.580128] md: data-check of RAID array md124
[1842800.580132] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[1842800.580135] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1842800.580141] md: using 128k window, over a total of 152367365 blocks.
[1842800.845545] md: delaying data-check of md125 until md124 has finished (they share one or more physical units)
[1842800.875272] md: delaying data-check of md126 until md124 has finished (they share one or more physical units)
[1842800.902665] md: delaying data-check of md127 until md124 has finished (they share one or more physical units)
[1842988.245941] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1842988.245945] EDD information not available.
[1845612.835409] md: md124: data-check done.
[1845612.878613] md: delaying data-check of md127 until md125 has finished (they share one or more physical units)
[1845612.878624] md: delaying data-check of md126 until md125 has finished (they share one or more physical units)
[1845612.878639] md: delaying data-check of md125 until md126 has finished (they share one or more physical units)
[1845612.878649] md: delaying data-check of md126 until md127 has finished (they share one or more physical units)
[1845612.878652] md: data-check of RAID array md127
[1845612.878656] md: delaying data-check of md125 until md126 has finished (they share one or more physical units)
[1845612.878659] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[1845612.878662] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1845612.878667] md: using 128k window, over a total of 152328256 blocks.
[1849341.385159] md: md127: data-check done.
[1849341.434378] md: delaying data-check of md125 until md126 has finished (they share one or more physical units)
[1849341.434390] md: data-check of RAID array md126
[1849341.434393] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[1849341.434396] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1849341.434403] md: using 128k window, over a total of 64128 blocks.
[1849345.448321] md: md126: data-check done.
[1849345.473847] md: data-check of RAID array md125
[1849345.473852] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[1849345.473855] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for data-check.
[1849345.473862] md: using 128k window, over a total of 152327234 blocks.
[1851983.205416] md: md125: data-check done.
[1929387.609942] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[1929387.609945] EDD information not available.
[1955317.904270] tg3: pethnet: Link is down.
[1955317.926300] brnet: port 1(pethnet) entering disabled state
[1955325.275971] tg3: pethnet: Link is up at 100 Mbps, full duplex.
[1955325.275975] tg3: pethnet: Flow control is on for TX and on for RX.
[1955325.278250] brnet: port 1(pethnet) entering learning state
[1955340.276045] brnet: port 1(pethnet) entering forwarding state

** Model information
sys_vendor: Dell Inc.
product_name: PowerEdge T300
product_version:
chassis_vendor: Dell Inc.
chassis_version:
bios_vendor: Dell Inc.
bios_version: 1.2.0
board_vendor: Dell Inc.
board_name: 0TY177
board_version: A00

** Loaded modules:
Module Size Used by
tun 10908 0
cpufreq_stats 2659 0
st 30916 0
ide_gd_mod 20433 0
ide_cd_mod 24744 0
ide_core 71722 2 ide_gd_mod,ide_cd_mod
ipt_REJECT 1953 1
xt_tcpudp 2319 6
xt_state 1303 6
xt_physdev 1508 12
xen_evtchn 4339 16
xenfs 9600 1
nfsd 254782 13
exportfs 3170 1 nfsd
nfs 241066 0
lockd 57603 2 nfsd,nfs
fscache 29834 1 nfs
nfs_acl 2031 2 nfsd,nfs
auth_rpcgss 33476 2 nfsd,nfs
sunrpc 161525 15 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
bridge 39662 0
stp 1440 1 bridge
iptable_mangle 2817 0
iptable_nat 4299 1
nf_nat 13372 1 iptable_nat
nf_conntrack_ipv4 9833 9 iptable_nat,nf_nat
nf_conntrack 46519 4 xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 1139 1 nf_conntrack_ipv4
iptable_filter 2258 1
ip_tables 13899 3 iptable_mangle,iptable_nat,iptable_filter
x_tables 12845 6 ipt_REJECT,xt_tcpudp,xt_state,xt_physdev,iptable_n at,ip_tables
ext4 289033 1
jbd2 67015 1 ext4
crc16 1319 1 ext4
dm_snapshot 18481 0
loop 11799 0
radeon 574044 0
ttm 40834 1 radeon
drm_kms_helper 20065 1 radeon
drm 143361 3 radeon,ttm,drm_kms_helper
snd_pcm 60551 0
snd_timer 15582 1 snd_pcm
i2c_algo_bit 4225 1 radeon
snd 46446 2 snd_pcm,snd_timer
soundcore 4598 1 snd
i2c_core 15712 4 radeon,drm_kms_helper,drm,i2c_algo_bit
snd_page_alloc 6249 1 snd_pcm
i5100_edac 5517 0
shpchp 26264 0
ioatdma 34876 60
edac_core 29261 1 i5100_edac
psmouse 49777 0
pci_hotplug 21203 1 shpchp
dca 3761 1 ioatdma
evdev 7352 3
joydev 8459 0
pcspkr 1699 0
serio_raw 3752 0
dcdbas 5048 0
processor 35941 0
button 4650 0
acpi_processor 5087 1 processor,[permanent]
ext3 106502 5
jbd 37085 1 ext3
mbcache 5050 2 ext4,ext3
dm_mod 53754 58 dm_snapshot
raid10 17809 0
raid456 44484 0
async_raid6_recov 5170 1 raid456
async_pq 3463 2 raid456,async_raid6_recov
raid6_pq 77179 2 async_raid6_recov,async_pq
async_xor 2478 3 raid456,async_raid6_recov,async_pq
xor 4380 1 async_xor
async_memcpy 1198 2 raid456,async_raid6_recov
async_tx 1734 5 raid456,async_raid6_recov,async_pq,async_xor,async _memcpy
raid1 18431 4
raid0 5517 0
multipath 6059 0
linear 3455 0
md_mod 73808 8 raid10,raid456,raid1,raid0,multipath,linear
sd_mod 29873 18
crc_t10dif 1276 1 sd_mod
sg 18760 0
sr_mod 12602 0
cdrom 29415 2 ide_cd_mod,sr_mod
usbhid 33276 0
hid 63225 1 usbhid
ata_generic 3047 0
mptsas 29188 14
uhci_hcd 18521 0
mptscsih 16328 1 mptsas
mptbase 48382 2 mptsas,mptscsih
scsi_transport_sas 19865 1 mptsas
r8169 29261 0
mii 3210 1 r8169
ata_piix 21124 0
ehci_hcd 31151 0
libata 133632 2 ata_generic,ata_piix
tg3 95727 0
libphy 14038 1 tg3
usbcore 122034 4 usbhid,uhci_hcd,ehci_hcd
nls_base 6377 1 usbcore
scsi_mod 122133 8 st,sd_mod,sg,sr_mod,mptsas,mptscsih,scsi_transport _sas,libata
thermal 11674 0
thermal_sys 11942 2 processor,thermal

** Network interface configuration:

auto lo
iface lo inet loopback




auto brlocal brnet brx11

iface brlocal inet static
bridge_ports pethlocal
bridge_stp off
bridge_maxwait 0
address 192.168.13.1
netmask 255.255.255.0

iface brnet inet dhcp
bridge_ports pethnet

iface brx11 inet manual
bridge_ports pethx11
bridge_stp off
bridge_maxwait 0

** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: pethx11: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether 00:0f:b5:80:60:52 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:b5ff:fe80:6052/64 scope link
valid_lft forever preferred_lft forever
3: pethlocal: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:1e:4f:35:cc:e3 brd ff:ff:ff:ff:ff:ff
inet6 fe80::21e:4fff:fe35:cce3/64 scope link
valid_lft forever preferred_lft forever
4: pethnet: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
link/ether 00:1e:4f:35:cc:e4 brd ff:ff:ff:ff:ff:ff
inet6 fe80::21e:4fff:fe35:cce4/64 scope link
valid_lft forever preferred_lft forever
5: brlocal: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 00:1e:4f:35:cc:e3 brd ff:ff:ff:ff:ff:ff
inet 192.168.13.1/24 brd 192.168.13.255 scope global brlocal
inet6 fe80::21e:4fff:fe35:cce3/64 scope link
valid_lft forever preferred_lft forever
6: brnet: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 00:1e:4f:35:cc:e4 brd ff:ff:ff:ff:ff:ff
inet 192.168.0.2/24 brd 192.168.0.255 scope global brnet
inet6 fe80::21e:4fff:fe35:cce4/64 scope link
valid_lft forever preferred_lft forever
7: brx11: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN
link/ether 00:0f:b5:80:60:52 brd ff:ff:ff:ff:ff:ff
inet6 fe80::20f:b5ff:fe80:6052/64 scope link
valid_lft forever preferred_lft forever
9: vif2.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever
52: vif30.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever
53: vif30.1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever
54: vif31.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever
57: vif33.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever
74: vif42.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever
75: vif42.1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32
link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff
inet6 fe80::fcff:ffff:feff:ffff/64 scope link
valid_lft forever preferred_lft forever

*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo:26037547 161717 0 0 0 0 0 0 26037547 161717 0 0 0 0 0 0
pethx11:54343760638 187820747 0 0 0 0 0 0 380770235577 305710015 0 46 0 0 0 0
pethlocal:171817637598 333706086 0 26 0 962 0 869700 518354377801 506979348 0 0 0 0 0 0
pethnet:16677441882 28638808 0 0 0 0 0 1090 28729952901 30875915 0 0 0 0 0 0
brlocal:31583526568 66785879 0 0 0 0 0 1120505 30621116699 55976846 0 0 0 0 0 0
brnet:16157642787 28638471 0 0 0 0 0 6496 27952169829 21198919 0 0 0 0 0 0
brx11:126608783 1232115 0 0 0 0 0 1148448 1500498 35721 0 0 0 0 0 0
vif2.0:491536307149 254192902 0 0 0 0 0 0 137532422512 357079726 0 2 0 0 0 0
vif30.0: 8288430 26633 0 0 0 0 0 0 107637204 1034999 0 2 0 0 0 0
vif30.1: 0 0 0 0 0 0 0 0 2058 45 0 118866 0 0 0 0
vif31.0: 8614430 26951 0 0 0 0 0 0 106339703 1034184 0 3 0 0 0 0
vif33.0:3741449362 2062514 0 0 0 0 0 0 1914711036 4029591 0 1 0 0 0 0
vif42.0:4668116784 3037672 0 0 0 0 0 0 2432183469 3434787 0 3 0 0 0 0
vif42.1:185635084079 28534766 0 0 0 0 0 0 19483860980 86212401 0 4 0 0 0 0

*** Protocol statistics:
Ip:
83894738 total packets received
2 with invalid addresses
27936813 forwarded
0 incoming packets discarded
55861931 incoming packets delivered
77328537 requests sent out
83 fragments dropped after timeout
349 reassemblies required
50 packets reassembled ok
83 packet reassembles failed
222 fragments received ok
706 fragments created
Icmp:
104407 ICMP messages received
623 input ICMP message failed.
ICMP input histogram:
destination unreachable: 100271
echo requests: 4134
echo replies: 2
147665 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 143453
echo request: 78
echo replies: 4134
IcmpMsg:
InType0: 2
InType3: 100271
InType8: 4134
OutType0: 4134
OutType3: 143453
OutType8: 78
Tcp:
1873 active connections openings
28680 passive connection openings
312 failed connection attempts
45 connection resets received
9 connections established
54379538 segments received
47870281 segments send out
304632 segments retransmited
3 bad segments received.
1859 resets sent
Udp:
977216 packets received
32896 packets to unknown port received.
1 packet receive errors
1069146 packets sent
UdpLite:
TcpExt:
119 resets received for embryonic SYN_RECV sockets
778 TCP sockets finished time wait in fast timer
2 packets rejects in established connections because of timestamp
83268 delayed acks sent
66 delayed acks further delayed because of locked socket
Quick ack mode was activated 35766 times
15508 packets directly queued to recvmsg prequeue.
70272 bytes directly in process context from backlog
1787 bytes directly received in process context from prequeue
35748543 packet headers predicted
57 packets header predicted and directly queued to user
3689258 acknowledgments not containing data payload received
44001750 predicted acknowledgments
277417 times recovered from packet loss by selective acknowledgements
438 congestion windows recovered without slow start after partial ack
12269 TCP data loss events
TCPLostRetransmit: 42
316 timeouts after SACK recovery
2 timeouts in loss state
293428 fast retransmits
709 forward retransmits
529 retransmits in slow start
3737 other TCP timeouts
33 SACK retransmits failed
35780 DSACKs sent for old packets
4592 DSACKs received
16 connections reset due to unexpected data
14 connections reset due to early user close
596 connections aborted due to timeout
TCPDSACKIgnoredOld: 126
TCPDSACKIgnoredNoUndo: 123
TCPSpuriousRTOs: 9
TCPSackShifted: 1565289
TCPSackMerged: 1138225
TCPSackShiftFallback: 294801
IpExt:
InBcastPkts: 393932
OutBcastPkts: 17123
InOctets: -1435129164
OutOctets: 1698889668
InBcastOctets: 72654925
OutBcastOctets: 1366845

*** Device features:
brlocal: 0x111833
brnet: 0x111833
brx11: 0x1803
lo: 0x13865
pethlocal: 0x1109b3
pethnet: 0x1109b3
pethx11: 0x180
vif2.0: 0x10803
vif30.0: 0x10803
vif30.1: 0x10803
vif31.0: 0x10803
vif33.0: 0x10803
vif42.0: 0x10803
vif42.1: 0x10803

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 5100 Chipset Memory Controller Hub [8086:65c0] (rev 90)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 0
Capabilities: <access denied>

00:02.0 PCI bridge [0604]: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 [8086:65f7] (rev 90) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: dfa00000-dfbfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:03.0 PCI bridge [0604]: Intel Corporation 5100 Chipset PCI Express x4 Port 3 [8086:65e3] (rev 90) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:04.0 PCI bridge [0604]: Intel Corporation 5100 Chipset PCI Express x4 Port 4 [8086:65e4] (rev 90) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:05.0 PCI bridge [0604]: Intel Corporation 5100 Chipset PCI Express x4 Port 5 [8086:65e5] (rev 90) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:06.0 PCI bridge [0604]: Intel Corporation 5100 Chipset PCI Express x8 Port 6-7 [8086:65f9] (rev 90) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:07.0 PCI bridge [0604]: Intel Corporation 5100 Chipset PCI Express x4 Port 7 [8086:65e7] (rev 90) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:08.0 System peripheral [0880]: Intel Corporation 5100 Chipset DMA Engine [8086:65ff] (rev 90)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 1246
Region 0: Memory at df9ff800 (64-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ioatdma

00:10.0 Host bridge [0600]: Intel Corporation 5100 Chipset FSB Registers [8086:65f0] (rev 90)
Subsystem: Dell PowerEdge T300 [1028:0210]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.1 Host bridge [0600]: Intel Corporation 5100 Chipset FSB Registers [8086:65f0] (rev 90)
Subsystem: Dell PowerEdge T300 [1028:0210]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.2 Host bridge [0600]: Intel Corporation 5100 Chipset FSB Registers [8086:65f0] (rev 90)
Subsystem: Dell PowerEdge T300 [1028:0210]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:11.0 Host bridge [0600]: Intel Corporation 5100 Chipset Reserved Registers [8086:65f1] (rev 90)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:13.0 Host bridge [0600]: Intel Corporation 5100 Chipset Reserved Registers [8086:65f3] (rev 90)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:15.0 Host bridge [0600]: Intel Corporation 5100 Chipset DDR Channel 0 Registers [8086:65f5] (rev 90)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:16.0 Host bridge [0600]: Intel Corporation 5100 Chipset DDR Channel 1 Registers [8086:65f6] (rev 90)
Subsystem: Intel Corporation Device [8086:8086]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=0a, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: dfc00000-dfcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dfd00000-dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:1c.5 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 [8086:294a] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: dfe00000-dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport

00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge T300 onboard UHCI [1028:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at bc80 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge T300 onboard UHCI [1028:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at bca0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge T300 onboard UHCI [1028:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at bcc0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd

00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell PowerEdge T300 onboard UHCI [1028:0210]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at bce0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell PowerEdge T300 onboard EHCI [1028:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at df9ffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: dff00000-dfffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d7ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801IR (ICH9R) LPC Interface Controller [8086:2916] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>

00:1f.2 IDE interface [0101]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 4 port SATA IDE Controller [8086:2920] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Dell PowerEdge T300 onboard SATA Controller [1028:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 23
Region 0: I/O ports at bc20 [size=8]
Region 1: I/O ports at bc10 [size=4]
Region 2: I/O ports at bc28 [size=8]
Region 3: I/O ports at bc14 [size=4]
Region 4: I/O ports at bc40 [size=16]
Region 5: I/O ports at bc50 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix

00:1f.5 IDE interface [0101]: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller [8086:2926] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Dell PowerEdge T300 onboard SATA Controller [1028:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 22
Region 0: I/O ports at bc30 [size=8]
Region 1: I/O ports at bc18 [size=4]
Region 2: I/O ports at bc38 [size=8]
Region 3: I/O ports at bc1c [size=4]
Region 4: I/O ports at bc60 [size=16]
Region 5: I/O ports at bc70 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix

01:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express [14e4:165a]
Subsystem: Dell PowerEdge T300 Broadcom NetXtreme 5722 [1028:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1245
Region 0: Memory at dfdf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3

02:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express [14e4:165a]
Subsystem: Dell PowerEdge T300 Broadcom NetXtreme 5722 [1028:0210]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1244
Region 0: Memory at dfef0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3

03:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic SAS1068E PCI-Express Fusion-MPT SAS [1000:0058] (rev 08)
Subsystem: Dell SAS 6/iR Adapter RAID Controller [1028:1f0e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at dfbec000 (64-bit, non-prefetchable) [size=16K]
Region 3: Memory at dfbf0000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at dfa00000 [disabled] [size=1M]
Capabilities: <access denied>
Kernel driver in use: mptsas

09:00.0 PCI bridge [0604]: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A [8086:032c] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=09, secondary=0a, subordinate=0a, sec-latency=64
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: dfc00000-dfcfffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

0a:02.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Netgear GA311 [1385:311a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 67
Region 0: I/O ports at dc00 [size=256]
Region 1: Memory at dfcfff00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at dfc00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169

0b:07.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000 [1002:515e] (rev 02) (prog-if 00 [VGA controller])
Subsystem: Dell PowerEdge T300 Embedded ATI ES1000 [1028:0210]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at cc00 [size=256]
Region 2: Memory at dfff0000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at dff00000 [disabled] [size=128K]
Capabilities: <access denied>


** USB devices:
not available


-- System Information:
Debian Release: 6.0
APT prefers squeeze-updates
APT policy: (500, 'squeeze-updates'), (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.32-5-xen-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-2.6.32-5-xen-amd64 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-30 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.32-5-xen-amd64 recommends:
ii firmware-linux-free 2.6.32-30 Binary firmware for various driver

Versions of packages linux-image-2.6.32-5-xen-amd64 suggests:
pn grub <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)

Versions of packages linux-image-2.6.32-5-xen-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
ii xen-hypervisor-4.0-amd64 [xen 4.0.1-2 The Xen Hypervisor on AMD64

-- debconf information:
linux-image-2.6.32-5-xen-amd64/postinst/depmod-error-initrd-2.6.32-5-xen-amd64: false
linux-image-2.6.32-5-xen-amd64/postinst/ignoring-do-bootloader-2.6.32-5-xen-amd64:
linux-image-2.6.32-5-xen-amd64/prerm/removing-running-kernel-2.6.32-5-xen-amd64: true
linux-image-2.6.32-5-xen-amd64/postinst/missing-firmware-2.6.32-5-xen-amd64:



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20110307095042.27059.81739.reportbug@ramoth.intra. lagerbe.org">http://lists.debian.org/20110307095042.27059.81739.reportbug@ramoth.intra. lagerbe.org


All times are GMT. The time now is 07:53 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.