FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 08-01-2010, 03:13 AM
Matthias Wamser
 
Default Bug#591186: linux-image-2.6.32-5-686: Kernel panic with 2.6.32-5 and e1000 and vlan interface enabled

Package: linux-2.6
Version: 2.6.32-15
Severity: important
Tags: upstream


Hi,

i'm experiencing serious problems with the latest squeeze kernel and e1000
network card. All seems to be fine until i do *not* enable vlan interfaces.

If i add one vlan interface, the kernel panics. The output below is from a machine
with several vlan interfaces enabled in /etc/network/interfaces. All interfaces just
set up like this:

iface eth1.3 inet manual
vlan-raw-device eth1
up /sbin/ifconfig eth1.3 up

The machine panics on boot and loops in reboot / panic forever. Output of
kernel message see below.

Hardware is an ALLNET FW8888 Box with 2 82541GI Gigabit Ethernet (these
are driven by e1000 module) and 3 82574L Gigabit Network Interfaces (these are
driven by e1000e). All are onboard. I have 3 of these boxes, all 3 have
the same problem.

Problem is definitively the 82541GI Interface driven by e1000 module.

If i configure one of the e1000e interfaces with "vconfig add . and . ifconfig up"
there is no problem. If i do this with one of the e1000 interfaces the kernel
panics.

I also tried the latest e1000 module source (version 8.0.19-NAPI) from intel.com
with exactly no change. Its the same problem.

I have a debian lenny running on the same hardware box. There i had no (but other)
problems with 2.6.26. So i upgraded to backports.org kernel 2.6.32.
Since then i have regular kernel panics with 2.6.32-bpo.3-686 and 2.6.32-bpo.3-686,
sometimes just seems the network card to freeze. Everything works, link is up, but
no traffic passes through. With versions 2.6.32-bpo.4-686 and 2.6.32-bpo.5-686 i
get the panic immediately after reboot like now on squeeze.

Regards,
matthias

### Kernel message catched by serial console (Debian Squeeze, 2.6.32-5):

Setting up networking....
Loading kernel m[ 17.886179] lib80211: common routines for IEEE802.11 drivers
odules...done.
Activating lvm and md swap...done.
Checking file systems...fsck from util-linux-ng 2.17.2
done.
Mounting local filesystems...failed.
Activating swapfile swap...done.
Cleaning up temporary files....
Setting kernel variables ...done.
[ 18.923198] NET: Registered protocol family 10
[ 19.001563] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 19.090071] lo: Disabled Privacy Extensions
[ 19.141535] All bugs added by David S. Miller <davem@redhat.com>
[ 19.220674] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 19.381964] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 19.539053] Virtual device eth1.3 asks to queue packet!
[ 19.601616] Virtual device eth1.3 asks to queue packet!
[ 19.664782] ------------[ cut here ]------------
[ 19.720045] WARNING: at drivers/char/tty_ldisc.c:445 tty_ldisc_open+0x28/0x3b()
[ 19.807554] Hardware name: 945GSE
[ 19.847169] Modules linked in: 8021q ipv6 hostap_pci hostap lib80211 natsemi i2c_i801 pcspkr rng_core i2c_core evdev usbhid ata_generic uhci_hcd ahci ata_piix e1000 ide_pci_generic libata ehci_hcd usbcore [last unloaded: scsi_wait_scan]
[ 20.174205] Call Trace:
[ 20.203436] [<c011920d>] warn_slowpath_common+0x60/0x90
[ 20.267083] [<c011924a>] warn_slowpath_null+0xd/0x10
[ 20.327613] [<c028cfe3>] tty_ldisc_open+0x28/0x3b
[ 20.384990] [<c028d185>] tty_ldisc_setup+0x31/0x5e
[ 20.443430] [<c02893f3>] tty_init_dev+0x106/0x14b
[ 20.500835] [<c028eaf1>] ptmx_open+0x49/0xcc
[ 20.553032] [<c01655b2>] chrdev_open+0x15e/0x175
[ 20.609430] Virtual device eth1.3 asks to queue packet!
[ 20.672001] [<c0161c5a>] __dentry_open+0x12b/0x218
[ 20.730603] [<c0161de0>] nameidata_to_filp+0x2b/0x42
[ 20.791071] [<c0165454>] ? chrdev_open+0x0/0x175
[ 20.847410] [<c016c938>] do_filp_open+0x3bb/0x716
[ 20.904812] [<c01531b6>] ? unmap_vmas+0x27c/0x452
[ 20.962221] [<c0154cd4>] ? free_pgtables+0x69/0x81
[ 21.020650] [<c01747a3>] ? alloc_fd+0x5c/0xe0
[ 21.073891] [<c0161a2d>] do_sys_open+0x4a/0xed
[ 21.128169] [<c0161b12>] sys_open+0x1e/0x26
[ 21.179329] [<c01029b5>] syscall_call+0x7/0xb
[ 21.232574] ---[ end trace 29672952a970da4d ]---
[ 21.372312] ------------[ cut here ]------------
[ 21.427643] WARNING: at drivers/char/tty_ldisc.c:445 tty_ldisc_open+0x28/0x3b()
[ 21.515250] Hardware name: 945GSE
[ 21.554924] Modules linked in: 8021q ipv6 hostap_pci hostap lib80211 natsemi i2c_i801 pcspkr rng_core i2c_core evdev usbhid ata_generic uhci_hcd ahci ata_piix e1000 ide_pci_generic libata ehci_hcd usbcore [last unloaded: scsi_wait_scan]
[ 21.891722] Call Trace:
[ 21.920955] [<c011920d>] warn_slowpath_common+0x60/0x90
[ 21.984601] [<c011924a>] warn_slowpath_null+0xd/0x10
[ 22.045110] [<c028cfe3>] tty_ldisc_open+0x28/0x3b
[ 22.102510] [<c028d185>] tty_ldisc_setup+0x31/0x5e
[ 22.160949] [<c02893f3>] tty_init_dev+0x106/0x14b
[ 22.218355] [<c028eaf1>] ptmx_open+0x49/0xcc
[ 22.270549] [<c01655b2>] chrdev_open+0x15e/0x175
[ 22.326910] [<c0161c5a>] __dentry_open+0x12b/0x218
[ 22.385483] [<c0161de0>] nameidata_to_filp+0x2b/0x42
[ 22.445976] [<c0165454>] ? chrdev_open+0x0/0x175
[ 22.502346] [<c016c938>] do_filp_open+0x3bb/0x716
[ 22.559736] [<c01531b6>] ? unmap_vmas+0x27c/0x452
[ 22.617131] [<c0154cd4>] ? free_pgtables+0x69/0x81
[ 22.675572] [<c01747a3>] ? alloc_fd+0x5c/0xe0
[ 22.728981] [<c0161a2d>] do_sys_open+0x4a/0xed
[ 22.783209] [<c0161b12>] sys_open+0x1e/0x26
[ 22.834355] [<c01029b5>] syscall_call+0x7/0xb
[ 22.887598] ---[ end trace 29672952a970da4e ]---
[ 24.671061] Virtual device eth1.3 asks to queue packet!
[ 24.769572] ------------[ cut here ]------------
[ 24.824903] WARNING: at drivers/char/tty_ldisc.c:445 tty_ldisc_open+0x28/0x3b()
[ 24.912388] Hardware name: 945GSE
[ 24.952001] Modules linked in: 8021q ipv6 hostap_pci hostap lib80211 natsemi i2c_i801 pcspkr rng_core i2c_core evdev usbhid ata_generic uhci_hcd ahci ata_piix e1000 ide_pci_generic libata ehci_hcd usbcore [last unloaded: scsi_wait_scan]
[ 25.288601] Call Trace:
[ 25.317836] [<c011920d>] warn_slowpath_common+0x60/0x90
[ 25.381494] [<c011924a>] warn_slowpath_null+0xd/0x10
[ 25.441989] [<c028cfe3>] tty_ldisc_open+0x28/0x3b
[ 25.499396] [<c028d185>] tty_ldisc_setup+0x31/0x5e
[ 25.557830] [<c02893f3>] tty_init_dev+0x106/0x14b
[ 25.615224] [<c028eaf1>] ptmx_open+0x49/0xcc
[ 25.667324] [<c01655b2>] chrdev_open+0x15e/0x175
[ 25.723862] [<c0161c5a>] __dentry_open+0x12b/0x218
[ 25.782244] [<c0161de0>] nameidata_to_filp+0x2b/0x42
[ 25.842747] [<c0165454>] ? chrdev_open+0x0/0x175
[ 25.899106] [<c016c938>] do_filp_open+0x3bb/0x716
[ 25.956516] [<c01531b6>] ? unmap_vmas+0x27c/0x452
[ 26.013905] [<c0154cd4>] ? free_pgtables+0x69/0x81
[ 26.072348] [<c01747a3>] ? alloc_fd+0x5c/0xe0
[ 26.125585] [<c0161a2d>] do_sys_open+0x4a/0xed
[ 26.179864] [<c0161b12>] sys_open+0x1e/0x26
[ 26.231033] [<c01029b5>] syscall_call+0x7/0xb
[ 26.284261] ---[ end trace 29672952a970da4f ]---
[ 26.658313] BUG: unable to handle kernel NULL pointer dereference at 00000005
[ 26.659009] IP: [<c01473cd>] __free_pages+0xb/0x2d
[ 26.659009] *pde = 00000000
[ 26.659009] Oops: 0002 [#1] PREEMPT
[ 26.659009] last sysfs file: /sys/class/net/eth1.3/uevent
[ 26.659009] Modules linked in: 8021q ipv6 hostap_pci hostap lib80211 natsemi i2c_i801 pcspkr rng_core i2c_core evdev usbhid ata_generic uhci_hcd ahci ata_piix e1000 ide_pci_generic libata ehci_hcd usbcore [last unloaded: scsi_wait_scan]
[ 26.659009]
[ 26.659009] EIP: 0060:[<c01473cd>] EFLAGS: 00010246 CPU: 0
[ 26.659009] EIP is at __free_pages+0xb/0x2d
[ 26.659009] EAX: 00000005 EBX: 00000000 ECX: 00000001 EDX: 00000000
[ 26.659009] ESI: f6a0c600 EDI: f6a0c780 EBP: f6413d94 ESP: f6413d90
[ 26.659009] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
[ 26.659009] Process stat (pid: 1727, ti=f6412000 task=f6a3d220 task.ti=f6412000)
[ 26.659009] Stack:
[ 26.659009] 00000010 f6413da8 c0168972 f6c0ce60 f6c0ce60 f6a0c600 f6413db4 c016898f
[ 26.659009] <0> 00000000 f6413dd0 c01689da 00000001 f6c0ced0 00000008 f696c440 f6c0ce60
[ 26.659009] <0> f6413dd8 c0168a48 f6413df4 c0163f7a f6fae814 f700e540 f696c440 00000000
[ 26.659009] Call Trace:
[ 26.659009] [<c0168972>] ? __free_pipe_info+0x36/0x42
[ 26.659009] [<c016898f>] ? free_pipe_info+0x11/0x1e
[ 26.659009] [<c01689da>] ? pipe_release+0x3e/0x86
[ 26.659009] [<c0168a48>] ? pipe_write_release+0xf/0x11
[ 26.659009] [<c0163f7a>] ? __fput+0xc7/0x178
[ 26.659009] [<c0164043>] ? fput+0x18/0x1a
[ 26.659009] [<c016191f>] ? filp_close+0x51/0x5b
[ 26.659009] [<c011a735>] ? put_files_struct+0x67/0xa9
[ 26.659009] [<c011a7b0>] ? exit_files+0x39/0x3c
[ 26.659009] [<c011ba5c>] ? do_exit+0x15e/0x542
[ 26.659009] [<c0120f2b>] ? recalc_sigpending+0x11/0x30
[ 26.659009] [<c0123486>] ? dequeue_signal+0x91/0xfc
[ 26.659009] [<c011bea2>] ? do_group_exit+0x62/0x85
[ 26.659009] [<c0123a3e>] ? get_signal_to_deliver+0x374/0x39a
[ 26.659009] [<c0101da8>] ? do_notify_resume+0x67/0x712
[ 26.659009] [<c0162e04>] ? do_sync_write+0xaa/0xe8
[ 26.659009] [<c015c787>] ? free_page_and_swap_cache+0x35/0x38
[ 26.659009] [<c0175cdc>] ? mntput_no_expire+0x19/0x8f
[ 26.659009] [<c0162d5a>] ? do_sync_write+0x0/0xe8
[ 26.659009] [<c016365d>] ? vfs_write+0x8c/0x11b
[ 26.659009] [<c0163785>] ? sys_write+0x3b/0x60
[ 26.659009] [<c0102a54>] ? work_notifysig+0x9/0x15
[ 26.659009] Code: 06 83 ee 04 8b 57 04 e8 22 fe ff ff 4b 79 f0 5b 5e 5f 5d c3 55 31 d2 89 e5 e8 10 fe ff ff 5d c3 55 89 c1 89 e5 8d 40 04 53 89 d3 <ff> 08 0f 94 c2 84 d2 74 16 85 db 75 09 89 c8 e8 d5 ff ff ff eb
[ 26.659009] EIP: [<c01473cd>] __free_pages+0xb/0x2d SS:ESP 0068:f6413d90
[ 26.659009] CR2: 0000000000000005
[ 29.708244] BUG: unable to handle kernel NULL pointer dereference at 00000004
[ 29.709004] IP: [<c02f2b3d>] neigh_invalidate+0x7a/0x9b
[ 29.709004] *pde = 00000000
[ 29.709004] Oops: 0002 [#2] PREEMPT
[ 29.709004] last sysfs file: /sys/class/net/eth1.3/uevent
[ 29.709004] Modules linked in: 8021q ipv6 hostap_pci hostap lib80211 natsemi i2c_i801 pcspkr rng_core i2c_core evdev usbhid ata_generic uhci_hcd ahci ata_piix e1000 ide_pci_generic libata ehci_hcd usbcore [last unloaded: scsi_wait_scan]
[ 29.709004]
[ 29.709004] EIP: 0060:[<c02f2b3d>] EFLAGS: 00010246 CPU: 0
[ 29.709004] EIP is at neigh_invalidate+0x7a/0x9b
[ 29.709004] EAX: f6a49890 EBX: f647f500 ECX: f7013a40 EDX: 00000000
[ 29.709004] ESI: f6a49840 EDI: f6a49890 EBP: f6413b88 ESP: f6413b7c
[ 29.709004] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
[ 29.709004] Process stat (pid: 1727, ti=f6412000 task=f6a3d220 task.ti=f6412000)
[ 29.709004] Stack:
[ 29.709004] f6a49840 fffbe414 00000001 f6413b9c c02f409e c04d1b40 00000101 c02f3f4f
[ 29.709004] <0> f6413bd0 c012086e f6413bbc f6a49840 c04d294c c04d274c c04d254c c04d234c
[ 29.709004] <0> f6413bbc f6413bbc 00000001 00000004 00000101 f6413bec c011cfd4 00000101
[ 29.709004] Call Trace:
[ 29.709004] [<c02f409e>] ? neigh_timer_handler+0x14f/0x219
[ 29.709004] [<c02f3f4f>] ? neigh_timer_handler+0x0/0x219
[ 29.709004] [<c012086e>] ? run_timer_softirq+0x124/0x187
[ 29.709004] [<c011cfd4>] ? __do_softirq+0x5e/0xca
[ 29.709004] [<c011d065>] ? do_softirq+0x25/0x2a
[ 29.709004] [<c011d188>] ? irq_exit+0x28/0x61
[ 29.709004] [<c010bf3c>] ? smp_apic_timer_interrupt+0x63/0x6e
[ 29.709004] [<c0102fea>] ? apic_timer_interrupt+0x2a/0x30
[ 29.709004] [<c0110000>] ? request_microcode_fw+0x22f/0x2cb
[ 29.709004] [<c0104dfe>] ? oops_end+0x2c/0x6d
[ 29.709004] [<c0110692>] ? no_context+0x10b/0x115
[ 29.709004] [<c01107f6>] ? __bad_area_nosemaphore+0x15a/0x162
[ 29.709004] [<c0114721>] ? set_next_entity+0x2c/0x52
[ 29.709004] [<c0114876>] ? pick_next_task_fair+0x83/0xa1
[ 29.709004] [<c0363b6e>] ? schedule+0x1db/0x382
[ 29.709004] [<c011d038>] ? __do_softirq+0xc2/0xca
[ 29.709004] [<c011080b>] ? bad_area_nosemaphore+0xd/0x10
[ 29.709004] [<c0110a42>] ? do_page_fault+0xe7/0x1bf
[ 29.709004] [<c011095b>] ? do_page_fault+0x0/0x1bf
[ 29.709004] [<c036542e>] ? error_code+0x5e/0x70
[ 29.709004] [<c014007b>] ? handle_nested_irq+0x5f/0x94
[ 29.709004] [<c011095b>] ? do_page_fault+0x0/0x1bf
[ 29.709004] [<c01473cd>] ? __free_pages+0xb/0x2d
[ 29.709004] [<c0168972>] ? __free_pipe_info+0x36/0x42
[ 29.709004] [<c016898f>] ? free_pipe_info+0x11/0x1e
[ 29.709004] [<c01689da>] ? pipe_release+0x3e/0x86
[ 29.709004] [<c0168a48>] ? pipe_write_release+0xf/0x11
[ 29.709004] [<c0163f7a>] ? __fput+0xc7/0x178
[ 29.709004] [<c0164043>] ? fput+0x18/0x1a
[ 29.709004] [<c016191f>] ? filp_close+0x51/0x5b
[ 29.709004] [<c011a735>] ? put_files_struct+0x67/0xa9
[ 29.709004] [<c011a7b0>] ? exit_files+0x39/0x3c
[ 29.709004] [<c011ba5c>] ? do_exit+0x15e/0x542
[ 29.709004] [<c0120f2b>] ? recalc_sigpending+0x11/0x30
[ 29.709004] [<c0123486>] ? dequeue_signal+0x91/0xfc
[ 29.709004] [<c011bea2>] ? do_group_exit+0x62/0x85
[ 29.709004] [<c0123a3e>] ? get_signal_to_deliver+0x374/0x39a
[ 29.709004] [<c0101da8>] ? do_notify_resume+0x67/0x712
[ 29.709004] [<c0162e04>] ? do_sync_write+0xaa/0xe8
[ 29.709004] [<c015c787>] ? free_page_and_swap_cache+0x35/0x38
[ 29.709004] [<c0175cdc>] ? mntput_no_expire+0x19/0x8f
[ 29.709004] [<c0162d5a>] ? do_sync_write+0x0/0xe8
[ 29.709004] [<c016365d>] ? vfs_write+0x8c/0x11b
[ 29.709004] [<c0163785>] ? sys_write+0x3b/0x60
[ 29.709004] [<c0102a54>] ? work_notifysig+0x9/0x15
[ 29.709004] Code: ff ff 40 14 80 7e 1d 20 75 36 8b 1f 39 fb 74 30 85 db 74 2c ff 4e 58 8b 13 8b 43 04 c7 03 00 00 00 00 c7 43 04 00 00 00 00 89 10 <89> 42 04 89 e0 25 00 e0 ff ff ff 48 14 f6 40 08 08 74 b2 eb ab
[ 29.709004] EIP: [<c02f2b3d>] neigh_invalidate+0x7a/0x9b SS:ESP 0068:f6413b7c
[ 29.709004] CR2: 0000000000000004
[ 34.170188] ---[ end trace 29672952a970da50 ]---
[ 34.225484] Kernel panic - not syncing: Fatal exception in interrupt
[ 34.301496] Rebooting in 30 seconds..

### End of kernel message

-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-15) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-1) ) #1 SMP Tue Jun 1 04:59:47 UTC 2010

** Command line:
root=LABEL=ROOT_FS

** Not tainted

** Kernel log:
[ 3.066821] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.066944] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.067122] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fc00
[ 3.067354] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.067436] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.067533] usb usb4: Product: UHCI Host Controller
[ 3.067607] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 3.067682] usb usb4: SerialNumber: 0000:00:1d.2
[ 3.068069] usb usb4: configuration #1 chosen from 1 choice
[ 3.068302] hub 4-0:1.0: USB hub found
[ 3.068396] hub 4-0:1.0: 2 ports detected
[ 3.068674] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 3.068770] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 3.068785] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.068889] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 3.070811] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000fb00
[ 3.071068] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.071149] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.071251] usb usb5: Product: UHCI Host Controller
[ 3.071324] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 3.071399] usb usb5: SerialNumber: 0000:00:1d.3
[ 3.072050] usb usb5: configuration #1 chosen from 1 choice
[ 3.072467] hub 5-0:1.0: USB hub found
[ 3.072567] hub 5-0:1.0: 2 ports detected
[ 3.074031] ata6: port disabled. ignoring.
[ 3.093124] e1000: 0000:05:0a.0: e1000_probe: (PCI:33MHz:32-bit) 00:0f:c9:04:db:56
[ 3.354030] e1000: eth3: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 3.354222] aic7xxx 0000:05:0c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.376068] ata3: SATA link down (SStatus 0 SControl 300)
[ 3.376203] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 3.376824] ata1.00: ATA-7: takeMS SSD TMS64GSSDM25SU22, 090508S, max UDMA/133
[ 3.376926] ata1.00: 119439360 sectors, multi 1: LBA48
[ 3.377814] ata1.00: configured for UDMA/133
[ 3.378280] scsi 0:0:0:0: Direct-Access ATA takeMS SSD TMS64 0905 PQ: 0 ANSI: 5
[ 3.445252] sd 0:0:0:0: [sda] 119439360 512-byte logical blocks: (61.1 GB/56.9 GiB)
[ 3.445695] sd 0:0:0:0: [sda] Write Protect is off
[ 3.445775] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.445928] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 3.446811] sda: sda1
[ 3.450226] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.568054] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 3.744251] usb 2-2: New USB device found, idVendor=046d, idProduct=c315
[ 3.744333] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.744407] usb 2-2: Product: Logitech USB Keyboard
[ 3.744473] usb 2-2: Manufacturer: Logitech
[ 3.745842] usb 2-2: configuration #1 chosen from 1 choice
[ 3.798584] usbcore: registered new interface driver hiddev
[ 3.813491] input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input0
[ 3.813940] generic-usb 0003:046D:C315.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:1d.0-2/input0
[ 3.814137] usbcore: registered new interface driver usbhid
[ 3.814447] usbhid: v2.6:USB HID core driver
[ 3.836498] 0000:04:00.0: eth4: (PCI Express:2.5GB/s:Width x1) 00:0f:c9:04:db:55
[ 3.836599] 0000:04:00.0: eth4: Intel(R) PRO/1000 Network Connection
[ 3.836762] 0000:04:00.0: eth4: MAC: 2, PHY: 1, PBA No: ffffff-0ff
[ 18.564060] scsi6 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
[ 18.564068] <Adaptec 29160 Ultra160 SCSI adapter>
[ 18.564074] aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
[ 18.564079]
[ 18.565136] e1000 0000:05:0b.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 18.827788] e1000: 0000:05:0b.0: e1000_probe: (PCI:33MHz:32-bit) 00:0f:c9:04:db:57
[ 19.087035] e1000: eth5: e1000_probe: Intel(R) PRO/1000 Network Connection
[ 19.204334] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 19.204447] All bugs added by David S. Miller <davem@redhat.com>
[ 19.646693] udev: starting version 158
[ 20.386713] ACPI: SSDT 7f6e7b00 002AE (v01 PmRef Cpu0Ist 00003000 INTL 20050930)
[ 20.387873] processor LNXCPU:00: registered as cooling_device1
[ 20.451056] udev: renamed network interface eth1_rename to eth2
[ 20.458343] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 20.458479] ACPI: Power Button [PWRB]
[ 20.492752] ACPI: SSDT 7f6e7fc0 00152 (v01 PmRef Cpu1Ist 00003000 INTL 20050930)
[ 20.515224] processor LNXCPU:01: registered as cooling_device2
[ 20.515763] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 20.515881] ACPI: Power Button [PWRF]
[ 20.647256] udev: renamed network interface eth3 to eth1
[ 20.652165] udev: renamed network interface eth2_rename to eth3
[ 20.786095] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 20.839566] intel_rng: Firmware space is locked read-only. If you can't or
[ 20.839578] intel_rng: don't want to disable this in firmware setup, and if
[ 20.839588] intel_rng: you are certain that your system has a functional
[ 20.839596] intel_rng: RNG, try using the 'no_fwh_detect' option.
[ 20.956479] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 21.138548] [drm] Initialized drm 1.1.0 20060810
[ 21.326879] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 21.327031] pci 0000:00:02.0: setting latency timer to 64
[ 21.353223] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 21.397048] Error: Driver 'pcspkr' is already registered, aborting...
[ 21.568862] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
[ 21.647482] natsemi dp8381x driver, version 2.1, Sept 11, 2006
[ 21.647492] originally by Donald Becker <becker@scyld.com>
[ 21.647501] 2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
[ 21.673787] lib80211: common routines for IEEE802.11 drivers
[ 21.673878] lib80211_crypt: registered algorithm 'NULL'
[ 22.365693] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.430484] e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 25.431458] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 36.132021] eth0: no IPv6 routers present
[ 95.406534] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
[ 169.932213] e1000 0000:05:0b.0: PCI INT A disabled
[ 170.076193] e1000 0000:05:0a.0: PCI INT A disabled
[ 1978.712091] usb 2-2: USB disconnect, address 2

** Model information
not available

** Loaded modules:
Module Size Used by
hostap_pci 34480 0
hostap 76764 1 hostap_pci
lib80211 2870 2 hostap_pci,hostap
natsemi 19391 0
snd_pcm 47214 0
i915 219952 0
snd_timer 12258 1 snd_pcm
drm_kms_helper 18305 1 i915
snd 34363 2 snd_pcm,snd_timer
drm 112020 2 i915,drm_kms_helper
soundcore 3450 1 snd
i2c_algo_bit 3497 1 i915
snd_page_alloc 5045 1 snd_pcm
tpm_tis 5496 0
i2c_i801 6462 0
video 14605 1 i915
tpm 8137 1 tpm_tis
tpm_bios 3569 1 tpm
pcspkr 1207 0
serio_raw 2916 0
i2c_core 12696 5 i915,drm_kms_helper,drm,i2c_algo_bit,i2c_i801
evdev 5609 0
rng_core 2178 0
output 1204 1 video
button 3598 1 i915
processor 26599 0
ext2 46293 1
mbcache 3762 1 ext2
8021q 14090 0
garp 4134 1 8021q
stp 996 1 garp
usbhid 27980 0
hid 50629 1 usbhid
sd_mod 25869 2
crc_t10dif 1012 1 sd_mod
ata_generic 2019 0
fan 2586 0
thermal 9206 0
ata_piix 17640 0
uhci_hcd 16057 0
ahci 27246 1
ehci_hcd 27763 0
aic7xxx 95155 0
scsi_transport_spi 14866 1 aic7xxx
libata 115665 3 ata_generic,ata_piix,ahci
scsi_mod 101401 4 sd_mod,aic7xxx,scsi_transport_spi,libata
usbcore 98402 4 usbhid,uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore
thermal_sys 9378 4 video,processor,fan,thermal
e1000e 120190 0

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac] (rev 03)
Subsystem: Intel Corporation Mobile 945GME Express Memory Controller Hub [8086:27ac]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=09 <?>
Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Mobile 945GME Express Integrated Graphics Controller [8086:27ae]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ff00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at fdf80000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Intel Corporation Device [8086:27ae]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: Memory at fde80000 (32-bit, non-prefetchable) [disabled] [size=512K]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: fd900000-fd9fffff
Prefetchable memory behind bridge: 00000000fd600000-00000000fd6fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #16, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=01 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport

00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fd500000-fd5fffff
Prefetchable memory behind bridge: 00000000fd400000-00000000fd4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #17, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=02 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport

00:1c.2 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fdc00000-00000000fdcfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #18, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4179
Capabilities: [90] Subsystem: Intel Corporation N10/ICH 7 Family PCI Express Port 3 [8086:27d4]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=03 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport

00:1c.3 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal+ Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
Slot #19, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 4181
Capabilities: [90] Subsystem: Intel Corporation N10/ICH 7 Family PCI Express Port 4 [8086:27d6]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed+ WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [180 v1] Root Complex Link
Desc: PortNumber=04 ComponentID=02 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=02 AssocRCRB- LinkType=MemMapped LinkValid+
Addr: 00000000fed1c001
Kernel driver in use: pcieport

00:1d.0 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at fe00 [size=32]
Kernel driver in use: uhci_hcd

00:1d.1 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at fd00 [size=32]
Kernel driver in use: uhci_hcd

00:1d.2 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at fc00 [size=32]
Kernel driver in use: uhci_hcd

00:1d.3 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at fb00 [size=32]
Kernel driver in use: uhci_hcd

00:1d.7 USB Controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fd800000-fd8fffff
Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Intel Corporation 82801 Mobile PCI Bridge [8086:2448]

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at f800 [size=16]
Kernel driver in use: ata_piix

00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller [8086:27c5] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device [8086:27c4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 35
Region 0: I/O ports at f700 [size=8]
Region 1: I/O ports at f600 [size=4]
Region 2: I/O ports at f500 [size=8]
Region 3: I/O ports at f400 [size=4]
Region 4: I/O ports at f300 [size=16]
Region 5: Memory at fdffc000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0300c Data: 41c9
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ahci

00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02)
Subsystem: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus

01:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fd9c0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 9f00 [size=32]
Region 3: Memory at fd9fc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: e1000e

02:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fd5c0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at df00 [size=32]
Region 3: Memory at fd5fc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: e1000e

03:00.0 Ethernet controller [0200]: Intel Corporation 82574L Gigabit Network Connection [8086:10d3]
Subsystem: Intel Corporation Device [8086:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fddc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at cf00 [size=32]
Region 3: Memory at fddfc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [a0] MSI-X: Enable+ Count=5 Masked-
Vector table: BAR=3 offset=00000000
PBA: BAR=3 offset=00002000
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Kernel driver in use: e1000e

04:00.0 Ethernet controller [0200]: Intel Corporation 82572EI Gigabit Ethernet Controller (Fiber) [8086:107e] (rev 06)
Subsystem: Intel Corporation PRO/1000 PF Server Adapter [8086:1094]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 34
Region 0: Memory at fdbe0000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at fdbc0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bf00 [size=32]
Expansion ROM at fdba0000 [disabled] [size=128K]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 41b9
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 <4us, L1 <64us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP+ Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-0f-c9-ff-ff-04-db-55
Kernel driver in use: e1000e

05:0a.0 Ethernet controller [0200]: Intel Corporation 82541GI Gigabit Ethernet Controller [8086:1076] (rev 05)
Subsystem: Intel Corporation PRO/1000 MT Network Connection [8086:1076]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fd8a0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at af00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-

05:0b.0 Ethernet controller [0200]: Intel Corporation 82541GI Gigabit Ethernet Controller [8086:1076] (rev 05)
Subsystem: Intel Corporation PRO/1000 MT Network Connection [8086:1076]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fd8c0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at ae00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=8 RSCEM- 266MHz- 533MHz-

05:0c.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m [9005:0080] (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller [9005:e2a0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 40 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
BIST result: 00
Region 0: I/O ports at ac00 [disabled] [size=256]
Region 1: Memory at fd8ff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at fd700000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: aic7xxx


** USB devices:
not available


-- System Information:
Debian Release: squeeze/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)

Kernel: Linux 2.6.32-5-686 (SMP w/2 CPU cores)
Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.33 Debian configuration management sy
ii initramfs-tools [linux-initra 0.97.2 tools for generating an initramfs
ii linux-base 2.6.32-15 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-15 Binary firmware for various driver
pn libc6-i686 <none> (no description available)

Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub-legacy [grub] 0.97-61 GRand Unified Bootloader (Legacy v
ii lilo 1:22.8-8.1 LInux LOader - The Classic OS load
pn linux-doc-2.6.32 <none> (no description available)

Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.26 Binary firmware for various driver
ii firmware-linux-nonfree 0.26 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)

-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/prerm/would-invalidate-boot-loader-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/bootloader-test-error-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/bootloader-error-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20100801031353.3270.91792.reportbug@fw02">http://lists.debian.org/20100801031353.3270.91792.reportbug@fw02
 

Thread Tools




All times are GMT. The time now is 01:38 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org