FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 03-01-2010, 02:29 AM
Gerry Butler
 
Default Bug#572024: linux-image-2.6.32-trunk-amd64: During boot, Kernel 2.6.32 prints trace to screen then hangs

Package: linux-2.6
Version: 2.6.32-5
Severity: important

Early in the boot process, kernel writes a trace to the screen then freezes.

The problem is intermittent. About one boot attempt in 5 succeeds.

Waiting a several minutes does not unfreeze the boot.

I am preparing this report under 2.6.31, as I have not succeeded in the last several attempts to boot 2.6.32.

I have a photo of the screen at the freeze point, which I will try to send as an attachment.

I have pasted an extract from syslog at the end of this report.

This problem arose when I was attempting to recreate Bug#557033, but I have no reason to believe it is related.

The computer is Intel core i7 with raid 1 (mirrored).



-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
not available

** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).

# The loopback network interface
auto lo
iface lo inet loopback

# The primary network interface
allow-hotplug eth1
iface eth1 inet dhcp

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Clarksfield/Lynnfield DMI [8086:d131] (rev 11)
Subsystem: Giga-byte Technology Device [1458:5000]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

00:03.0 PCI bridge [0604]: Intel Corporation Clarksfield/Lynnfield PCI Express Root Port 1 [8086:d138] (rev 11) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: f6000000-f9ffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:08.0 System peripheral [0880]: Intel Corporation Clarksfield/Lynnfield System Management Registers [8086:d155] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

00:08.1 System peripheral [0880]: Intel Corporation Clarksfield/Lynnfield Semaphore and Scratchpad Registers [8086:d156] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

00:08.2 System peripheral [0880]: Intel Corporation Clarksfield/Lynnfield System Control and Status Registers [8086:d157] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

00:08.3 System peripheral [0880]: Intel Corporation Clarksfield/Lynnfield Miscellaneous Registers [8086:d158] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.0 System peripheral [0880]: Intel Corporation Device [8086:d150] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.1 System peripheral [0880]: Intel Corporation Device [8086:d151] (rev 11)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:1a.0 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b3b] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at ff00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.1 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b3e] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at fe00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.2 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b3f] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at fd00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.7 USB Controller [0c03]: Intel Corporation Ibex Peak USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbfff000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1b.0 Audio device [0403]: Intel Corporation Ibex Peak High Definition Audio [8086:3b56] (rev 05)
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fbff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation Ibex Peak PCI Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fbd00000-fbdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.1 PCI bridge [0604]: Intel Corporation Ibex Peak PCI Express Root Port 2 [8086:3b44] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fbb00000-fbbfffff
Prefetchable memory behind bridge: 00000000fba00000-00000000fbafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.3 PCI bridge [0604]: Intel Corporation Ibex Peak PCI Express Root Port 4 [8086:3b48] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fbe00000-fbefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b36] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at fc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b37] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at fb00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b38] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at fa00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.3 USB Controller [0c03]: Intel Corporation Ibex Peak USB Universal Host Controller [8086:3b39] (rev 05) (prog-if 00 [UHCI])
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at f900 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation Ibex Peak USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20 [EHCI])
Subsystem: Giga-byte Technology Device [1458:5006]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fbffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fbc00000-fbcfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation Ibex Peak LPC Interface Controller [8086:3b02] (rev 05)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>

00:1f.2 RAID bus controller [0104]: Intel Corporation 82801 SATA RAID Controller [8086:2822] (rev 05)
Subsystem: Giga-byte Technology Device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 34
Region 0: I/O ports at f800 [size=8]
Region 1: I/O ports at f700 [size=4]
Region 2: I/O ports at f600 [size=8]
Region 3: I/O ports at f500 [size=4]
Region 4: I/O ports at f400 [size=32]
Region 5: Memory at fbffd000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

00:1f.3 SMBus [0c05]: Intel Corporation Ibex Peak SMBus Controller [8086:3b30] (rev 05)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fbffc000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0500 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

01:00.0 VGA compatible controller [0300]: nVidia Corporation G94 [GeForce 9600 GT] [10de:0622] (rev a1) (prog-if 00 [VGA controller])
Subsystem: XFX Pine Group Inc. Device [1682:238a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 12
Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f6000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at af00 [size=128]
[virtual] Expansion ROM at f9000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel modules: nvidiafb

02:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at fbdfe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

02:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at ef00 [size=8]
Region 1: I/O ports at ee00 [size=4]
Region 2: I/O ports at ed00 [size=8]
Region 3: I/O ports at ec00 [size=4]
Region 4: I/O ports at eb00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
Kernel modules: ide-pci-generic, ata_generic, pata_jmicron

03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 03)
Subsystem: Giga-byte Technology Device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 33
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fbaff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fbaf8000 (64-bit, prefetchable) [size=16K]
[virtual] Expansion ROM at fba00000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

04:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 03) (prog-if 01 [AHCI 1.0])
Subsystem: Giga-byte Technology Device [1458:b000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 5: Memory at fbefe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

04:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 03) (prog-if 85 [Master SecO PriO])
Subsystem: Giga-byte Technology Device [1458:b000]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 16
Region 0: I/O ports at cf00 [size=8]
Region 1: I/O ports at ce00 [size=4]
Region 2: I/O ports at cd00 [size=8]
Region 3: I/O ports at cc00 [size=4]
Region 4: I/O ports at cb00 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_jmicron
Kernel modules: ide-pci-generic, ata_generic, pata_jmicron

05:04.0 Ethernet controller [0200]: Accton Technology Corporation SMC2-1211TX [1113:1211] (rev 10)
Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter [1113:1211]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at be00 [size=256]
Region 1: Memory at fbcff000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
Kernel modules: 8139too


** USB devices:
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 009 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 002: ID 046d:c529 Logitech, Inc.
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 03f0:0801 Hewlett-Packard ScanJet 7400c
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


-- System Information:
Debian Release: 5.0.4
APT prefers stable
APT policy: (990, 'stable'), (500, 'unstable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.31-1-amd64 (SMP w/8 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.32-trunk-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo

Versions of packages linux-image-2.6.32-trunk-amd64 recommends:
ii firmware-linux-free 2.6.32-7 Binary firmware for various driver

Versions of packages linux-image-2.6.32-trunk-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.32 <none> (no description available)

Versions of packages linux-image-2.6.32-trunk-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)

-- debconf information:
linux-image-2.6.32-trunk-amd64/postinst/bootloader-error-2.6.32-trunk-amd64:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-trunk-amd64/postinst/depmod-error-initrd-2.6.32-trunk-amd64: false
linux-image-2.6.32-trunk-amd64/prerm/removing-running-kernel-2.6.32-trunk-amd64: true
linux-image-2.6.32-trunk-amd64/postinst/bootloader-test-error-2.6.32-trunk-amd64:
* linux-image-2.6.32-trunk-amd64/postinst/missing-firmware-2.6.32-trunk-amd64:
linux-image-2.6.32-trunk-amd64/prerm/would-invalidate-boot-loader-2.6.32-trunk-amd64: true



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20100301032927.6039.98968.reportbug@KEPLER2.WORKGR OUP">http://lists.debian.org/20100301032927.6039.98968.reportbug@KEPLER2.WORKGR OUP
 
Old 04-11-2010, 02:38 AM
Ben Hutchings
 
Default Bug#572024: linux-image-2.6.32-trunk-amd64: During boot, Kernel 2.6.32 prints trace to screen then hangs

Version: 2.6.32-10

On Mon, 2010-03-01 at 14:29 +1100, Gerry Butler wrote:
> Package: linux-2.6
> Version: 2.6.32-5
> Severity: important
>
> Early in the boot process, kernel writes a trace to the screen then freezes.
>
> The problem is intermittent. About one boot attempt in 5 succeeds.
>
> Waiting a several minutes does not unfreeze the boot.
[...]

I believe this was fixed in Linux 2.6.32.10 by the following change:

commit 3048a0dbd810980f67882a8b6745d4a6ff24c53e
Author: Tejun Heo <tj@kernel.org>
Date: Fri Feb 5 17:57:02 2010 +0900

driver-core: fix race condition in get_device_parent()

This was included in Debian kernel package version 2.6.32-10. Let us
know if this doesn't fix the problem for you.

Ben.

--
Ben Hutchings
Once a job is fouled up, anything done to improve it makes it worse.
 

Thread Tools




All times are GMT. The time now is 10:02 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org