FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 03-21-2009, 02:09 PM
Geert-Jan Hut
 
Default Bug#520645: linux-image-2.6.26-1-amd64: after update, system doesn't boot because lilo can't find boot device.

Package: linux-image-2.6.26-1-amd64
Version: 2.6.26-13lenny2
Severity: important

Today updated the package to the updated version distributed. When rebooting after the install, the system halted because no boot device couldn't be found. Restarting with providing the parameter 'root=/dev/vg00/root' at the Lilo boot prompt (e.g. using 'Linux root=/dev/vg00/root' as lilo boot command) allowed the sytem to start up, afterwards running the lilo command as root allowed the system to boot up without any boot parameters.

I had this same problem direcly after upgrading to lenny, as I remember then it turned out that the major/minor node number that was used to identify the boot partition was wrong, i.e. pointed to the wrong partition. I use software disk mirroring with lvm2, the node numbers were from the wrong partition.

As running lilo immediately solved the problem (it has a root=/dev/mapper/vg00-root device specified in /etc/lilo.conf) I assume that the update process is missing this command.

Regards, Geert-Jan.

-- Package-specific info:
** Version:
Linux version 2.6.26-1-amd64 (Debian 2.6.26-13lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Fri Mar 13 17:46:45 UTC 2009

** Command line:
auto BOOT_IMAGE=Linux ro root=fd01

** Not tainted

** Kernel log:
[ 10.090313] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.090313] sda: sda1 sda2
[ 10.114049] sd 2:0:0:0: [sda] Attached SCSI disk
[ 10.114049] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 10.114049] sd 3:0:0:0: [sdb] Write Protect is off
[ 10.114049] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 10.114049] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.114049] sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors (250059 MB)
[ 10.114049] sd 3:0:0:0: [sdb] Write Protect is off
[ 10.114049] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 10.114049] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.114049] sdb: sdb1 sdb2
[ 10.118053] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 10.303092] md: raid1 personality registered for level 1
[ 10.311943] md: md0 stopped.
[ 10.351946] md: bind<sdb1>
[ 10.352137] md: bind<sda1>
[ 10.363664] raid1: raid set md0 active with 2 out of 2 mirrors
[ 10.364731] md: md1 stopped.
[ 10.388203] md: bind<sdb2>
[ 10.388394] md: bind<sda2>
[ 10.402145] raid1: raid set md1 active with 2 out of 2 mirrors
[ 10.500376] device-mapper: uevent: version 1.0.3
[ 10.500386] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 10.668836] PM: Starting manual resume from disk
[ 10.719042] kjournald starting. Commit interval 5 seconds
[ 10.720825] EXT3-fs: mounted filesystem with ordered data mode.
[ 12.225238] udevd version 125 started
[ 13.014490] input: Power Button (FF) as /class/input/input4
[ 13.074767] ACPI: Power Button (FF) [PWRF]
[ 13.074929] input: Power Button (CM) as /class/input/input5
[ 13.138537] ACPI: Power Button (CM) [PWRB]
[ 13.435697] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 13.435697] iTCO_wdt: Found a ICH8 or ICH8R TCO device (Version=2, TCOBASE=0x0860)
[ 13.439733] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 13.518230] i801_smbus 0000:00:1f.3: enabling device (0001 -> 0003)
[ 13.518282] ACPI: PCI Interrupt 0000:00:1f.3[C] -> GSI 18 (level, low) -> IRQ 18
[ 13.582076] input: PC Speaker as /class/input/input6
[ 13.842229] input: ImExPS/2 Generic Explorer Mouse as /class/input/input7
[ 14.043097] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 14.043097] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 14.081424] hda_codec: Unknown model for AD1988, trying auto-probe from BIOS...
[ 16.153773] EXT3 FS on dm-1, internal journal
[ 16.906340] loop: module loaded
[ 19.404622] kjournald starting. Commit interval 5 seconds
[ 19.405270] EXT3 FS on dm-2, internal journal
[ 19.405345] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.459961] kjournald starting. Commit interval 5 seconds
[ 19.459961] EXT3 FS on dm-4, internal journal
[ 19.459961] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.499877] kjournald starting. Commit interval 5 seconds
[ 19.499877] EXT3 FS on dm-3, internal journal
[ 19.499877] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.566182] kjournald starting. Commit interval 5 seconds
[ 19.567877] EXT3 FS on dm-5, internal journal
[ 19.567877] EXT3-fs: mounted filesystem with ordered data mode.
[ 19.614185] Adding 3145720k swap on /dev/mapper/vg00-swap. Priority:-1 extents:1 across:3145720k
[ 23.253386] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 23.273639] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 23.399962] skge eth1: enabling interface
[ 23.759246] NET: Registered protocol family 10
[ 23.759246] lo: Disabled Privacy Extensions
[ 23.759246] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.274427] RPC: Registered udp transport module.
[ 24.274427] RPC: Registered tcp transport module.
[ 24.703476] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 25.115416] skge eth1: Link is up at 100 Mbps, full duplex, flow control both
[ 25.115416] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 33.085531] pnp: the driver 'parport_pc' has been registered
[ 33.088259] lp: driver loaded but no devices found
[ 33.151956] ppdev: user-space parallel port driver
[ 34.948321] NET: Registered protocol family 5
[ 35.913049] eth1: no IPv6 routers present
[ 79.408867] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 79.430835] NFSD: starting 90-second grace period
[ 81.020090] warning: `ntpd' uses 32-bit capabilities (legacy support in use)
[ 82.317990] Bluetooth: Core ver 2.11
[ 82.317990] NET: Registered protocol family 31
[ 82.317990] Bluetooth: HCI device and connection manager initialized
[ 82.317990] Bluetooth: HCI socket layer initialized
[ 82.344865] Bluetooth: L2CAP ver 2.9
[ 82.344913] Bluetooth: L2CAP socket layer initialized
[ 82.470109] Bluetooth: RFCOMM socket layer initialized
[ 82.470109] Bluetooth: RFCOMM TTY layer initialized
[ 82.470109] Bluetooth: RFCOMM ver 1.8
[ 82.790427] r8169: eth2: link down
[ 82.791625] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 89.379356] mtrr: type mismatch for c0000000,4000000 old: write-back new: write-combining
[ 291.714672] CPU0 attaching NULL sched-domain.
[ 291.714680] CPU1 attaching NULL sched-domain.
[ 291.744891] CPU0 attaching sched-domain:
[ 291.744896] domain 0: span 0-1
[ 291.744901] groups: 0 1
[ 291.744908] domain 1: span 0-1
[ 291.744912] groups: 0-1
[ 291.744919] CPU1 attaching sched-domain:
[ 291.744922] domain 0: span 0-1
[ 291.744926] groups: 1 0
[ 291.744933] domain 1: span 0-1
[ 291.744938] groups: 0-1

** Loaded modules:
Module Size Used by
rfcomm 38176 2
l2cap 23936 9 rfcomm
bluetooth 57124 4 rfcomm,l2cap
appletalk 35344 20
battery 16904 0
ppdev 11656 0
parport_pc 31016 0
lp 14724 0
parport 41776 3 ppdev,parport_pc,lp
cpufreq_stats 9120 0
cpufreq_ondemand 11792 0
cpufreq_conservative 11784 0
nfsd 248360 17
auth_rpcgss 47520 1 nfsd
exportfs 8704 1 nfsd
nfs 251696 0
lockd 68560 2 nfsd,nfs
nfs_acl 7552 2 nfsd,nfs
sunrpc 197480 13 nfsd,auth_rpcgss,nfs,lockd,nfs_acl
ipv6 288328 46
ipt_MASQUERADE 7296 1
iptable_nat 9872 1
nf_nat 23192 2 ipt_MASQUERADE,iptable_nat
nf_conntrack_ipv4 19352 3 iptable_nat,nf_nat
nf_conntrack 71440 4 ipt_MASQUERADE,iptable_nat,nf_nat,nf_conntrack_ipv 4
ip_tables 21520 1 iptable_nat
x_tables 25224 3 ipt_MASQUERADE,iptable_nat,ip_tables
cpufreq_powersave 6400 2
cpufreq_userspace 8452 0
acpi_cpufreq 11792 0
freq_table 9344 3 cpufreq_stats,cpufreq_ondemand,acpi_cpufreq
sbp2 25356 0
loop 19468 0
snd_hda_intel 434904 0
snd_pcm_oss 41760 0
snd_mixer_oss 18816 1 snd_pcm_oss
snd_pcm 81672 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 7428 0
psmouse 42268 0
pcspkr 7040 0
serio_raw 9860 0
snd_seq_oss 33152 0
snd_seq_midi 11072 0
i2c_i801 13596 0
snd_rawmidi 26784 1 snd_seq_midi
i2c_core 27936 1 i2c_i801
snd_seq_midi_event 11904 2 snd_seq_oss,snd_seq_midi
snd_seq 54304 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
iTCO_wdt 15696 0
snd_timer 25744 2 snd_pcm,snd_seq
snd_seq_device 11668 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
snd 63688 9 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,sn d_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_de vice
soundcore 12064 1 snd
snd_page_alloc 13072 2 snd_hda_intel,snd_pcm
button 11680 0
intel_agp 31728 0
joydev 14848 0
evdev 14208 4
ext3 125072 5
jbd 51240 1 ext3
mbcache 12804 1 ext3
dm_mirror 20608 0
dm_log 13956 1 dm_mirror
dm_snapshot 19400 0
dm_mod 58864 16 dm_mirror,dm_log,dm_snapshot
raid1 24192 2
md_mod 80164 2 raid1
sd_mod 29376 6
ide_cd_mod 36360 0
cdrom 37928 1 ide_cd_mod
ata_piix 22660 4
usbhid 45792 0
hid 41792 1 usbhid
ff_memless 9224 1 usbhid
jmicron 6912 0 [permanent]
ata_generic 10116 0
ohci1394 32564 0
skge 41744 0
ieee1394 93816 2 sbp2,ohci1394
ahci 33036 0
r8169 31492 0
libata 165472 3 ata_piix,ata_generic,ahci
ide_pci_generic 9220 0 [permanent]
ehci_hcd 36108 0
scsi_mod 160760 3 sbp2,sd_mod,libata
ide_core 128284 3 ide_cd_mod,jmicron,ide_pci_generic
dock 14112 1 libata
uhci_hcd 25760 0
thermal 22688 0
processor 42304 2 acpi_cpufreq,thermal
fan 9352 0
thermal_sys 17728 3 thermal,processor,fan

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82P965/G965 Memory Controller Hub [8086:29a0] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:820b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: intel-agp

00:01.0 PCI bridge [0604]: Intel Corporation 82P965/G965 PCI Express Root Port [8086:29a1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fa800000-fe8fffff
Prefetchable memory behind bridge: 00000000bfe00000-00000000dfdfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:03.0 Communication controller [0780]: Intel Corporation 82P965/G965 HECI Controller [8086:29a4] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:820b]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at febffc00 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>

00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at dc00 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at e000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: Memory at febff800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD Audio Controller [8086:284b] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:821a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at febf8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Prefetchable memory behind bridge: 00000000dfe00000-00000000dfefffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.4 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI Express Port 5 [8086:2847] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: fe900000-fe9fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. P5B [1043:81ec]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at febff400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: 0000000088000000-00000000880fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:1f.0 ISA bridge [0601]: Intel Corporation 82801HB/HR (ICH8/R) LPC Interface Controller [8086:2810] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:821a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt

00:1f.2 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 4 port SATA IDE Controller [8086:2820] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:821a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at ec00 [size=8]
Region 1: I/O ports at e880 [size=4]
Region 2: I/O ports at e800 [size=8]
Region 3: I/O ports at e480 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: I/O ports at e080 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ide-pci-generic, ata_generic, ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus Controller [8086:283e] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:821a]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at 88100000 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

00:1f.5 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 2 port SATA IDE Controller [8086:2825] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:821a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at d400 [size=8]
Region 1: I/O ports at d080 [size=4]
Region 2: I/O ports at d000 [size=8]
Region 3: I/O ports at cc00 [size=4]
Region 4: I/O ports at c880 [size=16]
Region 5: I/O ports at c800 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
Kernel modules: ide-pci-generic, ata_generic, ata_piix

01:00.0 VGA compatible controller [0300]: nVidia Corporation NV44 [GeForce 6200 TurboCache(TM)] [10de:0161] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:81f2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: nvidiafb

02:00.0 SATA controller [0106]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:81e4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 5: Memory at fe9fe000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at fe9e0000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

02:00.1 IDE interface [0101]: JMicron Technologies, Inc. JMicron 20360/20363 AHCI Controller [197b:2363] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:81e4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at a880 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at a480 [size=4]
Region 4: I/O ports at a400 [size=16]
Capabilities: <access denied>
Kernel driver in use: JMicron IDE
Kernel modules: ide-pci-generic, jmicron, ata_generic

04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet [10ec:8169] (rev 10)
Subsystem: Netgear Device [1385:311a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at b800 [size=256]
Region 1: Memory at feaffc00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 88000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

04:03.0 FireWire (IEEE 1394) [0c00]: VIA Technologies, Inc. VT6306 Fire II IEEE 1394 OHCI Link Layer Controller [1106:3044] (rev c0) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:81fe]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at bc00 [size=128]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394

04:04.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller [11ab:4320] (rev 14)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus) [1043:811a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at feaf8000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at b400 [size=256]
Expansion ROM at 88020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: skge
Kernel modules: skge



-- System Information:
Debian Release: 5.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.26-1-amd64 (SMP w/2 CPU cores)
Locale: LANG=nl_NL.UTF-8, LC_CTYPE=nl_NL.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.26-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo

linux-image-2.6.26-1-amd64 recommends no packages.

Versions of packages linux-image-2.6.26-1-amd64 suggests:
ii lilo 1:22.8-7 LInux LOader - The Classic OS load
pn linux-doc-2.6.26 <none> (no description available)

-- debconf information:
linux-image-2.6.26-1-amd64/preinst/bootloader-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/old-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/old-system-map-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/overwriting-modules-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/lilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/prerm/removing-running-kernel-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/prerm/would-invalidate-boot-loader-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-test-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-1-amd64/postinst/old-dir-initrd-link-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/preinst/failed-to-move-modules-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/create-kimage-link-2.6.26-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-1-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-1-amd64/preinst/initrd-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/depmod-error-initrd-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/preinst/elilo-initrd-2.6.26-1-amd64: true
linux-image-2.6.26-1-amd64/postinst/bootloader-error-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/preinst/abort-install-2.6.26-1-amd64:
linux-image-2.6.26-1-amd64/postinst/depmod-error-2.6.26-1-amd64: false
linux-image-2.6.26-1-amd64/preinst/abort-overwrite-2.6.26-1-amd64:



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 
Old 03-21-2009, 03:16 PM
Bastian Blank
 
Default Bug#520645: linux-image-2.6.26-1-amd64: after update, system doesn't boot because lilo can't find boot device.

reassign 520645 lilo
thanks

On Sat, Mar 21, 2009 at 04:09:36PM +0100, Geert-Jan Hut wrote:
> I had this same problem direcly after upgrading to lenny, as I
> remember then it turned out that the major/minor node number that was
> used to identify the boot partition was wrong, i.e. pointed to the
> wrong partition. I use software disk mirroring with lvm2, the node
> numbers were from the wrong partition.

This device major and minor numbers are not stable. Its a bug in lilo to
convert them. Reassigning.

Bastian

--
There are always alternatives.
-- Spock, "The Galileo Seven", stardate 2822.3



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 

Thread Tools




All times are GMT. The time now is 03:04 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org