Package: linux-image-2.6.25-2-686
Version: 2.6.25-5
Severity: normal
Pressing the power button produces two acpi events most of the time.
This makes using the event for something like hibernate quite difficult.
I do not see any particular pattern in the behaviour. Pressing the
power button usually produces two events but sometimes only one is
produced.
-- Package-specific info:
** Version:
Linux version 2.6.25-2-686 (Debian 2.6.25-5) (waldi@debian.org) (gcc version 4.1.3 20080420 (prerelease) (Debian 4.1.2-22)) #1 SMP Thu Jun 12 16:26:30 UTC 2008
** Command line:
root=/dev/mapper/nc4010-root ro video=radeonfb
** Not tainted
** Kernel log:
[17910.246553] .max_vruntime : 0.000001
[17910.246555] .spread : 0.000000
[17910.246557] .spread0 : 0.000000
[17910.246559] .nr_running : 0
[17910.246561] .load : 0
[17910.246563] .nr_spread_over : 0
[17910.246564]
[17910.246565] cfs_rq
[17910.246567] .exec_clock : 0.000000
[17910.246569] .MIN_vruntime : 0.000001
[17910.246571] .min_vruntime : 3462698.548046
[17910.246573] .max_vruntime : 0.000001
[17910.246575] .spread : 0.000000
[17910.246577] .spread0 : 0.000000
[17910.246579] .nr_running : 0
[17910.246581] .load : 0
[17910.246583] .nr_spread_over : 0
[17910.246584]
[17910.246585] cfs_rq
[17910.246587] .exec_clock : 0.000000
[17910.246589] .MIN_vruntime : 0.000001
[17910.246591] .min_vruntime : 3462698.548046
[17910.246594] .max_vruntime : 0.000001
[17910.246596] .spread : 0.000000
[17910.246598] .spread0 : 0.000000
[17910.246600] .nr_running : 1
[17910.246601] .load : 1024
[17910.246603] .nr_spread_over : 0
[17910.246606]
[17910.246607] runnable tasks:
[17910.246608] task PID tree-key switches prio exec-runtime sum-exec sum-sleep
[17910.246610] ----------------------------------------------------------------------------------------------------------
[17910.246619] R s2disk 22175 2528841.509814 3575934 120 0 0 0.000000 0.000000 0.000000
[17910.246626]
[17910.246643] cifsd
[17910.246648]
[17910.246650] Restarting tasks ... done.
[17910.433877] input: Power Button (FF) as /class/input/input29
[17910.466845] ACPI: Power Button (FF) [PWRF]
[17910.468782] input: Sleep Button (CM) as /class/input/input30
[17910.494842] ACPI: Sleep Button (CM) [C13C]
[17910.496740] input: Lid Switch as /class/input/input31
[17910.507008] ACPI: Lid Switch [C13B]
[17910.528340] ACPI: PCI Interrupt 0000:00:12.2[C] -> Link [C0C6] -> GSI 10 (level, low) -> IRQ 10
[17910.530299] ehci_hcd 0000:00:12.2: EHCI Host Controller
[17910.530815] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 3
[17910.532699] ehci_hcd 0000:00:12.2: irq 10, io mem 0x98400000
[17910.546804] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17910.548817] usb usb3: configuration #1 chosen from 1 choice
[17910.550663] hub 3-0:1.0: USB hub found
[17910.550770] hub 3-0:1.0: 5 ports detected
[17910.654991] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[17910.656851] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[17910.658510] usb usb3: Product: EHCI Host Controller
[17910.658764] usb usb3: Manufacturer: Linux 2.6.25-2-686 ehci_hcd
[17910.660542] usb usb3: SerialNumber: 0000:00:12.2
[17911.998964] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[17911.999010] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[17911.999083] agpgart: Putting AGP V2 device at 0000:01:05.0 into 4x mode
[17920.195368] CIFS VFS: Unexpected lookup error -112
[18042.508246] tg3: eth0: Link is down.
[18044.797119] ADDRCONF(NETDEV_UP): eth0: link is not ready
[18053.843828] tg3: eth0: Link is up at 100 Mbps, full duplex.
[18053.843828] tg3: eth0: Flow control is on for TX and on for RX.
[18053.843828] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[18064.096826] eth0: no IPv6 routers present
[18592.691736] usb 3-3: new high speed USB device using ehci_hcd and address 2
[18592.796195] usb 3-3: configuration #1 chosen from 1 choice
[18592.797573] usb 3-3: New USB device found, idVendor=090c, idProduct=1000
[18592.797588] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[18592.797596] usb 3-3: Product: Flash Voyager
[18592.797602] usb 3-3: Manufacturer: Corsair
[18592.797608] usb 3-3: SerialNumber: A900000000012912
[18593.034311] Initializing USB Mass Storage driver...
[18593.037841] scsi0 : SCSI emulation for USB Mass Storage devices
[18593.038497] usbcore: registered new interface driver usb-storage
[18593.038509] USB Mass Storage support registered.
[18593.076928] usb-storage: device found at 2
[18593.076942] usb-storage: waiting for device to settle before scanning
[18598.051110] usb-storage: device scan complete
[18598.052751] scsi 0:0:0:0: Direct-Access Corsair Flash Voyager 1100 PQ: 0 ANSI: 0 CCS
[18598.174677] Driver 'sd' needs updating - please use bus_type methods
[18598.178991] sd 0:0:0:0: [sda] 15859712 512-byte hardware sectors (8120 MB)
[18598.179745] sd 0:0:0:0: [sda] Write Protect is off
[18598.179752] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[18598.179756] sd 0:0:0:0: [sda] Assuming drive cache: write through
[18598.182489] sd 0:0:0:0: [sda] 15859712 512-byte hardware sectors (8120 MB)
[18598.184921] sd 0:0:0:0: [sda] Write Protect is off
[18598.184929] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[18598.184933] sd 0:0:0:0: [sda] Assuming drive cache: write through
[18598.184937] sda: sda1
[18598.210786] sd 0:0:0:0: [sda] Attached SCSI removable disk
[18604.055184] usb 3-3: USB disconnect, address 2
[18608.571461] CIFS VFS: Unexpected lookup error -112
[21965.262362] tg3: eth0: Link is down.
[21967.686119] ADDRCONF(NETDEV_UP): eth0: link is not ready
[22096.413024] tg3: eth0: Link is up at 100 Mbps, full duplex.
[22096.413024] tg3: eth0: Flow control is on for TX and on for RX.
[22096.413024] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[22106.555693] eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
sd_mod 26072 0
usb_storage 76896 0
ehci_hcd 32620 0
button 8240 0
nls_utf8 2080 1
cifs 204148 1
nls_base 7268 2 nls_utf8,cifs
binfmt_misc 11144 1
radeon 113152 2
drm 72280 3 radeon
ppdev 8676 0
lp 11012 0
sbs 8544 0
sbshc 6784 1 sbs
acpi_cpufreq 9260 0
cpufreq_conservative 7432 0
cpufreq_ondemand 8428 1
cpufreq_userspace 3812 0
cpufreq_stats 5216 0
freq_table 4512 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
cpufreq_powersave 1856 0
ipv6 241956 22
loop 16708 0
joydev 11328 0
irtty_sir 6176 0
pcmcia 36044 0
sir_dev 13764 1 irtty_sir
firmware_class 9088 1 pcmcia
parport_pc 25860 1
irda 106200 1 sir_dev
parport 33868 3 ppdev,lp,parport_pc
crc_ccitt 2176 1 irda
rtc 14272 0
pcspkr 3136 0
snd_ali5451 21740 1
serio_raw 6532 0
snd_ac97_codec 91300 1 snd_ali5451
ac97_bus 1952 1 snd_ac97_codec
psmouse 35920 0
snd_pcm_oss 37824 0
snd_pcm 68228 3 snd_ali5451,snd_ac97_codec,snd_pcm_oss
snd_mixer_oss 14880 1 snd_pcm_oss
snd_seq_dummy 3780 0
container 4736 0
snd_seq_oss 28544 0
snd_seq_midi 8064 0
video 19728 0
output 3712 1 video
snd_rawmidi 22528 1 snd_seq_midi
snd_seq_midi_event 6976 2 snd_seq_oss,snd_seq_midi
snd_seq 45872 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event
i2c_ali15x3 7492 0
i2c_ali1535 6788 0
wmi 7880 0
snd_timer 21320 2 snd_pcm,snd_seq
snd_seq_device 7564 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq
battery 8448 0
snd 48772 12 snd_ali5451,snd_ac97_codec,snd_pcm_oss,snd_pcm,snd _mixer_oss,snd_seq_oss,snd_rawmidi,snd_seq,snd_tim er,snd_seq_device
ac 4448 0
soundcore 7488 1 snd
snd_page_alloc 9992 1 snd_pcm
yenta_socket 24300 2
rsrc_nonstatic 11584 1 yenta_socket
pcmcia_core 36436 3 pcmcia,yenta_socket,rsrc_nonstatic
ati_agp 8524 1
shpchp 29716 0
pci_hotplug 26980 1 shpchp
agpgart 31720 2 drm,ati_agp
evdev 11328 6
ext3 120360 3
jbd 43444 1 ext3
mbcache 8260 1 ext3
dm_mirror 25316 0
dm_snapshot 17444 0
dm_mod 55656 9 dm_mirror,dm_snapshot
ide_disk 13952 3
ata_generic 8004 0
libata 142288 1 ata_generic
scsi_mod 138508 3 sd_mod,usb_storage,libata
dock 10448 1 libata
ide_pci_generic 4228 0 [permanent]
ohci_hcd 21668 0
tg3 89316 0
usbcore 130032 4 usb_storage,ehci_hcd,ohci_hcd
alim15x3 10156 0 [permanent]
ide_core 100312 3 ide_disk,ide_pci_generic,alim15x3
thermal 19100 0
processor 39660 3 acpi_cpufreq,thermal
fan 5636 0
radeonfb 96640 1
fb_ddc 2624 1 radeonfb
i2c_algo_bit 5892 1 radeonfb
i2c_core 22548 5 i2c_ali15x3,i2c_ali1535,radeonfb,fb_ddc,i2c_algo_b it
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS200/RS200M AGP Bridge [IGP 340M] [1002:cbb2] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: Memory at 9c000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at 98480000 (32-bit, prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: agpgart-ati
Kernel modules: ati-agp
00:01.0 PCI bridge [0604]: ATI Technologies Inc PCI Bridge [IGP 340M] [1002:7010]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=66
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 90000000-900fffff
Prefetchable memory behind bridge: 94000000-97ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:06.0 Multimedia audio controller [0401]: ALi Corporation M5451 PCI AC-Link Controller Audio Device [10b9:5451] (rev 02)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR+ <PERR+ INTx-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at 98080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ALI 5451
Kernel modules: trident, snd-ali5451
00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA Bridge [Aladdin IV/V/V+] [10b9:1533]
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: alim7101_wdt, alim1535_wdt
00:08.0 Modem [0703]: ALi Corporation M5457 AC'97 Modem Controller [10b9:5457]
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 98100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 3400 [size=256]
Capabilities: <access denied>
00:0b.0 CardBus bridge [0607]: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus Controller [1217:7114] (rev 20)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 98180000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 20000000-23fff000 (prefetchable)
Memory window 1: 24000000-27fff000
I/O window 0: 00001800-000018ff
I/O window 1: 00001c00-00001cff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
00:0b.1 CardBus bridge [0607]: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus Controller [1217:7114] (rev 20)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 98200000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
Memory window 0: 28000000-2bfff000 (prefetchable)
Memory window 1: 2c000000-2ffff000
I/O window 0: 00003c00-00003cff
I/O window 1: 00004000-000040ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
00:0b.2 System peripheral [0880]: O2 Micro, Inc. OZ711Mx 4-in-1 MemoryCardBus Accelerator [1217:7110]
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 98280000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:10.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229] (rev c4) (prog-if ea)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
Region 4: I/O ports at 3800 [size=16]
Capabilities: <access denied>
Kernel driver in use: ALI15x3_IDE
Kernel modules: alim15x3
00:11.0 Bridge [0680]: ALi Corporation M7101 Power Management Controller [PMU] [10b9:7101]
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: ali1535_smbus
Kernel modules: alim7101_wdt, i2c-ali15x3, i2c-ali1535
00:12.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 98300000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:12.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 43) (prog-if 10)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 98380000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:12.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 04) (prog-if 20)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 10
Region 0: Memory at 98400000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:13.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet [14e4:165d] (rev 03)
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 98000000 (64-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 30000000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
Kernel modules: tg3
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon IGP 330M/340M/350M [1002:4337]
Subsystem: Compaq Computer Corporation Device [0e11:005a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 94000000 (32-bit, prefetchable) [size=64M]
Region 1: I/O ports at 2000 [size=256]
Region 2: Memory at 90000000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at 90020000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: radeonfb
Kernel modules: radeonfb
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (990, 'testing'), (300, 'unstable'), (100, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.25-2-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.25-2-686 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92b tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.25-2-686 recommends:
ii libc6-i686 2.7-10 GNU C Library: Shared libraries [i
-- debconf information excluded
--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Bug#488799: linux-image-2.6.25-2-686: power button produces multiple events
