FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian Kernel

 
 
LinkBack Thread Tools
 
Old 06-29-2008, 08:18 AM
Alex Samad
 
Default Bug#488475: linux-image-2.6.25-2-amd64: r8196 driver having problems with GA-MA78GM-S2H motherboard

Package: linux-image-2.6.25-2-amd64
Version: 2.6.25-5
Severity: normal

I recently bought a gigabyte GA-MA78GM-S2H motherboard, comes with a Realtek 8111C chip nic.

I have installed debian (amd64) and I notice when I use ifconfig

eth0 Link encap:Ethernet HWaddr 00:1f:d0:59:14:a1
inet addr:192.168.11.14 Bcast:192.168.11.255 Mask:255.255.255.0
inet6 addr: fe80::21f:d0ff:fe59:14a1/64 Scope:Link
inet6 addr: 2002:3cf1:f856:11::14/64 Scope:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3402942 errors:0 dropped:14350521468 overruns:0 frame:0
TX packets:5908346 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:366689574 (349.7 MiB) TX bytes:8389785209 (7.8 GiB)
Interrupt:253 Base address:0x4000

there is a large amount of dropped, I have checked this on a newly booted machine and the number seems to be in the >1B
mark. IPv4 seems to be working okay. But I use radvd, ipv6 autoconfig to configure ipv6. icmpv6 router advertisements
don't seem to be making it to the card. I see noting then I run tcpdump

lspci -s 0:2:0.0 -vx
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev
02)
Subsystem: Giga-byte Technology Device e000
Flags: bus master, fast devsel, latency 0, IRQ 1277
I/O ports at de00 [size=256]
Memory at fdaff000 (64-bit, prefetchable) [size=4K]
Memory at fdae0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fda00000 [disabled] [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable- Mask- TabSize=2
Capabilities: [d0] Vital Product Data <?>
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Virtual Channel <?>
Capabilities: [160] Device Serial Number 78-56-34-12-78-56-34-12
Kernel driver in use: r8169
Kernel modules: r8169
00: ec 10 68 81 07 04 10 00 02 00 00 02 10 00 00 00
10: 01 de 00 00 00 00 00 00 0c f0 af fd 00 00 00 00
20: 0c 00 ae fd 00 00 00 00 00 00 00 00 58 14 00 e0
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 00 00


there seems to be some talk on this thread http://ubuntuforums.org/showthread.php?t=671614 of a r8168 module, which I
can't find in the source tree ?

Alex



-- Package-specific info:
** Version:
Linux version 2.6.25-2-amd64 (Debian 2.6.25-5) (waldi@debian.org) (gcc version 4.1.3 20080420 (prerelease) (Debian 4.1.2-22)) #1 SMP Thu Jun 12 15:38:32 UTC 2008

** Command line:
root=/dev/md1 ro

** Not tainted

** Kernel log:
[ 8.900625] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 9.089804] kjournald starting. Commit interval 5 seconds
[ 9.089804] EXT3-fs: mounted filesystem with ordered data mode.
[ 10.554413] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 10.577719] shpchp: HPC vendor_id 1022 device_id 9602 ss_vid 0 ss_did 0
[ 10.577759] shpchp: shpc_init: cannot reserve MMIO region
[ 10.577819] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.589313] input: Power Button (FF) as /class/input/input2
[ 10.642091] ACPI: Power Button (FF) [PWRF]
[ 10.642195] input: Power Button (CM) as /class/input/input3
[ 10.706101] ACPI: Power Button (CM) [PWRB]
[ 10.706216] ACPI: WMI: Mapper loaded
[ 10.915700] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 10.947844] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 16
[ 10.911489] input: PC Speaker as /class/input/input4
[ 10.981415] hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
[ 11.013163] ACPI: PCI Interrupt 0000:01:05.1[b] -> GSI 19 (level, low) -> IRQ 19
[ 11.013259] PCI: Setting latency timer of device 0000:01:05.1 to 64
[ 12.468999] EXT3 FS on md1, internal journal
[ 13.481179] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.605721] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 14.052302] NET: Registered protocol family 10
[ 14.053022] lo: Disabled Privacy Extensions
[ 14.082283] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 14.363004] loop: module loaded
[ 14.523946] md: md2 stopped.
[ 14.697862] md: bind<sdb3>
[ 14.697969] md: bind<sdd1>
[ 14.698063] md: bind<sde1>
[ 14.698187] md: bind<sdc3>
[ 14.698295] md: bind<sda3>
[ 14.781757] raid5: device sda3 operational as raid disk 0
[ 14.781757] raid5: device sdc3 operational as raid disk 4
[ 14.781757] raid5: device sde1 operational as raid disk 3
[ 14.781757] raid5: device sdd1 operational as raid disk 2
[ 14.781757] raid5: device sdb3 operational as raid disk 1
[ 14.782347] raid5: allocated 5324kB for md2
[ 14.782383] raid5: raid level 5 set md2 active with 5 out of 5 devices, algorithm 2
[ 14.782421] RAID5 conf printout:
[ 14.782455] --- rd:5 wd:5
[ 14.782488] disk 0, o:1, dev:sda3
[ 14.782522] disk 1, o:1, dev:sdb3
[ 14.782556] disk 2, o:1, dev:sdd1
[ 14.782591] disk 3, o:1, dev:sde1
[ 14.782625] disk 4, o:1, dev:sdc3
[ 15.870267] fuse init (API version 7.9)
[ 15.816388] kjournald starting. Commit interval 5 seconds
[ 16.099149] EXT3 FS on dm-13, internal journal
[ 16.099154] EXT3-fs: mounted filesystem with ordered data mode.
[ 16.137077] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 16.137796] SGI XFS Quota Management subsystem
[ 16.138495] Filesystem "dm-11": Disabling barriers, not supported by the underlying device
[ 16.163120] XFS mounting filesystem dm-11
[ 16.407644] Ending clean XFS mount for filesystem: dm-11
[ 16.407764] Filesystem "dm-16": Disabling barriers, not supported by the underlying device
[ 16.469163] XFS mounting filesystem dm-16
[ 16.990934] Ending clean XFS mount for filesystem: dm-16
[ 17.049294] Filesystem "dm-12": Disabling barriers, not supported by the underlying device
[ 17.055198] XFS mounting filesystem dm-12
[ 17.280384] Ending clean XFS mount for filesystem: dm-12
[ 17.280507] Filesystem "dm-3": Disabling barriers, not supported by the underlying device
[ 17.312545] XFS mounting filesystem dm-3
[ 17.534507] Ending clean XFS mount for filesystem: dm-3
[ 17.534624] Filesystem "dm-7": Disabling barriers, not supported by the underlying device
[ 17.579465] XFS mounting filesystem dm-7
[ 17.687882] Ending clean XFS mount for filesystem: dm-7
[ 18.122051] Adding 4194296k swap on /dev/mapper/raid5-swap. Priority:-1 extents:1 across:4194296k
[ 19.105986] r8169: eth0: link up
[ 19.105993] r8169: eth0: link up
[ 23.304870] RPC: Registered udp transport module.
[ 23.304875] RPC: Registered tcp transport module.
[ 23.361067] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 23.403091] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 23.423678] NFSD: starting 90-second grace period
[ 24.455759] device eth0 entered promiscuous mode
[ 25.090891] device eth0 left promiscuous mode
[ 30.455894] eth0: no IPv6 routers present
[ 154.468323] ACPI: PCI interrupt for device 0000:02:00.0 disabled
[ 291.769179] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 291.769200] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 291.770016] eth0: RTL8168c/8111c at 0xffffc20000634000, 00:1f:d0:59:14:a1, XID 3c4000c0 IRQ 1277
[ 291.771715] r8169: eth0: TBI auto-negotiating
[ 292.576303] r8169: eth0: link down
[ 292.576321] r8169: eth0: link down
[ 292.577148] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 295.035075] r8169: eth0: link up
[ 295.354959] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 304.958908] eth0: no IPv6 routers present
[ 1065.540689] ACPI: PCI interrupt for device 0000:02:00.0 disabled
[ 1148.681786] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 18
[ 1148.681806] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 1148.682663] eth0: RTL8168c/8111c at 0xffffc20000634000, 00:1f:d0:59:14:a1, XID 3c4000c0 IRQ 1277
[ 1148.684384] r8169: eth0: TBI auto-negotiating
[ 1148.707835] r8169: eth0: link down
[ 1150.848701] r8169: eth0: link down
[ 1148.708500] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1153.384112] r8169: eth0: link up
[ 1153.644106] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1164.464446] eth0: no IPv6 routers present
[173865.110735] process `sysctl' is using deprecated sysctl (syscall) net.ipv6.neigh.default.retrans_time; Use net.ipv6.neigh.default.retrans_time_ms instead.

** Loaded modules:
Module Size Used by
r8169 36868 0
nfsd 261032 63
lockd 73904 2 nfsd
nfs_acl 8192 1 nfsd
auth_rpcgss 52512 1 nfsd
sunrpc 206984 79 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 9472 1 nfsd
video 27412 0
output 8704 1 video
ac 9344 0
battery 14208 0
xfs 492968 5
ext2 76304 2
fuse 53440 3
loop 23044 0
firewire_sbp2 22808 0
ip6table_mangle 7936 1
ip6t_REJECT 9856 3
ip6t_LOG 11140 3
nf_conntrack_ipv6 22888 40
ip6table_filter 8064 1
ip6_tables 27024 3 ip6table_mangle,ip6t_LOG,ip6table_filter
ipv6 294120 25 ip6table_mangle,ip6t_REJECT,nf_conntrack_ipv6
iptable_mangle 8064 1
iptable_nat 12048 1
nf_nat 25624 1 iptable_nat
xt_limit 7684 27
ipt_REJECT 8576 4
ipt_ULOG 15784 3
xt_pkttype 6528 1
xt_tcpudp 7936 96
nf_conntrack_ipv4 23696 55 iptable_nat,nf_nat
xt_state 7040 92
nf_conntrack 76304 5 nf_conntrack_ipv6,iptable_nat,nf_nat,nf_conntrack_ ipv4,xt_state
iptable_filter 8192 1
ip_tables 25488 3 iptable_mangle,iptable_nat,iptable_filter
x_tables 28168 11 ip6t_REJECT,ip6t_LOG,ip6_tables,iptable_nat,xt_lim it,ipt_REJECT,ipt_ULOG,xt_pkttype,xt_tcpudp,xt_sta te,ip_tables
pcspkr 7808 0
k8temp 10624 0
snd_hda_intel 414296 0
i2c_piix4 14476 0
snd_pcm 88072 1 snd_hda_intel
snd_timer 29328 1 snd_pcm
i2c_core 30752 1 i2c_piix4
snd 66888 3 snd_hda_intel,snd_pcm,snd_timer
soundcore 13088 1 snd
snd_page_alloc 15120 2 snd_hda_intel,snd_pcm
wmi 13120 0
button 13856 0
shpchp 38300 0
pci_hotplug 35512 1 shpchp
evdev 17408 0
ext3 139408 2
jbd 55336 1 ext3
mbcache 13956 2 ext2,ext3
dm_mirror 31748 2
dm_snapshot 22472 0
dm_mod 68536 38 dm_mirror,dm_snapshot
raid456 129824 1
async_xor 7424 1 raid456
async_memcpy 6400 1 raid456
async_tx 7168 1 raid456
xor 10128 2 raid456,async_xor
raid1 28032 2
md_mod 87204 5 raid456,raid1
sd_mod 33728 22
ata_generic 13572 0
ide_pci_generic 9476 0 [permanent]
firewire_ohci 27908 0
firewire_core 45920 2 firewire_sbp2,firewire_ohci
crc_itu_t 6656 1 firewire_core
atiixp 8836 0 [permanent]
ide_core 138160 2 ide_pci_generic,atiixp
ehci_hcd 40076 0
ahci 36616 16
libata 166064 2 ata_generic,ahci
scsi_mod 170360 3 firewire_sbp2,sd_mod,libata
ohci_hcd 28292 0
dock 16288 1 libata
thermal 26656 0
processor 49388 1 thermal
fan 10760 0

** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600]
Subsystem: Advanced Micro Devices [AMD] RS780 Host Bridge [1022:9600]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Region 3: Memory at <ignored> (64-bit, non-prefetchable)

00:01.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx) [1022:9602]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fde00000-fdffffff
Prefetchable memory behind bridge: 00000000d8000000-00000000dfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp

00:0a.0 PCI bridge [0604]: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 5) [1022:9609]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fdd00000-fddfffff
Prefetchable memory behind bridge: 00000000fda00000-00000000fdafffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:11.0 SATA controller [0106]: ATI Technologies Inc SB700/SB800 SATA Controller [AHCI mode] [1002:4391] (prog-if 01)
Subsystem: Giga-byte Technology Device [1458:b002]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 1278
Region 0: I/O ports at ff00 [size=8]
Region 1: I/O ports at fe00 [size=4]
Region 2: I/O ports at fd00 [size=8]
Region 3: I/O ports at fc00 [size=4]
Region 4: I/O ports at fb00 [size=16]
Region 5: Memory at fe02f000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci

00:12.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02e000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:12.1 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller [1002:4398] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe02d000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:12.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe02c000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:13.0 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI0 Controller [1002:4397] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02b000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.1 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI1 Controller [1002:4398] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe02a000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:13.2 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB EHCI Controller [1002:4396] (prog-if 20)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fe029000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:14.0 SMBus [0c05]: ATI Technologies Inc SBx00 SMBus Controller [1002:4385] (rev 3a)
Subsystem: Giga-byte Technology Device [1458:4385]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort- >SERR+ <PERR+ INTx-
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4

00:14.1 IDE interface [0101]: ATI Technologies Inc SB700/SB800 IDE Controller [1002:439c] (prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at fa00 [size=16]
Capabilities: <access denied>
Kernel driver in use: ATIIXP_IDE
Kernel modules: ata_generic, atiixp, ide-pci-generic

00:14.2 Audio device [0403]: ATI Technologies Inc SBx00 Azalia [1002:4383]
Subsystem: Giga-byte Technology Device [1458:a022]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin ? routed to IRQ 16
Region 0: Memory at fe024000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:14.3 ISA bridge [0601]: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Subsystem: ATI Technologies Inc SB700/SB800 LPC host controller [1002:439d]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0

00:14.4 PCI bridge [0604]: ATI Technologies Inc SBx00 PCI to PCI Bridge [1002:4384] (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fdc00000-fdcfffff
Prefetchable memory behind bridge: fdb00000-fdbfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:14.5 USB Controller [0c03]: ATI Technologies Inc SB700/SB800 USB OHCI2 Controller [1002:4399] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 4 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe028000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
Kernel modules: k8temp

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon HD 3200 Graphics [1002:9610]
Subsystem: Giga-byte Technology Device [1458:d000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at ee00 [size=256]
Region 2: Memory at fdfe0000 (32-bit, non-prefetchable) [size=64K]
Region 5: Memory at fde00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>

01:05.1 Audio device [0403]: ATI Technologies Inc RS780 Azalia controller [1002:960f]
Subsystem: ATI Technologies Inc RS780 Azalia controller [1002:960f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 4 bytes
Interrupt: pin B routed to IRQ 19
Region 0: Memory at fdffc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 02)
Subsystem: Giga-byte Technology Device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 1277
Region 0: I/O ports at de00 [size=256]
Region 2: Memory at fdaff000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at fdae0000 (64-bit, prefetchable) [size=64K]
[virtual] Expansion ROM at fda00000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169

03:0e.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at fdcff000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fdcf8000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
Kernel modules: firewire-ohci



-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable'), (100, 'unstable')
Architecture: amd64 (x86_64)

Kernel: Linux 2.6.25-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_AU.UTF-8, LC_CTYPE=en_AU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.25-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92b tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo

linux-image-2.6.25-2-amd64 recommends no packages.

-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.25-2-amd64/prerm/removing-running-kernel-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/abort-overwrite-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/old-initrd-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/create-kimage-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/failed-to-move-modules-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/abort-install-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.25-2-amd64/postinst/depmod-error-2.6.25-2-amd64: false
linux-image-2.6.25-2-amd64/postinst/bootloader-test-error-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/postinst/old-system-map-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/prerm/would-invalidate-boot-loader-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/overwriting-modules-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/depmod-error-initrd-2.6.25-2-amd64: false
linux-image-2.6.25-2-amd64/postinst/old-dir-initrd-link-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/elilo-initrd-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/postinst/bootloader-error-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/lilo-initrd-2.6.25-2-amd64: true
linux-image-2.6.25-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.25-2-amd64/preinst/initrd-2.6.25-2-amd64:
linux-image-2.6.25-2-amd64/preinst/bootloader-initrd-2.6.25-2-amd64: true



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 
Old 11-07-2008, 11:11 PM
Moritz Muehlenhoff
 
Default Bug#488475: linux-image-2.6.25-2-amd64: r8196 driver having problems with GA-MA78GM-S2H motherboard

On Sun, Jun 29, 2008 at 06:18:10PM +1000, Alex Samad wrote:
> Package: linux-image-2.6.25-2-amd64
> Version: 2.6.25-5
> Severity: normal
>
> I recently bought a gigabyte GA-MA78GM-S2H motherboard, comes with a Realtek 8111C chip nic.
>
> there is a large amount of dropped, I have checked this on a newly booted machine and the number seems to be in the >1B
> mark. IPv4 seems to be working okay. But I use radvd, ipv6 autoconfig to configure ipv6. icmpv6 router advertisements
> don't seem to be making it to the card. I see noting then I run tcpdump

There have been many changes on the r8169 driver in 2.6.26 and the 2.6.26.x stable series.
Does the problem still occur with the current Lenny kernel?

Cheers,
Moritz



--
To UNSUBSCRIBE, email to debian-kernel-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
 
Old 03-25-2009, 08:21 PM
Alex Samad
 
Default Bug#488475: linux-image-2.6.25-2-amd64: r8196 driver having problems with GA-MA78GM-S2H motherboard

On Sat, Nov 08, 2008 at 01:11:38AM +0100, Moritz Muehlenhoff wrote:
> On Sun, Jun 29, 2008 at 06:18:10PM +1000, Alex Samad wrote:
> > Package: linux-image-2.6.25-2-amd64
> > Version: 2.6.25-5
> > Severity: normal
> >
> > I recently bought a gigabyte GA-MA78GM-S2H motherboard, comes with a Realtek 8111C chip nic.
> >
> > there is a large amount of dropped, I have checked this on a newly booted machine and the number seems to be in the >1B
> > mark. IPv4 seems to be working okay. But I use radvd, ipv6 autoconfig to configure ipv6. icmpv6 router advertisements
> > don't seem to be making it to the card. I see noting then I run tcpdump
>
> There have been many changes on the r8169 driver in 2.6.26 and the 2.6.26.x stable series.
> Does the problem still occur with the current Lenny kernel?

seems to be fixed in .28

>
> Cheers,
> Moritz
>

--
"Give me a chance to be your president and America will be safer and stronger and better."

- George W. Bush
07/13/2004
Marquette, MI
 

Thread Tools




All times are GMT. The time now is 01:24 AM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org