FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > Debian > Debian ISP

 
 
LinkBack Thread Tools
 
Old 08-05-2010, 04:15 PM
mimo
 
Default veryPC, Seagate, raid - caught in the middle

I have a veryPC 1U server with 2 nodes which both had been running fine until I upgraded one node (it's 2 independent systems sharing one power supply) and replaced the two 250GB WD hard disks with 4x500GB Seagate Momentus 7200RPM ones.
I set up the 4 hds as linux software raid1 like this:
md0 : active raid1 sda1[0] sdb1[1]
979840 blocks [2/2] [UU]
md1 : active raid1 sda2[0] sdb2[1]
9767424 blocks [2/2] [UU]
md2 : active raid1 sda3[2] sdb3[1]
292969280 blocks [2/2] [UU]
md3 : active raid1 sda4[0] sdb4[1]
184667072 blocks [2/2] [UU]
md4 : active raid1 sdd1[0] sdc1[1]
488383936 blocks [2/2] [UU]

After a couple of days of heavy load one of the drives (sdd) stopped responding (exact error further down). I spoke to manufacturer and they said it's possible there's a problem with Seagate laptop drives and raid because Seagate are trying to force customers to buy their server class laptop drives. They also recommended switching the two drives around. So I tried that but same problem again (on the same physical drive - now sdc). Raid degraded, one disk not responding. So I replaced the failed disk with a new one. Everything was fine for a while (almost a month).
But today I take a look and notice that a different md is degraded - md2. According to the log .

Jul 23 11:36:27 mail kernel: [820409.884399] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
Jul 23 11:36:27 mail kernel: [820409.904232] ata1: hard resetting link
Jul 23 11:36:28 mail kernel: [820411.759521] ata1: SATA link down (SStatus 0 SControl 300)
Jul 23 11:36:28 mail kernel: [820411.765296] ata1: failed to recover some devices, retrying in 5 secs
Jul 23 11:36:33 mail kernel: [820418.544474] ata1: hard resetting link
Jul 23 11:36:34 mail kernel: [820419.340756] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul 23 11:36:34 mail kernel: [820419.391208] ata1.00: configured for UDMA/133
Jul 23 11:36:34 mail kernel: [820419.416029] ata1.00: configured for UDMA/133
Jul 23 11:36:34 mail kernel: [820419.417892] ata1: EH complete
Jul 23 11:36:34 mail kernel: [820419.421891] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
Jul 23 11:36:34 mail kernel: [820419.502810] sd 0:0:0:0: [sda] Write Protect is off
Jul 23 11:36:34 mail kernel: [820419.507921] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul 23 11:36:34 mail kernel: [820419.517547] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
Jul 23 11:36:34 mail kernel: [820419.525220] sd 0:0:0:0: [sda] Write Protect is off
Jul 23 11:36:34 mail kernel: [820419.526461] md: super_written gets error=-5, uptodate=0
Jul 23 11:36:34 mail kernel: [820419.526461] raid1: Operation continuing on 1 devices.

Previously, I remember (sadly don't have logs from June anymore) it was trying with 1.5 Gbps and then gave up. But funny thing is that the other md devices on the same disk are still there.

General question, should I change my partitioning to just have one partition per drive and do the rest with lvm?

But more importantly, has anyone seen anything similar before? I suspect the controller/motherboard by now as I've tested the drive that had failed in the machine quite heavily but it still hasn't failed.

Any comments welcome. Some more details of the system:

Thanks,

mimo

lsscsi
[0:0:0:0] disk ATA ST9500420AS 0002 /dev/sda
[1:0:0:0] disk ATA ST9500420AS 0002 /dev/sdb
[2:0:0:0] disk ATA ST9500420AS 0002 /dev/sdc
[3:0:0:0] disk ATA ST9500420AS 0002 /dev/sdd

lspci
00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90)
00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90)
00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90)
00:08.0 System peripheral: Intel Corporation 5100 Chipset DMA Engine (rev 90)
00:10.0 Host bridge: Intel Corporation 5100 Chipset FSB Registers (rev 90)
00:10.1 Host bridge: Intel Corporation 5100 Chipset FSB Registers (rev 90)
00:10.2 Host bridge: Intel Corporation 5100 Chipset FSB Registers (rev 90)
00:11.0 Host bridge: Intel Corporation 5100 Chipset Reserved Registers (rev 90)
00:13.0 Host bridge: Intel Corporation 5100 Chipset Reserved Registers (rev 90)
00:15.0 Host bridge: Intel Corporation 5100 Chipset DDR Channel 0 Registers (rev 90)
00:16.0 Host bridge: Intel Corporation 5100 Chipset DDR Channel 1 Registers (rev 90)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92)
00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
05:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
06:01.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)

dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-amd64 (Debian 2.6.26-24) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 20 20:16:30 UTC 2010
[ 0.000000] Command line: root=/dev/md1 ro console=tty0 console=ttyS0,115200n8 vga=normal com1=115200,8n1
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009bc00 (usable)
[ 0.000000] BIOS-e820: 000000000009bc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dff40000 (usable)
[ 0.000000] BIOS-e820: 00000000dff40000 - 00000000dff5a000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dff5a000 - 00000000dff5b000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dff5b000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000220000000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 155) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 917312) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used
[ 0.000000] max_pfn_mapped = 2228224
[ 0.000000] init_memory_mapping
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F6010, 0024 (r2 PTLTD )
[ 0.000000] ACPI: XSDT DFF523A0, 00BC (r1 SMCI SMCISLP2 6040000 LTP 0)
[ 0.000000] ACPI: FACP DFF5944E, 00F4 (r3 INTEL SANCLMNT 6040000 PTL 3)
[ 0.000000] ACPI: DSDT DFF53F2E, 549C (r1 Intel SANCLMNT 6040000 MSFT 3000001)
[ 0.000000] ACPI: FACS DFF5AFC0, 0040
[ 0.000000] ACPI: APIC DFF59542, 00BC (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: MCFG DFF595FE, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: BOOT DFF5963A, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SPCR DFF59662, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1)
[ 0.000000] ACPI: ERST DFF596B2, 0590 (r1 SMCI ERSTTBL 6040000 SMCI 1)
[ 0.000000] ACPI: HEST DFF59C42, 00A8 (r1 SMCI HESTTBL 6040000 SMCI 1)
[ 0.000000] ACPI: BERT DFF59CEA, 0030 (r1 SMCI BERTTBL 6040000 SMCI 1)
[ 0.000000] ACPI: EINJ DFF59D1A, 0170 (r1 SMCI EINJTBL 6040000 SMCI 1)
[ 0.000000] ACPI: SLIC DFF59E8A, 0176 (r1 SMCI SMCISLP2 6040000 LTP 0)
[ 0.000000] ACPI: SSDT DFF53CCF, 025F (r1 PmRef Cpu0Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53C29, 00A6 (r1 PmRef Cpu7Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53B83, 00A6 (r1 PmRef Cpu6Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53ADD, 00A6 (r1 PmRef Cpu5Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53A37, 00A6 (r1 PmRef Cpu4Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53991, 00A6 (r1 PmRef Cpu3Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF538EB, 00A6 (r1 PmRef Cpu2Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53845, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF5245C, 13E9 (r1 PmRef CpuPm 3000 INTL 20080729)
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000220000000
[ 0.000000] Entering add_active_range(0, 0, 155) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 917312) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000220000000
[ 0.000000] NODE_DATA [0000000000012000 - 0000000000016fff]
[ 0.000000] bootmap [0000000000017000 - 000000000005afff] pages 44
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE
[ 0.000000] early res: 2 [200000-675397] TEXT DATA BSS
[ 0.000000] early res: 3 [37882000-37fefc15] RAMDISK
[ 0.000000] early res: 4 [9bc00-fffff] BIOS reserved
[ 0.000000] early res: 5 [8000-11fff] PGTABLE
[ 0.000000] [ffffe20000000000-ffffe20002dfffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0
[ 0.000000] [ffffe20002e00000-ffffe200077fffff] PMD -> [ffff81000c000000-ffff8100103fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 2228224
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 155
[ 0.000000] 0: 256 -> 917312
[ 0.000000] 0: 1048576 -> 2228224
[ 0.000000] On node 0 totalpages: 2096859
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1256 pages reserved
[ 0.000000] DMA zone: 2683 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 898936 pages, LIFO batch:31
[ 0.000000] Normal zone: 16128 pages used for memmap
[ 0.000000] Normal zone: 1163520 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] PM: Registered nosave memory: 000000000009b000 - 000000000009c000
[ 0.000000] PM: Registered nosave memory: 000000000009c000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
[ 0.000000] PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dff40000 - 00000000dff5a000
[ 0.000000] PM: Registered nosave memory: 00000000dff5a000 - 00000000dff5b000
[ 0.000000] PM: Registered nosave memory: 00000000dff5b000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
[ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at f1000000 (gap: f0000000:ec00000)
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37168 bytes of per cpu data
[ 0.000000] NR_CPUS: 32, nr_cpu_ids: 8
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2065139
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,115200n8 vga=normal com1=115200,8n1
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000000] time.c: Detected 2499.998 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] console [ttyS0] enabled
[ 0.004000] Checking aperture...
[ 0.004000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.004000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.004000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.004000] Placing software IO TLB between 0x4000000 - 0x8000000
[ 0.004000] Memory: 8191884k/8912896k available (2228k kernel code, 195552k reserved, 1084k data, 392k init)
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084017] Calibrating delay using timer specific routine.. 5004.05 BogoMIPS (lpj=10008106)
[ 0.092624] Security Framework initialized
[ 0.096789] SELinux: Disabled at boot.
[ 0.100688] Capability LSM initialized
[ 0.105104] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.115716] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.121703] Mount-cache hash table entries: 256
[ 0.126444] Initializing cgroup subsys ns
[ 0.130521] Initializing cgroup subsys cpuacct
[ 0.135027] Initializing cgroup subsys devices
[ 0.139552] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.144009] CPU: L2 cache: 6144K
[ 0.147298] CPU 0/0 -> Node 0
[ 0.150326] CPU: Physical Processor ID: 0
[ 0.154394] CPU: Processor Core ID: 0
[ 0.158120] CPU0: Thermal monitoring enabled (TM2)
[ 0.162971] using mwait in idle threads.
[ 0.167817] ACPI: Core revision 20080321
[ 0.226905] CPU0: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.234216] Using local APIC timer interrupts.
[ 0.244015] APIC timer calibration result 20833316
[ 0.244015] Detected 20.833 MHz APIC timer.
[ 0.248015] Booting processor 1/4 ip 6000
[ 0.260016] Initializing CPU#1
[ 0.260016] Calibrating delay using timer specific routine.. 16500.05 BogoMIPS (lpj=33000110)
[ 0.260016] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.260016] CPU: L2 cache: 6144K
[ 0.260016] CPU 1/4 -> Node 0
[ 0.260016] CPU: Physical Processor ID: 1
[ 0.260016] CPU: Processor Core ID: 0
[ 0.260016] CPU1: Thermal monitoring enabled (TM2)
[ 0.339718] CPU1: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.348021] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.352022] Booting processor 2/1 ip 6000
[ 0.368023] Initializing CPU#2
[ 0.368023] Calibrating delay using timer specific routine.. 5000.09 BogoMIPS (lpj=10000199)
[ 0.368023] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.368023] CPU: L2 cache: 6144K
[ 0.368023] CPU 2/1 -> Node 0
[ 0.368023] CPU: Physical Processor ID: 0
[ 0.368023] CPU: Processor Core ID: 1
[ 0.368023] CPU2: Thermal monitoring enabled (TM2)
[ 0.446604] CPU2: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.456028] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.460028] Booting processor 3/5 ip 6000
[ 0.476029] Initializing CPU#3
[ 0.476029] Calibrating delay using timer specific routine.. 5000.10 BogoMIPS (lpj=10000211)
[ 0.476029] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.476029] CPU: L2 cache: 6144K
[ 0.476029] CPU 3/5 -> Node 0
[ 0.476029] CPU: Physical Processor ID: 1
[ 0.476029] CPU: Processor Core ID: 1
[ 0.476029] CPU3: Thermal monitoring enabled (TM2)
[ 0.553917] CPU3: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.564031] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.568031] Booting processor 4/2 ip 6000
[ 0.584036] Initializing CPU#4
[ 0.584036] Calibrating delay using timer specific routine.. 5000.10 BogoMIPS (lpj=10000200)
[ 0.584036] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.584036] CPU: L2 cache: 6144K
[ 0.584036] CPU 4/2 -> Node 0
[ 0.584036] CPU: Physical Processor ID: 0
[ 0.584036] CPU: Processor Core ID: 2
[ 0.584036] CPU4: Thermal monitoring enabled (TM2)
[ 0.664716] CPU4: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.674091] checking TSC synchronization [CPU#0 -> CPU#4]: passed.
[ 0.678091] Booting processor 5/6 ip 6000
[ 0.692692] Initializing CPU#5
[ 0.692692] Calibrating delay using timer specific routine.. 5000.11 BogoMIPS (lpj=10000228)
[ 0.692692] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.692692] CPU: L2 cache: 6144K
[ 0.692692] CPU 5/6 -> Node 0
[ 0.692692] CPU: Physical Processor ID: 1
[ 0.692692] CPU: Processor Core ID: 2
[ 0.692692] CPU5: Thermal monitoring enabled (TM2)
[ 0.773393] CPU5: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.782706] checking TSC synchronization [CPU#0 -> CPU#5]: passed.
[ 0.786768] Booting processor 6/3 ip 6000
[ 0.801394] Initializing CPU#6
[ 0.801394] Calibrating delay using timer specific routine.. 5000.07 BogoMIPS (lpj=10000146)
[ 0.801394] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.801394] CPU: L2 cache: 6144K
[ 0.801394] CPU 6/3 -> Node 0
[ 0.801394] CPU: Physical Processor ID: 0
[ 0.801394] CPU: Processor Core ID: 3
[ 0.801394] CPU6: Thermal monitoring enabled (TM2)
[ 0.879553] CPU6: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.890706] checking TSC synchronization [CPU#0 -> CPU#6]: passed.
[ 0.894706] Booting processor 7/7 ip 6000
[ 0.909370] Initializing CPU#7
[ 0.909370] Calibrating delay using timer specific routine.. 5000.11 BogoMIPS (lpj=10000220)
[ 0.909370] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.909370] CPU: L2 cache: 6144K
[ 0.909370] CPU 7/7 -> Node 0
[ 0.909370] CPU: Physical Processor ID: 1
[ 0.909370] CPU: Processor Core ID: 3
[ 0.909370] CPU7: Thermal monitoring enabled (TM2)
[ 0.990078] CPU7: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.999413] checking TSC synchronization [CPU#0 -> CPU#7]: passed.
[ 1.003413] Brought up 8 CPUs
[ 1.006444] Total of 8 processors activated (51504.71 BogoMIPS).
[ 1.011413] CPU0 attaching sched-domain:
[ 1.011413] domain 0: span 0,2
[ 1.011413] groups: 0 2
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 0,2 1,3 4,6 5,7
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU1 attaching sched-domain:
[ 1.011413] domain 0: span 1,3
[ 1.011413] groups: 1 3
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 1,3 4,6 5,7 0,2
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU2 attaching sched-domain:
[ 1.011413] domain 0: span 0,2
[ 1.011413] groups: 2 0
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 0,2 1,3 4,6 5,7
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU3 attaching sched-domain:
[ 1.011413] domain 0: span 1,3
[ 1.011413] groups: 3 1
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 1,3 4,6 5,7 0,2
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU4 attaching sched-domain:
[ 1.011413] domain 0: span 4,6
[ 1.011413] groups: 4 6
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 4,6 5,7 0,2 1,3
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU5 attaching sched-domain:
[ 1.011413] domain 0: span 5,7
[ 1.011413] groups: 5 7
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 5,7 0,2 1,3 4,6
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU6 attaching sched-domain:
[ 1.011413] domain 0: span 4,6
[ 1.011413] groups: 6 4
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 4,6 5,7 0,2 1,3
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU7 attaching sched-domain:
[ 1.011413] domain 0: span 5,7
[ 1.011413] groups: 7 5
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 5,7 0,2 1,3 4,6
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] net_namespace: 1224 bytes
[ 1.015140] Booting paravirtualized kernel on bare hardware
[ 1.019413] NET: Registered protocol family 16
[ 1.023413] ACPI: bus type pci registered
[ 1.027413] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 5
[ 1.031413] PCI: MCFG area at e0000000 reserved in E820
[ 1.039387] PCI: Using MMCONFIG at e0000000 - e05fffff
[ 1.043387] PCI: Using configuration type 1 for base access
[ 1.047388] ACPI: EC: Look up EC in DSDT
[ 1.054290] ACPI: Interpreter enabled
[ 1.058009] ACPI: (supports S0 S1 S4 S5)
[ 1.062246] ACPI: Using IOAPIC for interrupt routing
[ 1.071602] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 1.075602] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 1.075602] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 1.079602] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 1.083602] PCI: Transparent bridge - 0000:00:1e.0
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP6._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 1.099569] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 1.103569] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 1.107569] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 1.115562] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 1.124433] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 1.128537] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 *10 11 14 15)
[ 1.132537] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 1.142736] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 *7 10 11 14 15)
[ 1.151796] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1.155797] pnp: PnP ACPI init
[ 1.155797] ACPI: bus type pnp registered
[ 1.159797] pnp 00:00: parse allocated resources
[ 1.163922] pnp 00:00: add io 0xcf8-0xcff flags 0x1
[ 1.167064] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 1.167064] pnp 00:01: parse allocated resources
[ 1.167064] pnp 00:01: add io 0x10-0x1f flags 0x1
[ 1.167064] pnp 00:01: add io 0x24-0x25 flags 0x1
[ 1.167064] pnp 00:01: add io 0x28-0x29 flags 0x1
[ 1.167064] pnp 00:01: add io 0x2c-0x2d flags 0x1
[ 1.167064] pnp 00:01: add io 0x2e-0x2f flags 0x1
[ 1.167064] pnp 00:01: add io 0x30-0x31 flags 0x1
[ 1.167064] pnp 00:01: add io 0x34-0x35 flags 0x1
[ 1.167064] pnp 00:01: add io 0x38-0x39 flags 0x1
[ 1.167064] pnp 00:01: add io 0x3c-0x3d flags 0x1
[ 1.167064] pnp 00:01: add io 0x4e-0x4f flags 0x1
[ 1.167064] pnp 00:01: add io 0x50-0x53 flags 0x1
[ 1.167064] pnp 00:01: add io 0x60-0x60 flags 0x1
[ 1.167064] pnp 00:01: add io 0x64-0x64 flags 0x1
[ 1.167064] pnp 00:01: add io 0x63-0x63 flags 0x1
[ 1.167064] pnp 00:01: add io 0x65-0x65 flags 0x1
[ 1.167064] pnp 00:01: add io 0x67-0x67 flags 0x1
[ 1.167064] pnp 00:01: add io 0x72-0x77 flags 0x1
[ 1.167064] pnp 00:01: add io 0x80-0x80 flags 0x1
[ 1.167064] pnp 00:01: add io 0x90-0x9f flags 0x1
[ 1.167064] pnp 00:01: add io 0xa4-0xa5 flags 0x1
[ 1.167064] pnp 00:01: add io 0xa8-0xa9 flags 0x1
[ 1.167064] pnp 00:01: add io 0xac-0xad flags 0x1
[ 1.167064] pnp 00:01: add io 0xb0-0xb5 flags 0x1
[ 1.167064] pnp 00:01: add io 0xb8-0xb9 flags 0x1
[ 1.167064] pnp 00:01: add io 0xbc-0xbd flags 0x1
[ 1.167064] pnp 00:01: add io 0x4d0-0x4d1 flags 0x1
[ 1.167064] pnp 00:01: add io 0x600-0x63f flags 0x1
[ 1.167064] pnp 00:01: add io 0x800-0x80f flags 0x1
[ 1.167064] pnp 00:01: add io 0xca0-0xcaf flags 0x1
[ 1.167064] pnp 00:01: add io 0x1000-0x107f flags 0x1
[ 1.167064] pnp 00:01: add io 0x1180-0x11bf flags 0x1
[ 1.167064] pnp 00:01: add io 0xfe00-0xfe00 flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfe600000-0xfe6fffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xe0000000-0xefffffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfed20000-0xfed3ffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfee00000-0xfee0ffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfef00000-0xfeffffff flags 0x1
[ 1.167064] pnp 00:01: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c
[ 1.167064] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.167064] pnp 00:02: parse allocated resources
[ 1.167064] pnp 00:02: add io 0x0-0xf flags 0x1
[ 1.167064] pnp 00:02: add io 0x81-0x8f flags 0x1
[ 1.167064] pnp 00:02: add io 0x93-0x9f flags 0x1
[ 1.167064] pnp 00:02: add io 0xc0-0xdf flags 0x1
[ 1.167064] pnp 00:02: add dma 4 flags 0x2
[ 1.167064] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.167064] pnp 00:03: parse allocated resources
[ 1.167064] pnp 00:03: add io 0xf0-0xfe flags 0x1
[ 1.167064] pnp 00:03: add irq 13 flags 0x1
[ 1.167064] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.167064] pnp 00:04: parse allocated resources
[ 1.167064] pnp 00:04: add io 0x70-0x71 flags 0x1
[ 1.167064] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.167064] pnp 00:05: parse allocated resources
[ 1.167064] pnp 00:05: add io 0x61-0x61 flags 0x1
[ 1.167064] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 1.167064] pnp 00:06: parse allocated resources
[ 1.167064] pnp 00:06: add mem 0xff800000-0xffffffff flags 0x1
[ 1.167064] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.167064] pnp 00:07: parse allocated resources
[ 1.167064] pnp 00:07: add io 0x3f8-0x3ff flags 0x1
[ 1.167064] pnp 00:07: add irq 4 flags 0x1
[ 1.167064] pnp 00:07: parse resource options
[ 1.167064] pnp 00:07: new independent option
[ 1.167064] pnp 00:07: new dependent option (priority 0x0)
[ 1.167064] pnp 00:07: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x1)
[ 1.167064] pnp 00:07: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x1)
[ 1.167064] pnp 00:07: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x1)
[ 1.167064] pnp 00:07: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: end dependent options
[ 1.167064] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.167064] pnp 00:08: parse allocated resources
[ 1.167064] pnp 00:08: add io 0x2f8-0x2ff flags 0x1
[ 1.167064] pnp 00:08: add irq 3 flags 0x1
[ 1.167064] pnp 00:08: parse resource options
[ 1.167064] pnp 00:08: new independent option
[ 1.167064] pnp 00:08: new dependent option (priority 0x1)
[ 1.167064] pnp 00:08: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x0)
[ 1.167064] pnp 00:08: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x1)
[ 1.167064] pnp 00:08: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x1)
[ 1.167064] pnp 00:08: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: end dependent options
[ 1.167064] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.167064] pnp: PnP ACPI: found 9 devices
[ 1.171065] ACPI: ACPI bus type pnp unregistered
[ 1.179064] usbcore: registered new interface driver usbfs
[ 1.183065] usbcore: registered new interface driver hub
[ 1.189197] usbcore: registered new device driver usb
[ 1.193197] PCI: Using ACPI for IRQ routing
[ 1.213179] PCI-GART: No AMD northbridge found.
[ 1.217857] hpet clockevent registered
[ 1.217861] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 1.225142] hpet0: 4 64-bit timers, 14318180 Hz
[ 1.229142] ACPI: RTC can wake from S4
[ 1.241272] pnp: the driver 'system' has been registered
[ 1.241280] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 1.245479] system 00:01: ioport range 0x600-0x63f has been reserved
[ 1.251883] system 00:01: ioport range 0x800-0x80f has been reserved
[ 1.258295] system 00:01: ioport range 0xca0-0xcaf has been reserved
[ 1.264708] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 1.271167] system 00:01: ioport range 0x1180-0x11bf has been reserved
[ 1.278056] system 00:01: ioport range 0xfe00-0xfe00 has been reserved
[ 1.284642] system 00:01: iomem range 0xfe600000-0xfe6fffff has been reserved
[ 1.291257] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 1.298460] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 1.306056] system 00:01: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 1.314056] system 00:01: iomem range 0xfef00000-0xfeffffff has been reserved
[ 1.321397] system 00:01: driver attached
[ 1.324992] PCI: Bridge: 0000:00:02.0
[ 1.328711] IO window: disabled.
[ 1.332172] MEM window: disabled.
[ 1.335719] PREFETCH window: disabled.
[ 1.339702] PCI: Bridge: 0000:00:04.0
[ 1.343420] IO window: disabled.
[ 1.346882] MEM window: disabled.
[ 1.350429] PREFETCH window: disabled.
[ 1.354412] PCI: Bridge: 0000:00:1c.0
[ 1.357403] IO window: disabled.
[ 1.361399] MEM window: disabled.
[ 1.365405] PREFETCH window: disabled.
[ 1.369407] PCI: Bridge: 0000:00:1c.4
[ 1.373404] IO window: 2000-2fff
[ 1.376972] MEM window: 0xf8000000-0xf80fffff
[ 1.381560] PREFETCH window: disabled.
[ 1.385541] PCI: Bridge: 0000:00:1c.5
[ 1.389406] IO window: 3000-3fff
[ 1.393407] MEM window: 0xf8100000-0xf81fffff
[ 1.397995] PREFETCH window: disabled.
[ 1.401976] PCI: Bridge: 0000:00:1e.0
[ 1.405692] IO window: 4000-4fff
[ 1.409407] MEM window: 0xf8200000-0xf82fffff
[ 1.413995] PREFETCH window: 0x00000000f0000000-0x00000000f7ffffff
[ 1.421410] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 1.421417] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.421434] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.429678] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.429691] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.437971] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 1.437988] ACPI: PCI Interrupt 0000:00:1c.5[b] -> GSI 17 (level, low) -> IRQ 17
[ 1.445529] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 1.445537] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 1.445597] NET: Registered protocol family 2
[ 1.489630] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 1.500262] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 1.510827] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.518028] TCP: Hash tables configured (established 524288 bind 65536)
[ 1.524711] TCP reno registered
[ 1.540100] NET: Registered protocol family 1
[ 1.544607] checking if image is initramfs...<7>Switched to high resolution mode on CPU 4
[ 1.772839] Switched to high resolution mode on CPU 7
[ 1.772836] Switched to high resolution mode on CPU 6
[ 1.772839] Switched to high resolution mode on CPU 3
[ 1.772836] Switched to high resolution mode on CPU 1
[ 1.772840] Switched to high resolution mode on CPU 2
[ 1.775175] Switched to high resolution mode on CPU 5
[ 1.775723] Switched to high resolution mode on CPU 0
[ 1.827168] it is
[ 2.059381] Freeing initrd memory: 7607k freed
[ 2.066770] Simple Boot Flag at 0x39 set to 0x1
[ 2.075236] audit: initializing netlink socket (disabled)
[ 2.081582] type=2000 audit(1281019578.036:1): initialized
[ 2.088575] Total HugeTLB memory allocated, 0
[ 2.093635] VFS: Disk quotas dquot_6.5.1
[ 2.095229] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.105808] msgmni has been set to 16014
[ 2.112242] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.119710] io scheduler noop registered
[ 2.123686] io scheduler anticipatory registered
[ 2.128359] io scheduler deadline registered
[ 2.132710] io scheduler cfq registered (default)
[ 2.137591] pci 0000:06:01.0: Boot video device
[ 2.139167] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 2.139167] assign_interrupt_mode Found MSI capability
[ 2.148703] Allocate Port Service[0000:00:02.0cie00]
[ 2.148759] Allocate Port Service[0000:00:02.0cie01]
[ 2.148841] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 2.148863] assign_interrupt_mode Found MSI capability
[ 2.155341] Allocate Port Service[0000:00:04.0cie00]
[ 2.156691] Allocate Port Service[0000:00:04.0cie01]
[ 2.156691] Allocate Port Service[0000:00:04.0cie02]
[ 2.156691] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 2.156691] assign_interrupt_mode Found MSI capability
[ 2.162561] Allocate Port Service[0000:00:1c.0cie00]
[ 2.163958] Allocate Port Service[0000:00:1c.0cie02]
[ 2.163958] Allocate Port Service[0000:00:1c.0cie03]
[ 2.163958] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 2.163958] assign_interrupt_mode Found MSI capability
[ 2.169177] Allocate Port Service[0000:00:1c.4cie00]
[ 2.169392] Allocate Port Service[0000:00:1c.4cie02]
[ 2.169392] Allocate Port Service[0000:00:1c.4cie03]
[ 2.169392] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 2.169392] assign_interrupt_mode Found MSI capability
[ 2.174549] Allocate Port Service[0000:00:1c.5cie00]
[ 2.175955] Allocate Port Service[0000:00:1c.5cie02]
[ 2.175955] Allocate Port Service[0000:00:1c.5cie03]
[ 2.175955] AER service couldn't init device 0000:00:02.0cie01 - no _OSC support
[ 2.175955] AER service couldn't init device 0000:00:04.0cie01 - no _OSC support
[ 2.180048] Linux agpgart interface v0.103
[ 2.184435] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.194434] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.200630] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.212065] pnp: the driver 'serial' has been registered
[ 2.212065] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.216059] serial 00:07: driver attached
[ 2.216059] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.224865] serial 00:08: driver attached
[ 2.224878] brd: module loaded
[ 2.231977] input: Macintosh mouse button emulation as /class/input/input0
[ 2.239799] pnp: the driver 'i8042 kbd' has been registered
[ 2.239799] pnp: the driver 'i8042 aux' has been registered
[ 2.239799] pnp: the driver 'i8042 kbd' has been unregistered
[ 2.239799] pnp: the driver 'i8042 aux' has been unregistered
[ 2.239799] PNP: No PS/2 controller found. Probing ports directly.
[ 2.246247] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.255905] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.279451] mice: PS/2 mouse device common for all mice
[ 2.284835] pnp: the driver 'rtc_cmos' has been registered
[ 2.284835] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 2.290998] rtc0: alarms up to one month, y3k
[ 2.295121] rtc_cmos 00:04: driver attached
[ 2.295554] cpuidle: using governor ladder
[ 2.299556] cpuidle: using governor menu
[ 2.303558] No iBFT detected.
[ 2.307448] TCP cubic registered
[ 2.309020] NET: Registered protocol family 17
[ 2.316146] registered taskstats version 1
[ 2.320469] rtc_cmos 00:04: setting system clock to 2010-08-05 14:46:20 UTC (1281019580)
[ 2.324785] Freeing unused kernel memory: 392k freed
[ 2.433843] ACPI: ACPI0007:00 is registered as cooling_device0
[ 2.437850] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.449843] ACPI: ACPI0007:01 is registered as cooling_device1
[ 2.456474] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.464133] ACPI: ACPI0007:02 is registered as cooling_device2
[ 2.468137] ACPI: Processor [CPU2] (supports 8 throttling states)
[ 2.480133] ACPI: ACPI0007:03 is registered as cooling_device3
[ 2.488472] ACPI: Processor [CPU3] (supports 8 throttling states)
[ 2.492471] ACPI: ACPI0007:04 is registered as cooling_device4
[ 2.502265] ACPI: Processor [CPU4] (supports 8 throttling states)
[ 2.508787] ACPI: ACPI0007:05 is registered as cooling_device5
[ 2.522254] ACPI: Processor [CPU5] (supports 8 throttling states)
[ 2.529355] ACPI: ACPI0007:06 is registered as cooling_device6
[ 2.540352] ACPI: Processor [CPU6] (supports 8 throttling states)
[ 2.549423] ACPI: ACPI0007:07 is registered as cooling_device7
[ 2.561415] ACPI: Processor [CPU7] (supports 8 throttling states)
[ 2.684347] USB Universal Host Controller Interface driver v3.0
[ 2.690633] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 2.698498] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 2.698501] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.704004] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.711697] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820
[ 2.718649] usb usb1: configuration #1 chosen from 1 choice
[ 2.724526] hub 1-0:1.0: USB hub found
[ 2.728489] hub 1-0:1.0: 2 ports detected
[ 2.742353] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
[ 2.748726] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 2.755095] No dock devices found.
[ 2.765457] SCSI subsystem initialized
[ 2.781067] libata version 3.00 loaded.
[ 2.845936] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.853930] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.861929] usb usb1: Product: UHCI Host Controller
[ 2.869935] usb usb1: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 2.877158] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.882773] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.902932] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.902935] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.910808] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.922588] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 2.974950] usb usb2: configuration #1 chosen from 1 choice
[ 2.980785] hub 2-0:1.0: USB hub found
[ 2.984770] hub 2-0:1.0: 2 ports detected
[ 3.105021] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.115618] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.172971] usb usb2: Product: UHCI Host Controller
[ 3.179398] usb usb2: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 3.185884] usb usb2: SerialNumber: 0000:00:1d.0
[ 3.255127] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 22 (level, low) -> IRQ 22
[ 3.260103] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 3.260106] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.335151] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 3.344610] uhci_hcd 0000:00:1d.1: irq 22, io base 0x00001860
[ 3.351170] usb usb3: configuration #1 chosen from 1 choice
[ 3.355117] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 3.365181] hub 3-0:1.0: USB hub found
[ 3.531142] hub 3-0:1.0: 2 ports detected
[ 3.661956] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.670347] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.678341] usb usb3: Product: UHCI Host Controller
[ 3.687123] usb usb3: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 3.721376] usb usb3: SerialNumber: 0000:00:1d.1
[ 3.763772] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 21
[ 3.770714] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.770717] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.775736] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.781373] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001880
[ 3.789387] usb usb4: configuration #1 chosen from 1 choice
[ 3.795893] usb 1-1: configuration #1 chosen from 1 choice
[ 3.835846] hub 4-0:1.0: USB hub found
[ 3.835846] usb 1-1: New USB device found, idVendor=14dd, idProduct=0002
[ 3.835846] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.835846] usb 1-1: Product: Multidevice
[ 3.835846] usb 1-1: Manufacturer: Peppercon AG
[ 3.835846] usb 1-1: SerialNumber: 0483ce0108495ed97CE4F555C62C01B7
[ 3.913577] hub 4-0:1.0: 2 ports detected
[ 4.022113] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.030101] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.040200] usb usb4: Product: UHCI Host Controller
[ 4.046106] usb usb4: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 4.054421] usb usb4: SerialNumber: 0000:00:1d.2
[ 4.070092] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) -> IRQ 22
[ 4.130906] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 4.130910] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 4.139616] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 5
[ 4.154409] ehci_hcd 0000:00:1a.7: debug port 1
[ 4.158414] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 4.158420] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xf8500800
[ 4.171071] usbcore: registered new interface driver hiddev
[ 4.186166] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.198229] usb usb5: configuration #1 chosen from 1 choice
[ 4.198160] usbcore: registered new interface driver usbhid
[ 4.198160] usbhid: v2.6:USB HID core driver
[ 4.214501] hub 5-0:1.0: USB hub found
[ 4.214522] usb 1-1: USB disconnect, address 2
[ 4.227315] hub 5-0:1.0: 2 ports detected
[ 4.336648] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.340398] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.364411] usb usb5: Product: EHCI Host Controller
[ 4.372412] usb usb5: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd
[ 4.377832] usb usb5: SerialNumber: 0000:00:1a.7
[ 4.385832] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 4.392881] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4.392884] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.398382] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 6
[ 4.409831] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.414872] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 4.414877] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8500c00
[ 4.434826] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.443162] usb usb6: configuration #1 chosen from 1 choice
[ 4.449838] hub 6-0:1.0: USB hub found
[ 4.456241] hub 6-0:1.0: 6 ports detected
[ 4.698671] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.706191] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.882605] usb usb6: Product: EHCI Host Controller
[ 4.890605] usb usb6: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd
[ 4.896029] usb usb6: SerialNumber: 0000:00:1d.7
[ 4.906590] ahci 0000:00:1f.2: version 3.0
[ 4.906590] ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 17 (level, low) -> IRQ 17
[ 5.022584] usb 5-1: new high speed USB device using ehci_hcd and address 2
[ 5.299422] usb 5-1: configuration #1 chosen from 1 choice
[ 5.311412] input: Peppercon AG Multidevice as /class/input/input1
[ 5.408436] input,hidraw0: USB HID v1.01 Mouse [Peppercon AG Multidevice] on usb-0000:00:1a.7-1
[ 5.421713] input: Peppercon AG Multidevice as /class/input/input2
[ 5.452938] input,hidraw1: USB HID v1.01 Keyboard [Peppercon AG Multidevice] on usb-0000:00:1a.7-1
[ 5.462526] usb 5-1: New USB device found, idVendor=14dd, idProduct=0002
[ 5.475770] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.483770] usb 5-1: Product: Multidevice
[ 5.490770] usb 5-1: Manufacturer: Peppercon AG
[ 5.495532] usb 5-1: SerialNumber: 0483ce0108495ed97CE4F555C62C01B7
[ 6.231839] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x2f impl SATA mode
[ 6.240380] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part
[ 6.295405] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 6.303409] scsi0 : ahci
[ 6.303409] scsi1 : ahci
[ 6.309134] scsi2 : ahci
[ 6.311879] scsi3 : ahci
[ 6.311880] scsi4 : ahci
[ 6.321088] scsi5 : ahci
[ 6.321176] ata1: SATA max UDMA/133 irq_stat 0x00400040, irq 1274
[ 6.334133] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
[ 6.342027] ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
[ 6.350029] ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
[ 6.357948] ata5: DUMMY
[ 6.401923] ata6: SATA max UDMA/133 abar m2048@0xf8500000 port 0xf8500380 irq 1274
[ 7.768943] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.828133] ata1.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 7.828306] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 7.853663] ata1.00: configured for UDMA/133
[ 8.762544] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8.810392] ata2.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 8.811202] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 8.835374] ata2.00: configured for UDMA/133
[ 10.142643] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 10.791190] ata3.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 10.797247] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 10.808351] ata3.00: configured for UDMA/133
[ 11.719811] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 11.986318] ata4.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 11.992473] ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 12.007553] ata4.00: configured for UDMA/133
[ 12.343300] ata6: SATA link down (SStatus 0 SControl 300)
[ 12.362120] scsi 0:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.827239] scsi 1:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.839447] scsi 2:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.848398] scsi 3:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.870240] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 12.892234] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 13.013765] eth0: (PCI Express:2.5GB/s:Width x1) 00:30:48:67:31:d6
[ 13.033485] eth0: Intel(R) PRO/1000 Network Connection
[ 13.041931] eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
[ 13.049756] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 13.054716] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 13.167083] eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:67:31:d7
[ 13.175228] eth1: Intel(R) PRO/1000 Network Connection
[ 13.181719] eth1: MAC: 2, PHY: 2, PBA No: ffffff-0ff
[ 13.256962] Driver 'sd' needs updating - please use bus_type methods
[ 13.264577] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 13.272490] sd 0:0:0:0: [sda] Write Protect is off
[ 13.277516] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.277547] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.289992] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 13.297934] sd 0:0:0:0: [sda] Write Protect is off
[ 13.305498] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.305519] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.317149] sda: sda1 sda2 sda3 sda4
[ 13.369515] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.401510] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 13.413077] sd 1:0:0:0: [sdb] Write Protect is off
[ 13.418545] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 13.418568] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.431417] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 13.439214] sd 1:0:0:0: [sdb] Write Protect is off
[ 13.444235] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 13.444253] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.454511] sdb: sdb1 sdb2 sdb3 sdb4
[ 13.520029] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 13.524904] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 13.611048] sd 2:0:0:0: [sdc] Write Protect is off
[ 13.616078] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 13.616096] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.628138] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 13.636083] sd 2:0:0:0: [sdc] Write Protect is off
[ 13.643586] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 13.643798] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.652740] sdc: sdc1
[ 13.701174] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 13.707722] sd 3:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[ 13.768291] sd 3:0:0:0: [sdd] Write Protect is off
[ 13.773340] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 13.773359] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.785372] sd 3:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[ 13.790825] sd 3:0:0:0: [sdd] Write Protect is off
[ 13.798279] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 13.798296] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.807300] sdd: sdd1
[ 13.842634] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 14.115107] md: raid1 personality registered for level 1
[ 14.131761] md: md0 stopped.
[ 14.214641] md: bind<sdb1>
[ 14.218650] md: bind<sda1>
[ 14.228571] raid1: raid set md0 active with 2 out of 2 mirrors
[ 14.236408] md: md1 stopped.
[ 14.334170] md: bind<sdb2>
[ 14.337088] md: bind<sda2>
[ 14.347529] raid1: raid set md1 active with 2 out of 2 mirrors
[ 14.355727] md: md2 stopped.
[ 14.505367] md: bind<sda3>
[ 14.508638] md: bind<sdb3>
[ 14.511706] md: kicking non-fresh sda3 from array!
[ 14.517039] md: unbind<sda3>
[ 14.521039] md: export_rdev(sda3)
[ 14.531597] raid1: raid set md2 active with 1 out of 2 mirrors
[ 14.551393] md: md3 stopped.
[ 14.605925] md: bind<sdb4>
[ 14.609925] md: bind<sda4>
[ 14.624698] raid1: raid set md3 active with 2 out of 2 mirrors
[ 14.631521] md: md4 stopped.
[ 14.669304] md: bind<sdc1>
[ 14.673275] md: bind<sdd1>
[ 14.683366] raid1: raid set md4 active with 2 out of 2 mirrors
[ 14.760828] device-mapper: uevent: version 1.0.3
[ 14.768951] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 14.847613] PM: Starting manual resume from disk
[ 14.885328] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 14.908660] SGI XFS Quota Management subsystem
[ 14.912661] Filesystem "md1": Disabling barriers, not supported by the underlying device
[ 14.920661] XFS mounting filesystem md1
[ 15.110893] Ending clean XFS mount for filesystem: md1
[ 17.438589] udevd version 125 started
[ 17.815323] input: Power Button (FF) as /class/input/input3
[ 17.842475] ACPI: Power Button (FF) [PWRF]
[ 17.852263] input: Power Button (CM) as /class/input/input4
[ 17.889629] ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 17 (level, low) -> IRQ 17
[ 17.901344] input: PC Speaker as /class/input/input5
[ 18.082676] ACPI: Power Button (CM) [PWRB]
[ 18.262564] Error: Driver 'pcspkr' is already registered, aborting...
[ 19.970509] Filesystem "md1": Disabling barriers, not supported by the underlying device
[ 21.025244] loop: module loaded
[ 21.054985] ipmi message handler version 39.2
[ 21.067961] IPMI System Interface driver.
[ 21.072957] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
[ 21.191106] ipmi: Found new BMC (man_id: 0x0028c5, prod_id: 0x0004, dev_id: 0x22)
[ 21.199105] IPMI kcs interface initialized
[ 21.296027] w83627hf: Found W83627HF chip at 0x290
[ 21.300353] w83627hf w83627hf.656: Enabling temp2, readings might not make sense
[ 21.308677] w83627hf w83627hf.656: Enabling temp3, readings might not make sense
[ 21.327912] coretemp coretemp.0: Using relative temperature scale!
[ 21.337977] coretemp coretemp.1: Using relative temperature scale!
[ 21.344852] coretemp coretemp.2: Using relative temperature scale!
[ 21.352840] coretemp coretemp.3: Using relative temperature scale!
[ 21.361047] coretemp coretemp.4: Using relative temperature scale!
[ 21.367940] coretemp coretemp.5: Using relative temperature scale!
[ 21.375939] coretemp coretemp.6: Using relative temperature scale!
[ 21.383942] coretemp coretemp.7: Using relative temperature scale!
[ 22.638207] kjournald starting. Commit interval 5 seconds
[ 22.647304] EXT3 FS on md0, internal journal
[ 22.651818] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.661520] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 22.673519] XFS mounting filesystem dm-0
[ 23.090546] Ending clean XFS mount for filesystem: dm-0
[ 23.098551] Filesystem "md2": Disabling barriers, not supported by the underlying device
[ 23.169293] XFS mounting filesystem md2
[ 23.444104] Ending clean XFS mount for filesystem: md2
[ 23.869974] Adding 87109624k swap on /dev/mapper/vg0-swapspare. Priority:-1 extents:1 across:87109624k


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 201008051715.49631.mimo@restoel.net">http://lists.debian.org/201008051715.49631.mimo@restoel.net
 
Old 08-06-2010, 06:49 AM
kalpesh thaker
 
Default veryPC, Seagate, raid - caught in the middle

Hi Mimo,

I have had similar issues to this. it happened some time back, however,
i had a raid 0 setup, of which data became

inconsistent very often...and i got endless array failures.

Naturally, i replaced the drives, after which the same issue happened
some weeks later. it took me a while to figure out
my problem, which in the end was a faulty SATA Raid backplane. Once i
had changed that, everything ran fine.


Depending on what type of machine you are using, id recommend trying
another backplane, or replacing the
SATA cables. If this machine is fairly old, i'd also recommend removing
the backplane and spraying the internal
and external connectors with compressed air to remove any dust that
sometimes settles there. Also, make sure that
your servers are well ventilated, and that the drives are not
overheating. If all else if fine, then i'd agree that

your motherboard might be faulty.

In my case of the 'faulty' drives, i was advised by our hardware
supplier to run a diagnostic on the drives,
using Seagate Seatools before sending them back for warranty
replacement. Ironically, Seatools had passed all
the drives on the extended tests, and to verify, the drives did actually
run fine in another machine.


LVM is an excellent idea for production servers, as when and if your
drives begin to fail, and you need to replace them
with bigger drives, you can grow the LVM partitions on the raid arrays
to the size of the bigger drives fairly easily.


regards

kalpesh.


On 05/08/2010 18:15, mimo wrote:

I have a veryPC 1U server with 2 nodes which both had been running fine until I upgraded one node (it's 2 independent systems sharing one power supply) and replaced the two 250GB WD hard disks with 4x500GB Seagate Momentus 7200RPM ones.
I set up the 4 hds as linux software raid1 like this:
md0 : active raid1 sda1[0] sdb1[1]
979840 blocks [2/2] [UU]
md1 : active raid1 sda2[0] sdb2[1]
9767424 blocks [2/2] [UU]
md2 : active raid1 sda3[2] sdb3[1]
292969280 blocks [2/2] [UU]
md3 : active raid1 sda4[0] sdb4[1]
184667072 blocks [2/2] [UU]
md4 : active raid1 sdd1[0] sdc1[1]
488383936 blocks [2/2] [UU]

After a couple of days of heavy load one of the drives (sdd) stopped responding (exact error further down). I spoke to manufacturer and they said it's possible there's a problem with Seagate laptop drives and raid because Seagate are trying to force customers to buy their server class laptop drives. They also recommended switching the two drives around. So I tried that but same problem again (on the same physical drive - now sdc). Raid degraded, one disk not responding. So I replaced the failed disk with a new one. Everything was fine for a while (almost a month).
But today I take a look and notice that a different md is degraded - md2. According to the log .

Jul 23 11:36:27 mail kernel: [820409.884399] res 40/00:00:00:4f:c2/00:00:00:00:00/40 Emask 0x4 (timeout)
Jul 23 11:36:27 mail kernel: [820409.904232] ata1: hard resetting link
Jul 23 11:36:28 mail kernel: [820411.759521] ata1: SATA link down (SStatus 0 SControl 300)
Jul 23 11:36:28 mail kernel: [820411.765296] ata1: failed to recover some devices, retrying in 5 secs
Jul 23 11:36:33 mail kernel: [820418.544474] ata1: hard resetting link
Jul 23 11:36:34 mail kernel: [820419.340756] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Jul 23 11:36:34 mail kernel: [820419.391208] ata1.00: configured for UDMA/133
Jul 23 11:36:34 mail kernel: [820419.416029] ata1.00: configured for UDMA/133
Jul 23 11:36:34 mail kernel: [820419.417892] ata1: EH complete
Jul 23 11:36:34 mail kernel: [820419.421891] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
Jul 23 11:36:34 mail kernel: [820419.502810] sd 0:0:0:0: [sda] Write Protect is off
Jul 23 11:36:34 mail kernel: [820419.507921] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Jul 23 11:36:34 mail kernel: [820419.517547] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
Jul 23 11:36:34 mail kernel: [820419.525220] sd 0:0:0:0: [sda] Write Protect is off
Jul 23 11:36:34 mail kernel: [820419.526461] md: super_written gets error=-5, uptodate=0
Jul 23 11:36:34 mail kernel: [820419.526461] raid1: Operation continuing on 1 devices.

Previously, I remember (sadly don't have logs from June anymore) it was trying with 1.5 Gbps and then gave up. But funny thing is that the other md devices on the same disk are still there.

General question, should I change my partitioning to just have one partition per drive and do the rest with lvm?

But more importantly, has anyone seen anything similar before? I suspect the controller/motherboard by now as I've tested the drive that had failed in the machine quite heavily but it still hasn't failed.

Any comments welcome. Some more details of the system:

Thanks,

mimo

lsscsi
[0:0:0:0] disk ATA ST9500420AS 0002 /dev/sda
[1:0:0:0] disk ATA ST9500420AS 0002 /dev/sdb
[2:0:0:0] disk ATA ST9500420AS 0002 /dev/sdc
[3:0:0:0] disk ATA ST9500420AS 0002 /dev/sdd

lspci
00:00.0 Host bridge: Intel Corporation 5100 Chipset Memory Controller Hub (rev 90)
00:02.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x8 Port 2-3 (rev 90)
00:04.0 PCI bridge: Intel Corporation 5100 Chipset PCI Express x16 Port 4-7 (rev 90)
00:08.0 System peripheral: Intel Corporation 5100 Chipset DMA Engine (rev 90)
00:10.0 Host bridge: Intel Corporation 5100 Chipset FSB Registers (rev 90)
00:10.1 Host bridge: Intel Corporation 5100 Chipset FSB Registers (rev 90)
00:10.2 Host bridge: Intel Corporation 5100 Chipset FSB Registers (rev 90)
00:11.0 Host bridge: Intel Corporation 5100 Chipset Reserved Registers (rev 90)
00:13.0 Host bridge: Intel Corporation 5100 Chipset Reserved Registers (rev 90)
00:15.0 Host bridge: Intel Corporation 5100 Chipset DDR Channel 0 Registers (rev 90)
00:16.0 Host bridge: Intel Corporation 5100 Chipset DDR Channel 1 Registers (rev 90)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02)
00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92)
00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA AHCI Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02)
04:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet Controller (Copper) (rev 03)
05:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
06:01.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)

dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.26-2-amd64 (Debian 2.6.26-24) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 20 20:16:30 UTC 2010
[ 0.000000] Command line: root=/dev/md1 ro console=tty0 console=ttyS0,115200n8 vga=normal com1=115200,8n1
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009bc00 (usable)
[ 0.000000] BIOS-e820: 000000000009bc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000dff40000 (usable)
[ 0.000000] BIOS-e820: 00000000dff40000 - 00000000dff5a000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000dff5a000 - 00000000dff5b000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000dff5b000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000220000000 (usable)
[ 0.000000] Entering add_active_range(0, 0, 155) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 917312) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used
[ 0.000000] max_pfn_mapped = 2228224
[ 0.000000] init_memory_mapping
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP 000F6010, 0024 (r2 PTLTD )
[ 0.000000] ACPI: XSDT DFF523A0, 00BC (r1 SMCI SMCISLP2 6040000 LTP 0)
[ 0.000000] ACPI: FACP DFF5944E, 00F4 (r3 INTEL SANCLMNT 6040000 PTL 3)
[ 0.000000] ACPI: DSDT DFF53F2E, 549C (r1 Intel SANCLMNT 6040000 MSFT 3000001)
[ 0.000000] ACPI: FACS DFF5AFC0, 0040
[ 0.000000] ACPI: APIC DFF59542, 00BC (r1 PTLTD APIC 6040000 LTP 0)
[ 0.000000] ACPI: MCFG DFF595FE, 003C (r1 PTLTD MCFG 6040000 LTP 0)
[ 0.000000] ACPI: BOOT DFF5963A, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SPCR DFF59662, 0050 (r1 PTLTD $UCRTBL$ 6040000 PTL 1)
[ 0.000000] ACPI: ERST DFF596B2, 0590 (r1 SMCI ERSTTBL 6040000 SMCI 1)
[ 0.000000] ACPI: HEST DFF59C42, 00A8 (r1 SMCI HESTTBL 6040000 SMCI 1)
[ 0.000000] ACPI: BERT DFF59CEA, 0030 (r1 SMCI BERTTBL 6040000 SMCI 1)
[ 0.000000] ACPI: EINJ DFF59D1A, 0170 (r1 SMCI EINJTBL 6040000 SMCI 1)
[ 0.000000] ACPI: SLIC DFF59E8A, 0176 (r1 SMCI SMCISLP2 6040000 LTP 0)
[ 0.000000] ACPI: SSDT DFF53CCF, 025F (r1 PmRef Cpu0Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53C29, 00A6 (r1 PmRef Cpu7Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53B83, 00A6 (r1 PmRef Cpu6Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53ADD, 00A6 (r1 PmRef Cpu5Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53A37, 00A6 (r1 PmRef Cpu4Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53991, 00A6 (r1 PmRef Cpu3Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF538EB, 00A6 (r1 PmRef Cpu2Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF53845, 00A6 (r1 PmRef Cpu1Tst 3000 INTL 20080729)
[ 0.000000] ACPI: SSDT DFF5245C, 13E9 (r1 PmRef CpuPm 3000 INTL 20080729)
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-0000000220000000
[ 0.000000] Entering add_active_range(0, 0, 155) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 917312) 1 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 1048576, 2228224) 2 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-0000000220000000
[ 0.000000] NODE_DATA [0000000000012000 - 0000000000016fff]
[ 0.000000] bootmap [0000000000017000 - 000000000005afff] pages 44
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] TRAMPOLINE
[ 0.000000] early res: 2 [200000-675397] TEXT DATA BSS
[ 0.000000] early res: 3 [37882000-37fefc15] RAMDISK
[ 0.000000] early res: 4 [9bc00-fffff] BIOS reserved
[ 0.000000] early res: 5 [8000-11fff] PGTABLE
[ 0.000000] [ffffe20000000000-ffffe20002dfffff] PMD -> [ffff810001200000-ffff810003ffffff] on node 0
[ 0.000000] [ffffe20002e00000-ffffe200077fffff] PMD -> [ffff81000c000000-ffff8100103fffff] on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 2228224
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0 -> 155
[ 0.000000] 0: 256 -> 917312
[ 0.000000] 0: 1048576 -> 2228224
[ 0.000000] On node 0 totalpages: 2096859
[ 0.000000] DMA zone: 56 pages used for memmap
[ 0.000000] DMA zone: 1256 pages reserved
[ 0.000000] DMA zone: 2683 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 14280 pages used for memmap
[ 0.000000] DMA32 zone: 898936 pages, LIFO batch:31
[ 0.000000] Normal zone: 16128 pages used for memmap
[ 0.000000] Normal zone: 1163520 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x04] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x06] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 0, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] PM: Registered nosave memory: 000000000009b000 - 000000000009c000
[ 0.000000] PM: Registered nosave memory: 000000000009c000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000ce000
[ 0.000000] PM: Registered nosave memory: 00000000000ce000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dff40000 - 00000000dff5a000
[ 0.000000] PM: Registered nosave memory: 00000000dff5a000 - 00000000dff5b000
[ 0.000000] PM: Registered nosave memory: 00000000dff5b000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ff000000
[ 0.000000] PM: Registered nosave memory: 00000000ff000000 - 0000000100000000
[ 0.000000] Allocating PCI resources starting at f1000000 (gap: f0000000:ec00000)
[ 0.000000] SMP: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37168 bytes of per cpu data
[ 0.000000] NR_CPUS: 32, nr_cpu_ids: 8
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2065139
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,115200n8 vga=normal com1=115200,8n1
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000000] time.c: Detected 2499.998 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] console [ttyS0] enabled
[ 0.004000] Checking aperture...
[ 0.004000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.004000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.004000] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.004000] Placing software IO TLB between 0x4000000 - 0x8000000
[ 0.004000] Memory: 8191884k/8912896k available (2228k kernel code, 195552k reserved, 1084k data, 392k init)
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.084017] Calibrating delay using timer specific routine.. 5004.05 BogoMIPS (lpj=10008106)
[ 0.092624] Security Framework initialized
[ 0.096789] SELinux: Disabled at boot.
[ 0.100688] Capability LSM initialized
[ 0.105104] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.115716] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.121703] Mount-cache hash table entries: 256
[ 0.126444] Initializing cgroup subsys ns
[ 0.130521] Initializing cgroup subsys cpuacct
[ 0.135027] Initializing cgroup subsys devices
[ 0.139552] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.144009] CPU: L2 cache: 6144K
[ 0.147298] CPU 0/0 -> Node 0
[ 0.150326] CPU: Physical Processor ID: 0
[ 0.154394] CPU: Processor Core ID: 0
[ 0.158120] CPU0: Thermal monitoring enabled (TM2)
[ 0.162971] using mwait in idle threads.
[ 0.167817] ACPI: Core revision 20080321
[ 0.226905] CPU0: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.234216] Using local APIC timer interrupts.
[ 0.244015] APIC timer calibration result 20833316
[ 0.244015] Detected 20.833 MHz APIC timer.
[ 0.248015] Booting processor 1/4 ip 6000
[ 0.260016] Initializing CPU#1
[ 0.260016] Calibrating delay using timer specific routine.. 16500.05 BogoMIPS (lpj=33000110)
[ 0.260016] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.260016] CPU: L2 cache: 6144K
[ 0.260016] CPU 1/4 -> Node 0
[ 0.260016] CPU: Physical Processor ID: 1
[ 0.260016] CPU: Processor Core ID: 0
[ 0.260016] CPU1: Thermal monitoring enabled (TM2)
[ 0.339718] CPU1: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.348021] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.352022] Booting processor 2/1 ip 6000
[ 0.368023] Initializing CPU#2
[ 0.368023] Calibrating delay using timer specific routine.. 5000.09 BogoMIPS (lpj=10000199)
[ 0.368023] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.368023] CPU: L2 cache: 6144K
[ 0.368023] CPU 2/1 -> Node 0
[ 0.368023] CPU: Physical Processor ID: 0
[ 0.368023] CPU: Processor Core ID: 1
[ 0.368023] CPU2: Thermal monitoring enabled (TM2)
[ 0.446604] CPU2: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.456028] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.460028] Booting processor 3/5 ip 6000
[ 0.476029] Initializing CPU#3
[ 0.476029] Calibrating delay using timer specific routine.. 5000.10 BogoMIPS (lpj=10000211)
[ 0.476029] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.476029] CPU: L2 cache: 6144K
[ 0.476029] CPU 3/5 -> Node 0
[ 0.476029] CPU: Physical Processor ID: 1
[ 0.476029] CPU: Processor Core ID: 1
[ 0.476029] CPU3: Thermal monitoring enabled (TM2)
[ 0.553917] CPU3: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.564031] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.568031] Booting processor 4/2 ip 6000
[ 0.584036] Initializing CPU#4
[ 0.584036] Calibrating delay using timer specific routine.. 5000.10 BogoMIPS (lpj=10000200)
[ 0.584036] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.584036] CPU: L2 cache: 6144K
[ 0.584036] CPU 4/2 -> Node 0
[ 0.584036] CPU: Physical Processor ID: 0
[ 0.584036] CPU: Processor Core ID: 2
[ 0.584036] CPU4: Thermal monitoring enabled (TM2)
[ 0.664716] CPU4: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.674091] checking TSC synchronization [CPU#0 -> CPU#4]: passed.
[ 0.678091] Booting processor 5/6 ip 6000
[ 0.692692] Initializing CPU#5
[ 0.692692] Calibrating delay using timer specific routine.. 5000.11 BogoMIPS (lpj=10000228)
[ 0.692692] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.692692] CPU: L2 cache: 6144K
[ 0.692692] CPU 5/6 -> Node 0
[ 0.692692] CPU: Physical Processor ID: 1
[ 0.692692] CPU: Processor Core ID: 2
[ 0.692692] CPU5: Thermal monitoring enabled (TM2)
[ 0.773393] CPU5: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.782706] checking TSC synchronization [CPU#0 -> CPU#5]: passed.
[ 0.786768] Booting processor 6/3 ip 6000
[ 0.801394] Initializing CPU#6
[ 0.801394] Calibrating delay using timer specific routine.. 5000.07 BogoMIPS (lpj=10000146)
[ 0.801394] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.801394] CPU: L2 cache: 6144K
[ 0.801394] CPU 6/3 -> Node 0
[ 0.801394] CPU: Physical Processor ID: 0
[ 0.801394] CPU: Processor Core ID: 3
[ 0.801394] CPU6: Thermal monitoring enabled (TM2)
[ 0.879553] CPU6: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.890706] checking TSC synchronization [CPU#0 -> CPU#6]: passed.
[ 0.894706] Booting processor 7/7 ip 6000
[ 0.909370] Initializing CPU#7
[ 0.909370] Calibrating delay using timer specific routine.. 5000.11 BogoMIPS (lpj=10000220)
[ 0.909370] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.909370] CPU: L2 cache: 6144K
[ 0.909370] CPU 7/7 -> Node 0
[ 0.909370] CPU: Physical Processor ID: 1
[ 0.909370] CPU: Processor Core ID: 3
[ 0.909370] CPU7: Thermal monitoring enabled (TM2)
[ 0.990078] CPU7: Intel(R) Xeon(R) CPU L5420 @ 2.50GHz stepping 0a
[ 0.999413] checking TSC synchronization [CPU#0 -> CPU#7]: passed.
[ 1.003413] Brought up 8 CPUs
[ 1.006444] Total of 8 processors activated (51504.71 BogoMIPS).
[ 1.011413] CPU0 attaching sched-domain:
[ 1.011413] domain 0: span 0,2
[ 1.011413] groups: 0 2
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 0,2 1,3 4,6 5,7
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU1 attaching sched-domain:
[ 1.011413] domain 0: span 1,3
[ 1.011413] groups: 1 3
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 1,3 4,6 5,7 0,2
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU2 attaching sched-domain:
[ 1.011413] domain 0: span 0,2
[ 1.011413] groups: 2 0
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 0,2 1,3 4,6 5,7
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU3 attaching sched-domain:
[ 1.011413] domain 0: span 1,3
[ 1.011413] groups: 3 1
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 1,3 4,6 5,7 0,2
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU4 attaching sched-domain:
[ 1.011413] domain 0: span 4,6
[ 1.011413] groups: 4 6
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 4,6 5,7 0,2 1,3
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU5 attaching sched-domain:
[ 1.011413] domain 0: span 5,7
[ 1.011413] groups: 5 7
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 5,7 0,2 1,3 4,6
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU6 attaching sched-domain:
[ 1.011413] domain 0: span 4,6
[ 1.011413] groups: 6 4
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 4,6 5,7 0,2 1,3
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] CPU7 attaching sched-domain:
[ 1.011413] domain 0: span 5,7
[ 1.011413] groups: 7 5
[ 1.011413] domain 1: span 0-7
[ 1.011413] groups: 5,7 0,2 1,3 4,6
[ 1.011413] domain 2: span 0-7
[ 1.011413] groups: 0-7
[ 1.011413] net_namespace: 1224 bytes
[ 1.015140] Booting paravirtualized kernel on bare hardware
[ 1.019413] NET: Registered protocol family 16
[ 1.023413] ACPI: bus type pci registered
[ 1.027413] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 5
[ 1.031413] PCI: MCFG area at e0000000 reserved in E820
[ 1.039387] PCI: Using MMCONFIG at e0000000 - e05fffff
[ 1.043387] PCI: Using configuration type 1 for base access
[ 1.047388] ACPI: EC: Look up EC in DSDT
[ 1.054290] ACPI: Interpreter enabled
[ 1.058009] ACPI: (supports S0 S1 S4 S5)
[ 1.062246] ACPI: Using IOAPIC for interrupt routing
[ 1.071602] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 1.075602] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 1.075602] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 1.079602] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 1.083602] PCI: Transparent bridge - 0000:00:1e.0
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP5._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP6._PRT]
[ 1.087602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 1.099569] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 1.103569] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
[ 1.107569] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 1.115562] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
[ 1.124433] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
[ 1.128537] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 *10 11 14 15)
[ 1.132537] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 14 15)
[ 1.142736] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 *7 10 11 14 15)
[ 1.151796] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 1.155797] pnp: PnP ACPI init
[ 1.155797] ACPI: bus type pnp registered
[ 1.159797] pnp 00:00: parse allocated resources
[ 1.163922] pnp 00:00: add io 0xcf8-0xcff flags 0x1
[ 1.167064] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 1.167064] pnp 00:01: parse allocated resources
[ 1.167064] pnp 00:01: add io 0x10-0x1f flags 0x1
[ 1.167064] pnp 00:01: add io 0x24-0x25 flags 0x1
[ 1.167064] pnp 00:01: add io 0x28-0x29 flags 0x1
[ 1.167064] pnp 00:01: add io 0x2c-0x2d flags 0x1
[ 1.167064] pnp 00:01: add io 0x2e-0x2f flags 0x1
[ 1.167064] pnp 00:01: add io 0x30-0x31 flags 0x1
[ 1.167064] pnp 00:01: add io 0x34-0x35 flags 0x1
[ 1.167064] pnp 00:01: add io 0x38-0x39 flags 0x1
[ 1.167064] pnp 00:01: add io 0x3c-0x3d flags 0x1
[ 1.167064] pnp 00:01: add io 0x4e-0x4f flags 0x1
[ 1.167064] pnp 00:01: add io 0x50-0x53 flags 0x1
[ 1.167064] pnp 00:01: add io 0x60-0x60 flags 0x1
[ 1.167064] pnp 00:01: add io 0x64-0x64 flags 0x1
[ 1.167064] pnp 00:01: add io 0x63-0x63 flags 0x1
[ 1.167064] pnp 00:01: add io 0x65-0x65 flags 0x1
[ 1.167064] pnp 00:01: add io 0x67-0x67 flags 0x1
[ 1.167064] pnp 00:01: add io 0x72-0x77 flags 0x1
[ 1.167064] pnp 00:01: add io 0x80-0x80 flags 0x1
[ 1.167064] pnp 00:01: add io 0x90-0x9f flags 0x1
[ 1.167064] pnp 00:01: add io 0xa4-0xa5 flags 0x1
[ 1.167064] pnp 00:01: add io 0xa8-0xa9 flags 0x1
[ 1.167064] pnp 00:01: add io 0xac-0xad flags 0x1
[ 1.167064] pnp 00:01: add io 0xb0-0xb5 flags 0x1
[ 1.167064] pnp 00:01: add io 0xb8-0xb9 flags 0x1
[ 1.167064] pnp 00:01: add io 0xbc-0xbd flags 0x1
[ 1.167064] pnp 00:01: add io 0x4d0-0x4d1 flags 0x1
[ 1.167064] pnp 00:01: add io 0x600-0x63f flags 0x1
[ 1.167064] pnp 00:01: add io 0x800-0x80f flags 0x1
[ 1.167064] pnp 00:01: add io 0xca0-0xcaf flags 0x1
[ 1.167064] pnp 00:01: add io 0x1000-0x107f flags 0x1
[ 1.167064] pnp 00:01: add io 0x1180-0x11bf flags 0x1
[ 1.167064] pnp 00:01: add io 0xfe00-0xfe00 flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfe600000-0xfe6fffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xe0000000-0xefffffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfed20000-0xfed3ffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfee00000-0xfee0ffff flags 0x1
[ 1.167064] pnp 00:01: add mem 0xfef00000-0xfeffffff flags 0x1
[ 1.167064] pnp 00:01: PNP0c02: calling quirk_system_pci_resources+0x0/0x15c
[ 1.167064] pnp 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.167064] pnp 00:02: parse allocated resources
[ 1.167064] pnp 00:02: add io 0x0-0xf flags 0x1
[ 1.167064] pnp 00:02: add io 0x81-0x8f flags 0x1
[ 1.167064] pnp 00:02: add io 0x93-0x9f flags 0x1
[ 1.167064] pnp 00:02: add io 0xc0-0xdf flags 0x1
[ 1.167064] pnp 00:02: add dma 4 flags 0x2
[ 1.167064] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 1.167064] pnp 00:03: parse allocated resources
[ 1.167064] pnp 00:03: add io 0xf0-0xfe flags 0x1
[ 1.167064] pnp 00:03: add irq 13 flags 0x1
[ 1.167064] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 1.167064] pnp 00:04: parse allocated resources
[ 1.167064] pnp 00:04: add io 0x70-0x71 flags 0x1
[ 1.167064] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.167064] pnp 00:05: parse allocated resources
[ 1.167064] pnp 00:05: add io 0x61-0x61 flags 0x1
[ 1.167064] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 1.167064] pnp 00:06: parse allocated resources
[ 1.167064] pnp 00:06: add mem 0xff800000-0xffffffff flags 0x1
[ 1.167064] pnp 00:06: Plug and Play ACPI device, IDs INT0800 (active)
[ 1.167064] pnp 00:07: parse allocated resources
[ 1.167064] pnp 00:07: add io 0x3f8-0x3ff flags 0x1
[ 1.167064] pnp 00:07: add irq 4 flags 0x1
[ 1.167064] pnp 00:07: parse resource options
[ 1.167064] pnp 00:07: new independent option
[ 1.167064] pnp 00:07: new dependent option (priority 0x0)
[ 1.167064] pnp 00:07: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x1)
[ 1.167064] pnp 00:07: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x1)
[ 1.167064] pnp 00:07: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x1)
[ 1.167064] pnp 00:07: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:07: new dependent option (priority 0x2)
[ 1.167064] pnp 00:07: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:07: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:07: end dependent options
[ 1.167064] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.167064] pnp 00:08: parse allocated resources
[ 1.167064] pnp 00:08: add io 0x2f8-0x2ff flags 0x1
[ 1.167064] pnp 00:08: add irq 3 flags 0x1
[ 1.167064] pnp 00:08: parse resource options
[ 1.167064] pnp 00:08: new independent option
[ 1.167064] pnp 00:08: new dependent option (priority 0x1)
[ 1.167064] pnp 00:08: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x0)
[ 1.167064] pnp 00:08: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x1)
[ 1.167064] pnp 00:08: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x1)
[ 1.167064] pnp 00:08: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x3f8 max 0x3f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x2f8 max 0x2f8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x3e8 max 0x3e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000008 flags 0x1
[ 1.167064] pnp 00:08: new dependent option (priority 0x2)
[ 1.167064] pnp 00:08: io min 0x2e8 max 0x2e8 align 1 size 8 flags 0x1
[ 1.167064] pnp 00:08: irq bitmask 00000000,00000000,00000000,00000000,00000000,00000 000,00000000,00000010 flags 0x1
[ 1.167064] pnp 00:08: end dependent options
[ 1.167064] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.167064] pnp: PnP ACPI: found 9 devices
[ 1.171065] ACPI: ACPI bus type pnp unregistered
[ 1.179064] usbcore: registered new interface driver usbfs
[ 1.183065] usbcore: registered new interface driver hub
[ 1.189197] usbcore: registered new device driver usb
[ 1.193197] PCI: Using ACPI for IRQ routing
[ 1.213179] PCI-GART: No AMD northbridge found.
[ 1.217857] hpet clockevent registered
[ 1.217861] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
[ 1.225142] hpet0: 4 64-bit timers, 14318180 Hz
[ 1.229142] ACPI: RTC can wake from S4
[ 1.241272] pnp: the driver 'system' has been registered
[ 1.241280] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[ 1.245479] system 00:01: ioport range 0x600-0x63f has been reserved
[ 1.251883] system 00:01: ioport range 0x800-0x80f has been reserved
[ 1.258295] system 00:01: ioport range 0xca0-0xcaf has been reserved
[ 1.264708] system 00:01: ioport range 0x1000-0x107f has been reserved
[ 1.271167] system 00:01: ioport range 0x1180-0x11bf has been reserved
[ 1.278056] system 00:01: ioport range 0xfe00-0xfe00 has been reserved
[ 1.284642] system 00:01: iomem range 0xfe600000-0xfe6fffff has been reserved
[ 1.291257] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 1.298460] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 1.306056] system 00:01: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 1.314056] system 00:01: iomem range 0xfef00000-0xfeffffff has been reserved
[ 1.321397] system 00:01: driver attached
[ 1.324992] PCI: Bridge: 0000:00:02.0
[ 1.328711] IO window: disabled.
[ 1.332172] MEM window: disabled.
[ 1.335719] PREFETCH window: disabled.
[ 1.339702] PCI: Bridge: 0000:00:04.0
[ 1.343420] IO window: disabled.
[ 1.346882] MEM window: disabled.
[ 1.350429] PREFETCH window: disabled.
[ 1.354412] PCI: Bridge: 0000:00:1c.0
[ 1.357403] IO window: disabled.
[ 1.361399] MEM window: disabled.
[ 1.365405] PREFETCH window: disabled.
[ 1.369407] PCI: Bridge: 0000:00:1c.4
[ 1.373404] IO window: 2000-2fff
[ 1.376972] MEM window: 0xf8000000-0xf80fffff
[ 1.381560] PREFETCH window: disabled.
[ 1.385541] PCI: Bridge: 0000:00:1c.5
[ 1.389406] IO window: 3000-3fff
[ 1.393407] MEM window: 0xf8100000-0xf81fffff
[ 1.397995] PREFETCH window: disabled.
[ 1.401976] PCI: Bridge: 0000:00:1e.0
[ 1.405692] IO window: 4000-4fff
[ 1.409407] MEM window: 0xf8200000-0xf82fffff
[ 1.413995] PREFETCH window: 0x00000000f0000000-0x00000000f7ffffff
[ 1.421410] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 1.421417] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 1.421434] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.429678] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 1.429691] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[ 1.437971] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 1.437988] ACPI: PCI Interrupt 0000:00:1c.5[b] -> GSI 17 (level, low) -> IRQ 17
[ 1.445529] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 1.445537] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 1.445597] NET: Registered protocol family 2
[ 1.489630] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 1.500262] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 1.510827] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 1.518028] TCP: Hash tables configured (established 524288 bind 65536)
[ 1.524711] TCP reno registered
[ 1.540100] NET: Registered protocol family 1
[ 1.544607] checking if image is initramfs...<7>Switched to high resolution mode on CPU 4
[ 1.772839] Switched to high resolution mode on CPU 7
[ 1.772836] Switched to high resolution mode on CPU 6
[ 1.772839] Switched to high resolution mode on CPU 3
[ 1.772836] Switched to high resolution mode on CPU 1
[ 1.772840] Switched to high resolution mode on CPU 2
[ 1.775175] Switched to high resolution mode on CPU 5
[ 1.775723] Switched to high resolution mode on CPU 0
[ 1.827168] it is
[ 2.059381] Freeing initrd memory: 7607k freed
[ 2.066770] Simple Boot Flag at 0x39 set to 0x1
[ 2.075236] audit: initializing netlink socket (disabled)
[ 2.081582] type=2000 audit(1281019578.036:1): initialized
[ 2.088575] Total HugeTLB memory allocated, 0
[ 2.093635] VFS: Disk quotas dquot_6.5.1
[ 2.095229] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.105808] msgmni has been set to 16014
[ 2.112242] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 2.119710] io scheduler noop registered
[ 2.123686] io scheduler anticipatory registered
[ 2.128359] io scheduler deadline registered
[ 2.132710] io scheduler cfq registered (default)
[ 2.137591] pci 0000:06:01.0: Boot video device
[ 2.139167] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 2.139167] assign_interrupt_mode Found MSI capability
[ 2.148703] Allocate Port Service[0000:00:02.0cie00]
[ 2.148759] Allocate Port Service[0000:00:02.0cie01]
[ 2.148841] PCI: Setting latency timer of device 0000:00:04.0 to 64
[ 2.148863] assign_interrupt_mode Found MSI capability
[ 2.155341] Allocate Port Service[0000:00:04.0cie00]
[ 2.156691] Allocate Port Service[0000:00:04.0cie01]
[ 2.156691] Allocate Port Service[0000:00:04.0cie02]
[ 2.156691] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 2.156691] assign_interrupt_mode Found MSI capability
[ 2.162561] Allocate Port Service[0000:00:1c.0cie00]
[ 2.163958] Allocate Port Service[0000:00:1c.0cie02]
[ 2.163958] Allocate Port Service[0000:00:1c.0cie03]
[ 2.163958] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 2.163958] assign_interrupt_mode Found MSI capability
[ 2.169177] Allocate Port Service[0000:00:1c.4cie00]
[ 2.169392] Allocate Port Service[0000:00:1c.4cie02]
[ 2.169392] Allocate Port Service[0000:00:1c.4cie03]
[ 2.169392] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 2.169392] assign_interrupt_mode Found MSI capability
[ 2.174549] Allocate Port Service[0000:00:1c.5cie00]
[ 2.175955] Allocate Port Service[0000:00:1c.5cie02]
[ 2.175955] Allocate Port Service[0000:00:1c.5cie03]
[ 2.175955] AER service couldn't init device 0000:00:02.0cie01 - no _OSC support
[ 2.175955] AER service couldn't init device 0000:00:04.0cie01 - no _OSC support
[ 2.180048] Linux agpgart interface v0.103
[ 2.184435] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 2.194434] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.200630] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.212065] pnp: the driver 'serial' has been registered
[ 2.212065] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.216059] serial 00:07: driver attached
[ 2.216059] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.224865] serial 00:08: driver attached
[ 2.224878] brd: module loaded
[ 2.231977] input: Macintosh mouse button emulation as /class/input/input0
[ 2.239799] pnp: the driver 'i8042 kbd' has been registered
[ 2.239799] pnp: the driver 'i8042 aux' has been registered
[ 2.239799] pnp: the driver 'i8042 kbd' has been unregistered
[ 2.239799] pnp: the driver 'i8042 aux' has been unregistered
[ 2.239799] PNP: No PS/2 controller found. Probing ports directly.
[ 2.246247] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.255905] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.279451] mice: PS/2 mouse device common for all mice
[ 2.284835] pnp: the driver 'rtc_cmos' has been registered
[ 2.284835] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 2.290998] rtc0: alarms up to one month, y3k
[ 2.295121] rtc_cmos 00:04: driver attached
[ 2.295554] cpuidle: using governor ladder
[ 2.299556] cpuidle: using governor menu
[ 2.303558] No iBFT detected.
[ 2.307448] TCP cubic registered
[ 2.309020] NET: Registered protocol family 17
[ 2.316146] registered taskstats version 1
[ 2.320469] rtc_cmos 00:04: setting system clock to 2010-08-05 14:46:20 UTC (1281019580)
[ 2.324785] Freeing unused kernel memory: 392k freed
[ 2.433843] ACPI: ACPI0007:00 is registered as cooling_device0
[ 2.437850] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.449843] ACPI: ACPI0007:01 is registered as cooling_device1
[ 2.456474] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.464133] ACPI: ACPI0007:02 is registered as cooling_device2
[ 2.468137] ACPI: Processor [CPU2] (supports 8 throttling states)
[ 2.480133] ACPI: ACPI0007:03 is registered as cooling_device3
[ 2.488472] ACPI: Processor [CPU3] (supports 8 throttling states)
[ 2.492471] ACPI: ACPI0007:04 is registered as cooling_device4
[ 2.502265] ACPI: Processor [CPU4] (supports 8 throttling states)
[ 2.508787] ACPI: ACPI0007:05 is registered as cooling_device5
[ 2.522254] ACPI: Processor [CPU5] (supports 8 throttling states)
[ 2.529355] ACPI: ACPI0007:06 is registered as cooling_device6
[ 2.540352] ACPI: Processor [CPU6] (supports 8 throttling states)
[ 2.549423] ACPI: ACPI0007:07 is registered as cooling_device7
[ 2.561415] ACPI: Processor [CPU7] (supports 8 throttling states)
[ 2.684347] USB Universal Host Controller Interface driver v3.0
[ 2.690633] ACPI: PCI Interrupt 0000:00:1a.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 2.698498] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 2.698501] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 2.704004] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 2.711697] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820
[ 2.718649] usb usb1: configuration #1 chosen from 1 choice
[ 2.724526] hub 1-0:1.0: USB hub found
[ 2.728489] hub 1-0:1.0: 2 ports detected
[ 2.742353] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
[ 2.748726] e1000e: Copyright (c) 1999-2008 Intel Corporation.
[ 2.755095] No dock devices found.
[ 2.765457] SCSI subsystem initialized
[ 2.781067] libata version 3.00 loaded.
[ 2.845936] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.853930] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.861929] usb usb1: Product: UHCI Host Controller
[ 2.869935] usb usb1: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 2.877158] usb usb1: SerialNumber: 0000:00:1a.0
[ 2.882773] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 2.902932] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 2.902935] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.910808] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 2.922588] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001840
[ 2.974950] usb usb2: configuration #1 chosen from 1 choice
[ 2.980785] hub 2-0:1.0: USB hub found
[ 2.984770] hub 2-0:1.0: 2 ports detected
[ 3.105021] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.115618] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.172971] usb usb2: Product: UHCI Host Controller
[ 3.179398] usb usb2: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 3.185884] usb usb2: SerialNumber: 0000:00:1d.0
[ 3.255127] ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 22 (level, low) -> IRQ 22
[ 3.260103] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 3.260106] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 3.335151] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 3.344610] uhci_hcd 0000:00:1d.1: irq 22, io base 0x00001860
[ 3.351170] usb usb3: configuration #1 chosen from 1 choice
[ 3.355117] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 3.365181] hub 3-0:1.0: USB hub found
[ 3.531142] hub 3-0:1.0: 2 ports detected
[ 3.661956] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 3.670347] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.678341] usb usb3: Product: UHCI Host Controller
[ 3.687123] usb usb3: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 3.721376] usb usb3: SerialNumber: 0000:00:1d.1
[ 3.763772] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 21
[ 3.770714] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 3.770717] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.775736] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 3.781373] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001880
[ 3.789387] usb usb4: configuration #1 chosen from 1 choice
[ 3.795893] usb 1-1: configuration #1 chosen from 1 choice
[ 3.835846] hub 4-0:1.0: USB hub found
[ 3.835846] usb 1-1: New USB device found, idVendor=14dd, idProduct=0002
[ 3.835846] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.835846] usb 1-1: Product: Multidevice
[ 3.835846] usb 1-1: Manufacturer: Peppercon AG
[ 3.835846] usb 1-1: SerialNumber: 0483ce0108495ed97CE4F555C62C01B7
[ 3.913577] hub 4-0:1.0: 2 ports detected
[ 4.022113] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.030101] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.040200] usb usb4: Product: UHCI Host Controller
[ 4.046106] usb usb4: Manufacturer: Linux 2.6.26-2-amd64 uhci_hcd
[ 4.054421] usb usb4: SerialNumber: 0000:00:1d.2
[ 4.070092] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 22 (level, low) -> IRQ 22
[ 4.130906] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 4.130910] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 4.139616] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 5
[ 4.154409] ehci_hcd 0000:00:1a.7: debug port 1
[ 4.158414] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 4.158420] ehci_hcd 0000:00:1a.7: irq 22, io mem 0xf8500800
[ 4.171071] usbcore: registered new interface driver hiddev
[ 4.186166] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.198229] usb usb5: configuration #1 chosen from 1 choice
[ 4.198160] usbcore: registered new interface driver usbhid
[ 4.198160] usbhid: v2.6:USB HID core driver
[ 4.214501] hub 5-0:1.0: USB hub found
[ 4.214522] usb 1-1: USB disconnect, address 2
[ 4.227315] hub 5-0:1.0: 2 ports detected
[ 4.336648] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.340398] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.364411] usb usb5: Product: EHCI Host Controller
[ 4.372412] usb usb5: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd
[ 4.377832] usb usb5: SerialNumber: 0000:00:1a.7
[ 4.385832] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 4.392881] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 4.392884] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 4.398382] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 6
[ 4.409831] ehci_hcd 0000:00:1d.7: debug port 1
[ 4.414872] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 4.414877] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8500c00
[ 4.434826] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.443162] usb usb6: configuration #1 chosen from 1 choice
[ 4.449838] hub 6-0:1.0: USB hub found
[ 4.456241] hub 6-0:1.0: 6 ports detected
[ 4.698671] usb usb6: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.706191] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.882605] usb usb6: Product: EHCI Host Controller
[ 4.890605] usb usb6: Manufacturer: Linux 2.6.26-2-amd64 ehci_hcd
[ 4.896029] usb usb6: SerialNumber: 0000:00:1d.7
[ 4.906590] ahci 0000:00:1f.2: version 3.0
[ 4.906590] ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 17 (level, low) -> IRQ 17
[ 5.022584] usb 5-1: new high speed USB device using ehci_hcd and address 2
[ 5.299422] usb 5-1: configuration #1 chosen from 1 choice
[ 5.311412] input: Peppercon AG Multidevice as /class/input/input1
[ 5.408436] input,hidraw0: USB HID v1.01 Mouse [Peppercon AG Multidevice] on usb-0000:00:1a.7-1
[ 5.421713] input: Peppercon AG Multidevice as /class/input/input2
[ 5.452938] input,hidraw1: USB HID v1.01 Keyboard [Peppercon AG Multidevice] on usb-0000:00:1a.7-1
[ 5.462526] usb 5-1: New USB device found, idVendor=14dd, idProduct=0002
[ 5.475770] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.483770] usb 5-1: Product: Multidevice
[ 5.490770] usb 5-1: Manufacturer: Peppercon AG
[ 5.495532] usb 5-1: SerialNumber: 0483ce0108495ed97CE4F555C62C01B7
[ 6.231839] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x2f impl SATA mode
[ 6.240380] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part
[ 6.295405] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 6.303409] scsi0 : ahci
[ 6.303409] scsi1 : ahci
[ 6.309134] scsi2 : ahci
[ 6.311879] scsi3 : ahci
[ 6.311880] scsi4 : ahci
[ 6.321088] scsi5 : ahci
[ 6.321176] ata1: SATA max UDMA/133 irq_stat 0x00400040, irq 1274
[ 6.334133] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
[ 6.342027] ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
[ 6.350029] ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed
[ 6.357948] ata5: DUMMY
[ 6.401923] ata6: SATA max UDMA/133 abar m2048@0xf8500000 port 0xf8500380 irq 1274
[ 7.768943] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7.828133] ata1.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 7.828306] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 7.853663] ata1.00: configured for UDMA/133
[ 8.762544] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8.810392] ata2.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 8.811202] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 8.835374] ata2.00: configured for UDMA/133
[ 10.142643] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 10.791190] ata3.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 10.797247] ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 10.808351] ata3.00: configured for UDMA/133
[ 11.719811] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 11.986318] ata4.00: ATA-8: ST9500420AS, 0002SDM1, max UDMA/133
[ 11.992473] ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 12.007553] ata4.00: configured for UDMA/133
[ 12.343300] ata6: SATA link down (SStatus 0 SControl 300)
[ 12.362120] scsi 0:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.827239] scsi 1:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.839447] scsi 2:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.848398] scsi 3:0:0:0: Direct-Access ATA ST9500420AS 0002 PQ: 0 ANSI: 5
[ 12.870240] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 12.892234] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 13.013765] eth0: (PCI Express:2.5GB/s:Width x1) 00:30:48:67:31:d6
[ 13.033485] eth0: Intel(R) PRO/1000 Network Connection
[ 13.041931] eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
[ 13.049756] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 13.054716] PCI: Setting latency timer of device 0000:05:00.0 to 64
[ 13.167083] eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:67:31:d7
[ 13.175228] eth1: Intel(R) PRO/1000 Network Connection
[ 13.181719] eth1: MAC: 2, PHY: 2, PBA No: ffffff-0ff
[ 13.256962] Driver 'sd' needs updating - please use bus_type methods
[ 13.264577] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 13.272490] sd 0:0:0:0: [sda] Write Protect is off
[ 13.277516] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.277547] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.289992] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
[ 13.297934] sd 0:0:0:0: [sda] Write Protect is off
[ 13.305498] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 13.305519] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.317149] sda: sda1 sda2 sda3 sda4
[ 13.369515] sd 0:0:0:0: [sda] Attached SCSI disk
[ 13.401510] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 13.413077] sd 1:0:0:0: [sdb] Write Protect is off
[ 13.418545] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 13.418568] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.431417] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
[ 13.439214] sd 1:0:0:0: [sdb] Write Protect is off
[ 13.444235] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 13.444253] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.454511] sdb: sdb1 sdb2 sdb3 sdb4
[ 13.520029] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 13.524904] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 13.611048] sd 2:0:0:0: [sdc] Write Protect is off
[ 13.616078] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 13.616096] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.628138] sd 2:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
[ 13.636083] sd 2:0:0:0: [sdc] Write Protect is off
[ 13.643586] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 13.643798] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.652740] sdc: sdc1
[ 13.701174] sd 2:0:0:0: [sdc] Attached SCSI disk
[ 13.707722] sd 3:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[ 13.768291] sd 3:0:0:0: [sdd] Write Protect is off
[ 13.773340] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 13.773359] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.785372] sd 3:0:0:0: [sdd] 976773168 512-byte hardware sectors (500108 MB)
[ 13.790825] sd 3:0:0:0: [sdd] Write Protect is off
[ 13.798279] sd 3:0:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 13.798296] sd 3:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 13.807300] sdd: sdd1
[ 13.842634] sd 3:0:0:0: [sdd] Attached SCSI disk
[ 14.115107] md: raid1 personality registered for level 1
[ 14.131761] md: md0 stopped.
[ 14.214641] md: bind<sdb1>
[ 14.218650] md: bind<sda1>
[ 14.228571] raid1: raid set md0 active with 2 out of 2 mirrors
[ 14.236408] md: md1 stopped.
[ 14.334170] md: bind<sdb2>
[ 14.337088] md: bind<sda2>
[ 14.347529] raid1: raid set md1 active with 2 out of 2 mirrors
[ 14.355727] md: md2 stopped.
[ 14.505367] md: bind<sda3>
[ 14.508638] md: bind<sdb3>
[ 14.511706] md: kicking non-fresh sda3 from array!
[ 14.517039] md: unbind<sda3>
[ 14.521039] md: export_rdev(sda3)
[ 14.531597] raid1: raid set md2 active with 1 out of 2 mirrors
[ 14.551393] md: md3 stopped.
[ 14.605925] md: bind<sdb4>
[ 14.609925] md: bind<sda4>
[ 14.624698] raid1: raid set md3 active with 2 out of 2 mirrors
[ 14.631521] md: md4 stopped.
[ 14.669304] md: bind<sdc1>
[ 14.673275] md: bind<sdd1>
[ 14.683366] raid1: raid set md4 active with 2 out of 2 mirrors
[ 14.760828] device-mapper: uevent: version 1.0.3
[ 14.768951] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 14.847613] PM: Starting manual resume from disk
[ 14.885328] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 14.908660] SGI XFS Quota Management subsystem
[ 14.912661] Filesystem "md1": Disabling barriers, not supported by the underlying device
[ 14.920661] XFS mounting filesystem md1
[ 15.110893] Ending clean XFS mount for filesystem: md1
[ 17.438589] udevd version 125 started
[ 17.815323] input: Power Button (FF) as /class/input/input3
[ 17.842475] ACPI: Power Button (FF) [PWRF]
[ 17.852263] input: Power Button (CM) as /class/input/input4
[ 17.889629] ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 17 (level, low) -> IRQ 17
[ 17.901344] input: PC Speaker as /class/input/input5
[ 18.082676] ACPI: Power Button (CM) [PWRB]
[ 18.262564] Error: Driver 'pcspkr' is already registered, aborting...
[ 19.970509] Filesystem "md1": Disabling barriers, not supported by the underlying device
[ 21.025244] loop: module loaded
[ 21.054985] ipmi message handler version 39.2
[ 21.067961] IPMI System Interface driver.
[ 21.072957] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca2, slave address 0x20, irq 0
[ 21.191106] ipmi: Found new BMC (man_id: 0x0028c5, prod_id: 0x0004, dev_id: 0x22)
[ 21.199105] IPMI kcs interface initialized
[ 21.296027] w83627hf: Found W83627HF chip at 0x290
[ 21.300353] w83627hf w83627hf.656: Enabling temp2, readings might not make sense
[ 21.308677] w83627hf w83627hf.656: Enabling temp3, readings might not make sense
[ 21.327912] coretemp coretemp.0: Using relative temperature scale!
[ 21.337977] coretemp coretemp.1: Using relative temperature scale!
[ 21.344852] coretemp coretemp.2: Using relative temperature scale!
[ 21.352840] coretemp coretemp.3: Using relative temperature scale!
[ 21.361047] coretemp coretemp.4: Using relative temperature scale!
[ 21.367940] coretemp coretemp.5: Using relative temperature scale!
[ 21.375939] coretemp coretemp.6: Using relative temperature scale!
[ 21.383942] coretemp coretemp.7: Using relative temperature scale!
[ 22.638207] kjournald starting. Commit interval 5 seconds
[ 22.647304] EXT3 FS on md0, internal journal
[ 22.651818] EXT3-fs: mounted filesystem with ordered data mode.
[ 22.661520] Filesystem "dm-0": Disabling barriers, not supported by the underlying device
[ 22.673519] XFS mounting filesystem dm-0
[ 23.090546] Ending clean XFS mount for filesystem: dm-0
[ 23.098551] Filesystem "md2": Disabling barriers, not supported by the underlying device
[ 23.169293] XFS mounting filesystem md2
[ 23.444104] Ending clean XFS mount for filesystem: md2
[ 23.869974] Adding 87109624k swap on /dev/mapper/vg0-swapspare. Priority:-1 extents:1 across:87109624k






--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 4C5BB064.1040907@webdevworld.com">http://lists.debian.org/4C5BB064.1040907@webdevworld.com
 
Old 08-06-2010, 10:25 AM
mimo
 
Default veryPC, Seagate, raid - caught in the middle

Hi Kalpesh

thanks for your suggestions. I guess I was wondering how it's possible - among - other things - for one partition on a disk to fail and the others to remain intact and whether anyone else had seen that before or whether that was my fault setting it up like that.
Also, I'm wondering what sort of experience others have with using laptop 2.5" drives rather than server class ones. Maybe that's where I went wrong.
You mention the SATA backplane - what is that? Also, I think it's strange that different drives show problems..

Anyway thanks a lot

mimo

On Friday 06 August 2010 07:49:08 kalpesh thaker wrote:
> Hi Mimo,
>
> I have had similar issues to this. it happened some time back, however,
> i had a raid 0 setup, of which data became
> inconsistent very often...and i got endless array failures.
>
> Naturally, i replaced the drives, after which the same issue happened
> some weeks later. it took me a while to figure out
> my problem, which in the end was a faulty SATA Raid backplane. Once i
> had changed that, everything ran fine.
>
> Depending on what type of machine you are using, id recommend trying
> another backplane, or replacing the
> SATA cables. If this machine is fairly old, i'd also recommend removing
> the backplane and spraying the internal
> and external connectors with compressed air to remove any dust that
> sometimes settles there. Also, make sure that
> your servers are well ventilated, and that the drives are not
> overheating. If all else if fine, then i'd agree that
> your motherboard might be faulty.
>
> In my case of the 'faulty' drives, i was advised by our hardware
> supplier to run a diagnostic on the drives,
> using Seagate Seatools before sending them back for warranty
> replacement. Ironically, Seatools had passed all
> the drives on the extended tests, and to verify, the drives did actually
> run fine in another machine.
>


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 201008061125.46408.mimo@restoel.net">http://lists.debian.org/201008061125.46408.mimo@restoel.net
 
Old 08-06-2010, 11:11 AM
Christian Svensson
 
Default veryPC, Seagate, raid - caught in the middle

I've seen this before when one drive was about to crash.
One array of my three software RAID-5 arrays would randomly fail - same member drive though.
dmesg would log a failed write and that particular partition would be kicked out of the array.



Replacing the drive solved the problem for me.
Greetings,

Christian Svensson
System administrator - Kalmar NDC

On Fri, Aug 6, 2010 at 12:25, mimo <mimo@restoel.net> wrote:


Hi Kalpesh



thanks for your suggestions. I guess I was wondering how it's possible - among - other things - for one partition on a disk to fail and the others to remain intact and whether anyone else had seen that before or whether that was my fault setting it up like that.



Also, I'm wondering what sort of experience others have with using laptop 2.5" drives rather than server class ones. Maybe that's where I went wrong.

You mention the SATA backplane - what is that? Also, I think it's strange that different drives show problems..



Anyway thanks a lot



mimo



On Friday 06 August 2010 07:49:08 kalpesh thaker wrote:

> Hi Mimo,

>

> I have had similar issues to this. it happened some time back, however,

> i had a raid 0 setup, of which data became

> inconsistent very often...and i got endless array failures.

>

> Naturally, i replaced the drives, after which the same issue happened

> some weeks later. it took me a while to figure out

> my problem, which in the end was a faulty SATA Raid backplane. Once i

> had changed that, everything ran fine.

>

> Depending on what type of machine you are using, id recommend trying

> another backplane, or replacing the

> SATA cables. If this machine is fairly old, i'd also recommend removing

> the backplane and spraying the internal

> and external connectors with compressed air to remove any dust that

> sometimes settles there. Also, make sure that

> your servers are well ventilated, and that the drives are not

> overheating. If all else if fine, then i'd agree that

> your motherboard might be faulty.

>

> In my case of the 'faulty' drives, i was advised by our hardware

> supplier to run a diagnostic on the drives,

> using Seagate Seatools before sending them back for warranty

> replacement. Ironically, Seatools had passed all

> the drives on the extended tests, and to verify, the drives did actually

> run fine in another machine.

>





--

To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org

with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org

Archive: http://lists.debian.org/201008061125.46408.mimo@restoel.net





--

Meddelandet har kontrollerats mot virus samt skadligt

innehåll av MailScanner och förmodas vara säkert.
 
Old 08-06-2010, 12:29 PM
Thomas Goirand
 
Default veryPC, Seagate, raid - caught in the middle

----- Original message -----
> On Friday 06 August 2010 07:49:08 kalpesh thaker wrote:
> > Hi Mimo,
> >
> > I have had similar issues to this. it happened some time back,
> > however,* i had a raid 0 setup, of which data became
> > inconsistent very often...and i got endless array failures.

You may also want to check for the power of you
HDD. If it is underpowered, the what you describe
can happen. The way to check is to see if there is
some variation in the 12 V, so you would put a tiny
cheap voltmetre in the alternative mode (sorry, not
100 percent sure of how to write this in en). Then
it should display zero if there's no issue. When
you do the test, make sure you load the server (both
cpu, ram an hdd activity: "apt-get install stress"
to do this). As you are running a twin server, you
will have to put both under load.

This isn't rocket science, but it saved me once at
least, and with the above, you'll make sure it's not
a power issue, and you'll go for further
investigation keeping in mind it wasn't a power
issue.

I hope this helps,

Thomas


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 1281097786.7948.2.camel@Nokia-N900-42-11">http://lists.debian.org/1281097786.7948.2.camel@Nokia-N900-42-11
 
Old 08-06-2010, 12:53 PM
mimo
 
Default veryPC, Seagate, raid - caught in the middle

Thanks Christian. It's really bugging me as I can't understand why 2 months ago one drive had problems and replacing it fixed those apparently. But then two weeks ago a different drive suddenly goes down. Maybe that series of Seagate drives are "evil "? But then.. I did stress test the broken drive (the one from 2 months ago) heavily using a USB controller and it hasn't shown any problems so far (using badblocks and Seatools).
Maybe it's a strange combination of factors as an i2c module I inserted after running sensors-detect was spamming my syslog with this message:

i801_smbus 0000:00:1f.3: Bus collision! SMBus may be locked until next hard reset. (sorry!)

Yesterday I took out what I believe to be the culprit module from /etc/modules, rebooted, rebuilt the md2, started stressing the drives and so far so good. But then the problems seem to only show after a week or two...

I don't know enough about i2c or any of this but could their be a connection between the i2c part of the machine and the SATA controller?!

mimo

On Friday 06 August 2010 12:11:03 Christian Svensson wrote:
> I've seen this before when one drive was about to crash.
> One array of my three software RAID-5 arrays would randomly fail - same
> member drive though.
> dmesg would log a failed write and that particular partition would be kicked
> out of the array.
>
> Replacing the drive solved the problem for me.
>
> Greetings,
>
> Christian Svensson
> System administrator - Kalmar NDC
>


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 201008061353.15452.mimo@restoel.net">http://lists.debian.org/201008061353.15452.mimo@restoel.net
 
Old 08-06-2010, 01:02 PM
mimo
 
Default veryPC, Seagate, raid - caught in the middle

On Friday 06 August 2010 13:29:46 Thomas Goirand wrote:
> You may also want to check for the power of you
> HDD. If it is underpowered, the what you describe
> can happen. The way to check is to see if there is
> some variation in the 12 V, so you would put a tiny
> cheap voltmetre in the alternative mode (sorry, not
> 100 percent sure of how to write this in en). Then
> it should display zero if there's no issue. When
> you do the test, make sure you load the server (both
> cpu, ram an hdd activity: "apt-get install stress"
> to do this). As you are running a twin server, you
> will have to put both under load.

When I googled it first I somewhere found a bout power problems causing sporadic failures like these but then I spoke to the manufacturers and they said the power supply on the machines was pretty much oversized (I don't remember the exact numbers - maybe 750 and each machine would need a max of 300).

I have a munin graph of voltages from sensors and that looks fine - the 12V and all the others look totally stable. Would you trust this?

mimo


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 201008061402.38442.mimo@restoel.net">http://lists.debian.org/201008061402.38442.mimo@restoel.net
 
Old 08-06-2010, 01:09 PM
Michael Moritz
 
Default veryPC, Seagate, raid - caught in the middle

On Friday 06 August 2010 14:02:37 mimo wrote:
> I have a munin graph of voltages from sensors and that looks fine - the 12V and all the others look totally stable. Would you trust this?

Hmmm... now just looked at these and realise the -12V is -6.06 and the +12V is 15.50. But the that may just be a sensors weirdness as it's the same on the other node (which has never failed but uses 2 WD drives).

Sorry I hope I don't annoy too many people by posting so much to the list...

mimo


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 201008061409.21425.mimo@gn.apc.org">http://lists.debian.org/201008061409.21425.mimo@gn.apc.org
 
Old 08-07-2010, 03:52 AM
Henrique de Moraes Holschuh
 
Default veryPC, Seagate, raid - caught in the middle

On Fri, 06 Aug 2010, mimo wrote:
> But then two weeks ago a different drive suddenly goes down. Maybe that
> series of Seagate drives are "evil "? But then.. I did stress test the

You're using *laptop* HDs for server workloads. What did you expect? Do
you honestly believe laptop HDs are built with the same design goals as
server HDs?

If you want cheap storage that will handle server workloads, stay away from
SFF bays, which only give you two choices for spinning media: laptop HDs or
enterprise HDs.

LFF bays at least let you use desktop RAID-compatible HDs such as most
Seagate desktop models (just don't go around thinking that all LFF HDs are
RAID-compatible. A lot of recent models from Western Digital aren't, for
example).

--
"One disk to rule them all, One disk to find them. One disk to bring
them all and in the darkness grind them. In the Land of Redmond
where the shadows lie." -- The Silicon Valley Tarot
Henrique Holschuh


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 20100807035255.GA16342@khazad-dum.debian.net">http://lists.debian.org/20100807035255.GA16342@khazad-dum.debian.net
 
Old 08-07-2010, 05:24 AM
Seth Mattinen
 
Default veryPC, Seagate, raid - caught in the middle

On 8/6/10 8:52 PM, Henrique de Moraes Holschuh wrote:
>
> LFF bays at least let you use desktop RAID-compatible HDs such as most
> Seagate desktop models (just don't go around thinking that all LFF HDs are
> RAID-compatible. A lot of recent models from Western Digital aren't, for
> example).
>


Don't ever use the WD green drives for servers.

~Seth


--
To UNSUBSCRIBE, email to debian-isp-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Archive: 4C5CEDFC.3010809@rollernet.us">http://lists.debian.org/4C5CEDFC.3010809@rollernet.us
 

Thread Tools




All times are GMT. The time now is 03:09 PM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright ©2007 - 2008, www.linux-archive.org