boot problem after disk change on raid1
Hello,
I have two disks sda and sdb. One of the was broken so I have changed the broken disk with a working one. I started the server in rescue mode, and created the partional table, and added all the partitions to the software raid. I have added the partitions to the RAID, and reboot. # mdadm /dev/md0 --add /dev/sdb1 # mdadm /dev/md1 --add /dev/sdb2 # mdadm /dev/md2 --add /dev/sdb3 # mdadm /dev/md3 --add /dev/sdb4 After reboot, server did not boot. So I do the followings: # mount /dev/md1 /mnt/rescue # mount /dev/md0 /mnt/rescue/boot # mount -o bind /dev /mnt/rescue/dev# mount -o bind /proc /mnt/rescue/proc # mount -o bind /dev/shm /mnt/rescue/dev/shm # mount -o bind /sys /mnt/rescue/sys # chroot /mnt/rescue I checked the device.map # cat /boot/grub/device.map(hd0)** /dev/sda (hd1)** /dev/sdb And, install the grub. # grub Probing devices to guess BIOS drives. This may take a long time. *** GNU GRUB* version 0.97* (640K lower / 3072K upper memory)*[ Minimal BASH-like line editing is supported.* For the first word, TAB ** lists possible command completions.* Anywhere else TAB lists the possible** completions of a device/filename.] grub> root (hd0,0)root (hd0,0) *Filesystem type is ext2fs, partition type 0xfdgrub> setup (hd0) setup (hd0)*Checking if "/boot/grub/stage1" exists... yes *Checking if "/boot/grub/stage2" exists... yes*Checking if "/boot/grub/e2fs_stage1_5" exists... yes *Running "embed /boot/grub/e2fs_stage1_5 (hd0)"...* 15 sectors are embedded.succeeded *Running "install /boot/grub/stage1 (hd0) (hd0)1+15 p (hd0,0)/boot/grub/stage2 /boot/grub/grub.conf"... succeeded Done.grub> root (hd1,0) root (hd1,0)*Filesystem type is ext2fs, partition type 0xfd grub> setup (hd1)setup (hd1) *Checking if "/boot/grub/stage1" exists... yes*Checking if "/boot/grub/stage2" exists... yes *Checking if "/boot/grub/e2fs_stage1_5" exists... yes*Running "embed /boot/grub/e2fs_stage1_5 (hd1)"...* 15 sectors are embedded. succeeded*Running "install /boot/grub/stage1 (hd1) (hd1)1+15 p (hd1,0)/boot/grub/stage2 /boot/grub/grub.conf"... succeeded Done.grub> quit quit But it still does not boot. What should I do at this point? What do you suggest? Disk informations # fdisk -l /dev/sd[ab] Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00090dd1 ** Device Boot***** Start******** End***** Blocks** Id* System /dev/sda1** *********** 1******** 131**** 1052226** fd* Linux raid autodetect /dev/sda2************ 132******* 5353*** 41945715** fd* Linux raid autodetect /dev/sda3*********** 5354****** 96733** 734009850** fd* Linux raid autodetect /dev/sda4********** 96734***** 182401** 688128210** fd* Linux raid autodetect Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf5c3aa6a ** Device Boot***** Start******** End***** Blocks** Id* System /dev/sdb1** *********** 1******** 131**** 1052226** fd* Linux raid autodetect /dev/sdb2************ 132******* 5353*** 41945715** fd* Linux raid autodetect /dev/sdb3*********** 5354****** 96733** 734009850** fd* Linux raid autodetect /dev/sdb4********** 96734***** 182401** 688128210** fd* Linux raid autodetect Raid info # cat /proc/mdstat Personalities : [raid1] md3 : active raid1 sda4[0] sdb4[2] ***** 688128128 blocks [2/1] [U_] ******* resync=DELAYED md2 : active raid1 sda3[0] sdb3[2] ***** 734009728 blocks [2/1] [U_] ***** [>....................]* recovery =* 1.8% (13651648/734009728) finish=133.5min speed=89915K/sec md1 : active raid1 sdb2[2] sda2[0] ***** 41945600 blocks [2/1] [U_] ******* resync=DELAYED md0 : active raid1 sda1[0] sdb1[1] ***** 1052160 blocks [2/2] [UU] unused devices: <none> Mount informations /dev/md0 is mounted /boot /dev/md1 is mounted / /dev/md2 and /dev/md3 is for backup and some personal data Here is the grub.conf # cat /mnt/rescue/boot/grub/grub.conf timeout 5default 0 fallback 1title CentOS (2.6.18-238.19.1.el5) root (hd1,0)kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 initrd /initrd-2.6.18-238.19.1.el5.imgtitle CentOS (2.6.18-238.9.1.el5) root (hd0,0)kernel /vmlinuz-2.6.18-238.9.1.el5 ro root=/dev/md1 vga=0x317 initrd /initrd-2.6.18-238.9.1.el5.imgtitle CentOS (2.6.18-194.26.1.el5) root (hd0,0)kernel /vmlinuz-2.6.18-194.26.1.el5 ro root=/dev/md1 vga=0x317 initrd /initrd-2.6.18-194.26.1.el5.imgtitle CentOS (2.6.18-194.3.1.el5) root (hd0,0)kernel /vmlinuz-2.6.18-194.3.1.el5 ro root=/dev/md1 vga=0x317 initrd /initrd-2.6.18-194.3.1.el5.imgtitle CentOS (2.6.18-164.15.1.el5) root (hd0,0)kernel /vmlinuz-2.6.18-164.15.1.el5 ro root=/dev/md1 vga=0x317 initrd /initrd-2.6.18-164.15.1.el5.imgtitle CentOS Linux (2.6.18-164.11.1.el5) root (hd0,0)kernel /boot/vmlinuz-2.6.18-164.11.1.el5 ro root=/dev/md1 vga=0x317 initrd /boot/initrd-2.6.18-164.11.1.el5.img _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
boot problem after disk change on raid1
--On Wednesday, September 07, 2011 08:22:47 PM +0300 Bünyamin İzzet
<bunyamin.izzet@gmail.com> wrote: > Hello, > > I have two disks sda and sdb. One of the was broken so I have changed the > broken disk with a working one. I started the server in rescue mode, and > created the partional table, and added all the partitions to the software > raid. Sounds like the 'no boot record' issue. Here's an extract from one of my server change logs, for setting things up *before* they go bad: - made sure we have boot blocks on both disks, based on information at http://grub.enbug.org/MirroringRAID modified /boot/grub/device.map from: (hd0) /dev/sda (hd1) /dev/sdb to: (hd0) /dev/sda (hd0) /dev/sdb and then: # grub grub> device (hd0) /dev/sdb grub> root (hd0,0) grub> setup (hd0) grub> quit With the above in place you can boot from either disk as long as your BIOS will let you select the boot device. I've had older systems where the BIOS didn't have that option, in which case the 'in event of breakage' procedure would be to take the working slave disk and put it on the controller cable that originally had the flawed master disk. ># cat /boot/grub/device.map > (hd0) /dev/sda > (hd1) /dev/sdb Not quite right (need hd0 on both) Devin _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
boot problem after disk change on raid1
--On Wednesday, September 07, 2011 02:38:14 PM -0600 Devin Reade
<gdr@gno.org> wrote: > Sounds like the 'no boot record' issue. Here's an extract from one > of my server change logs, for setting things up *before* they go bad: I should add that, with a tested boot-from-alternate disk in place I've been able to avoid the boot into rescue mode procedure, thus minimizing down time. Ignoring the case of hot-swap devices and hot spares: - shut down system - remove faulty disk - add in replacement disk - reboot to normal run level (3 or 5). RAID is now running in degraded mode, but you're back in operation - do disk paritioning, MBR init, and reconstruction while in service Devin _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
boot problem after disk change on raid1
On Wed, Sep 7, 2011 at 11:38 PM, Devin Reade <gdr@gno.org> wrote:
--On Wednesday, September 07, 2011 08:22:47 PM +0300 Bünyamin İzzet <bunyamin.izzet@gmail.com> wrote: * * * *- made sure we have boot blocks on both disks, based on information * * * * *at http://grub.enbug.org/MirroringRAID * * * * * * * *modified /boot/grub/device.map from: * * * * * * * * * * * *(hd0) * * /dev/sda * * * * * * * * * * * *(hd1) * * /dev/sdb * * * * * * * *to: * * * * * * * * * * * *(hd0) * * /dev/sda * * * * * * * * * * * *(hd0) * * /dev/sdb I have changed the device.map as you said * * * * * * * * *and then: * * * * * * * * * * * *# grub * * * * * * * * * * * *grub> device (hd0) /dev/sdb * * * * * * * * * * * *grub> root (hd0,0) * * * * * * * * * * * *grub> setup (hd0) * * * * * * * * * * * *grub> quit And, it is done too. It still does not boot. I could not see the error message, because it is a dedicated server and I am not sitting at the monitor of the server. So I type the lines in grub.conf manually to see the error (I'm not sure if it is the right thing to see the error). # grub Probing devices to guess BIOS drives. This may take a long time. *** GNU GRUB* version 0.97* (640K lower / 3072K upper memory) *[ Minimal BASH-like line editing is supported.* For the first word, TAB ** lists possible command completions.* Anywhere else TAB lists the possible ** completions of a device/filename.] grub> root (hd1,0) root (hd1,0) *Filesystem type is ext2fs, partition type 0xfd grub> kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 ** [Linux-bzImage, setup=0x1e00, size=0x1fe01c] grub> initrd /initrd-2.6.18-238.19.1.el5.img initrd /initrd-2.6.18-238.19.1.el5.img Error 28: Selected item cannot fit into memory grub> quit quit If it is not the right thing to see the error message at boot time, is there any chance to log grub errors, boot errors? Thanks, Bunyamin. _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
boot problem after disk change on raid1
Bnyamin zzet <bunyamin.izzet@gmail.com> wrote:
> On Wed, Sep 7, 2011 at 11:38 PM, Devin Reade <gdr@gno.org> wrote: > [snip] >> # grub >> grub> device (hd0) /dev/sdb >> grub> root (hd0,0) >> grub> setup (hd0) >> grub> quit > > It still does not boot. I could not see the error message, because it is a > dedicated server and I am not sitting at the monitor of the server. So I > type the lines in grub.conf manually to see the error (I'm not sure if it is > the right thing to see the error). If you mean that you typed the lines I gave above into grub.conf, then that was not what was intended (and I doubt that it would work). My intent was that you get the system booted and running normally (perhaps via the rescue disk), and after that execute 'grub' interactively and issue those commands. Devin _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
boot problem after disk change on raid1
On Thu, Sep 8, 2011 at 8:11 AM, Devin Reade <gdr@gno.org> wrote:
Bünyamin Ýzzet <bunyamin.izzet@gmail.com> wrote: > On Wed, Sep 7, 2011 at 11:38 PM, Devin Reade <gdr@gno.org> wrote: > [snip] >> * * * * * * * * * * * *# grub >> * * * * * * * * * * * *grub> device (hd0) /dev/sdb >> * * * * * * * * * * * *grub> root (hd0,0) >> * * * * * * * * * * * *grub> setup (hd0) >> * * * * * * * * * * * *grub> quit > > It still does not boot. I could not see the error message, because it is a > dedicated server and I am not sitting at the monitor of the server. So I > type the lines in grub.conf manually to see the error (I'm not sure if it is > the right thing to see the error). If you mean that you typed the lines I gave above into grub.conf, then that was not what was intended (and I doubt that it would work). *My intent was that you get the system booted and running normally (perhaps via the rescue disk), and after that execute 'grub' interactively and issue those commands. *Devin As you said, I booted the system via rescue disk, and execute grub and issue those commands. Then, I reboot the system, but it does not boot. Then I searched on google about logging grub errors, which I could not find anything useful (meybe I did not look enough). So that, in rescue system, I execute grub and type commands in grub.conf (results are below) to see which error occurs. # grub Probing devices to guess BIOS drives. This may take a long time. GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename.] grub> root (hd1,0) root (hd1,0) Filesystem type is ext2fs, partition type 0xfd grub> kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 [Linux-bzImage, setup=0x1e00, size=0x1fe01c] grub> initrd /initrd-2.6.18-238.19.1.el5.img initrd /initrd-2.6.18-238.19.1.el5.img Error 28: Selected item cannot fit into memory grub> quit quit _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
boot problem after disk change on raid1
The system works just fine now. I think there was a disk check or something at boot time which takes 15-20 minutes (I rarely reboot the system once or twice a year), and it made me think that the system does not boot.
Thanks for your help. Bunyamin. 2011/9/8 Bünyamin İzzet <bunyamin.izzet@gmail.com> On Thu, Sep 8, 2011 at 8:11 AM, Devin Reade <gdr@gno.org> wrote: Bünyamin Ýzzet <bunyamin.izzet@gmail.com> wrote: > On Wed, Sep 7, 2011 at 11:38 PM, Devin Reade <gdr@gno.org> wrote: > [snip] >> * * * * * * * * * * * *# grub >> * * * * * * * * * * * *grub> device (hd0) /dev/sdb >> * * * * * * * * * * * *grub> root (hd0,0) >> * * * * * * * * * * * *grub> setup (hd0) >> * * * * * * * * * * * *grub> quit > > It still does not boot. I could not see the error message, because it is a > dedicated server and I am not sitting at the monitor of the server. So I > type the lines in grub.conf manually to see the error (I'm not sure if it is > the right thing to see the error). If you mean that you typed the lines I gave above into grub.conf, then that was not what was intended (and I doubt that it would work). *My intent was that you get the system booted and running normally (perhaps via the rescue disk), and after that execute 'grub' interactively and issue those commands. *Devin As you said, I booted the system via rescue disk, and execute grub and issue those commands. Then, I reboot the system, but it does not boot. Then I searched on google about logging grub errors, which I could not find anything useful (meybe I did not look enough). So that, in rescue system, I execute grub and type commands in grub.conf (results are below) to see which error occurs. # grub Probing devices to guess BIOS drives. This may take a long time. GNU GRUB version 0.97 (640K lower / 3072K upper memory) [ Minimal BASH-like line editing is supported. For the first word, TAB lists possible command completions. Anywhere else TAB lists the possible completions of a device/filename.] grub> root (hd1,0) root (hd1,0) Filesystem type is ext2fs, partition type 0xfd grub> kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 kernel /vmlinuz-2.6.18-238.19.1.el5 ro root=/dev/md1 vga=0x317 [Linux-bzImage, setup=0x1e00, size=0x1fe01c] grub> initrd /initrd-2.6.18-238.19.1.el5.img initrd /initrd-2.6.18-238.19.1.el5.img Error 28: Selected item cannot fit into memory grub> quit quit _______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos |
| All times are GMT. The time now is 04:41 PM. |
VBulletin, Copyright ©2000 - 2013, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.