FAQ Search Today's Posts Mark Forums Read
» Video Reviews

» Linux Archive

Linux-archive is a website aiming to archive linux email lists and to make them easily accessible for linux users/developers.


» Sponsor

» Partners

» Sponsor

Go Back   Linux Archive > CentOS > CentOS

 
 
LinkBack Thread Tools
 
Old 10-22-2008, 01:53 PM
partha chowdhury
 
Default SCSI error: return code = 0x10070000

I have just bought a 120GB external usb drive but after plugging it in
it is not getting mounted.


lines from /var/log/messages:

Oct 22 18:54:49 station2 kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2
Oct 22 18:54:49 station2 kernel: usb 1-2: configuration #1 chosen from 1 choice
Oct 22 18:54:49 station2 kernel: scsi4 : SCSI emulation for USB Mass Storage devices
Oct 22 18:54:54 station2 kernel: Vendor: ST312002 Model: 2A Rev: 0 0
Oct 22 18:54:54 station2 kernel: Type: Direct-Access ANSI SCSI revision: 00
Oct 22 18:54:54 station2 kernel: SCSI device sdd: 234441648 512-byte hdwr sectors (120034 MB)
Oct 22 18:54:54 station2 kernel: sdd: Write Protect is off
Oct 22 18:54:54 station2 kernel: sdd: assuming drive cache: write through
Oct 22 18:54:54 station2 kernel: SCSI device sdd: 234441648 512-byte hdwr sectors (120034 MB)
Oct 22 18:54:54 station2 kernel: sdd: Write Protect is off
Oct 22 18:54:54 station2 kernel: sdd: assuming drive cache: write through
Oct 22 18:54:54 station2 kernel: sdd:<6>sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: Dev sdd: unable to read RDB block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0
Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0
Oct 22 18:54:54 station2 kernel: unable to read partition table
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: Attached scsi disk sdd
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: Attached scsi generic sg3 type 0
Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000
Oct 22 18:54:54 station2 kernel: end_request: I/O error


upon searching in the forum i came accross this tread
http://www.centos.org/modules/newbb/viewtopic.php?topic_id=9887&forum=29&post_id=31541 #forumpost31541


but it has gone unanswered for two years.

Google search gives result all of which involves moving to a newer
kernel.For the matter the drive gets mounted under fedora 9 - but i want
to use it with CentOS.


here is my lspci -v


00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Capabilities: [dc] HyperTransport: MSI Mapping

00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0
I/O ports at 0900 [size=256]

00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: 66MHz, fast devsel, IRQ 10
I/O ports at dc00 [size=64]
I/O ports at 0600 [size=64]
I/O ports at 0700 [size=64]
Capabilities: [44] Power Management version 2

00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 58
Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2

00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 233
Memory at feafec00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2

00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 66
Memory at feafd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2

00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 50
Memory at feafe800 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2

00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: feb00000-febfffff
Capabilities: [b8] #0d [0000]
Capabilities: [8c] HyperTransport: MSI Mapping

00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 233
I/O ports at d480 [size=8]
I/O ports at d400 [size=4]
I/O ports at d080 [size=8]
I/O ports at d000 [size=4]
I/O ports at cc00 [size=16]
Memory at feafa000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [44] Power Management version 2
Capabilities: [8c] #12 [0010]

00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 90
Memory at feafc000 (32-bit, non-prefetchable) [size=4K]
I/O ports at c880 [size=8]
Memory at feafe400 (32-bit, non-prefetchable) [size=256]
Memory at feafe000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable+
Capabilities: [6c] HyperTransport: MSI Mapping

00:0b.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:0e.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:0f.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:10.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:11.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
Capabilities: [40] #0d [0000]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+
Capabilities: [60] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0

00:12.0 VGA compatible controller: nVidia Corporation GeForce 7050 PV / nForce 630a (rev a2) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Unknown device 82b3
Flags: bus master, 66MHz, fast devsel, laten



Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at fc000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: [80] HyperTransport: Host or Secondary Interface

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
Capabilities: [f0] #0f [0010]

01:06.0 Multimedia audio controller: Creative Labs [SB Live! Value] EMU10k1X
Subsystem: Creative Labs Unknown device 1001
Flags: bus master, medium devsel, latency 64, IRQ 82
I/O ports at ec00 [size=32]
Capabilities: [dc] Power Management version 2

01:07.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 8b)
Subsystem: D-Link System Inc Unknown device 1405
Flags: bus master, medium devsel, latency 64, IRQ 74
I/O ports at e800 [size=256]
Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Power Management version 2

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-22-2008, 03:13 PM
"John"
 
Default SCSI error: return code = 0x10070000

partha chowdhury [kira.laucas@gmail.com] Writes:

Subsystem: ASUSTeK Computer Inc.
--------------------------------------
JohnStanley Writes:
Have you taken a look at asus.com for kernel modules for the USB integration
on the Asus Mother Board. They do offer drivers for various on board
controlers and NIC Cards. If perhapse they do have then you will have to
compile and install them yourself. They have gotten really decent at *nix
drivers.

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-22-2008, 03:17 PM
"John"
 
Default SCSI error: return code = 0x10070000

I have just bought a 120GB external usb drive but after plugging it in
it is not getting mounted.

JohnStanley Writes:

Also look in your BIOS for your USB Settings. Make sure it is Set for Legacy
Compatablity so it can run the older 1.0USB and also 2.0USB.

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-22-2008, 03:57 PM
partha chowdhury
 
Default SCSI error: return code = 0x10070000

John wrote:

partha chowdhury [kira.laucas@gmail.com] Writes:

Subsystem: ASUSTeK Computer Inc.
--------------------------------------
JohnStanley Writes:
Have you taken a look at asus.com for kernel modules for the USB integration
on the Asus Mother Board. They do offer drivers for various on board
controlers and NIC Cards. If perhapse they do have then you will have to
compile and install them yourself. They have gotten really decent at *nix
drivers.

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos


they only have audio driver for linux for the motherboard.
_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-22-2008, 03:59 PM
partha chowdhury
 
Default SCSI error: return code = 0x10070000

John wrote:
I have just bought a 120GB external usb drive but after plugging it in
it is not getting mounted.


JohnStanley Writes:

Also look in your BIOS for your USB Settings. Make sure it is Set for Legacy
Compatablity so it can run the older 1.0USB and also 2.0USB.

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos

the manual for the usb drive says it is usb 2.0 and bios is set to
autodetect usb type.

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-22-2008, 04:37 PM
"John"
 
Default SCSI error: return code = 0x10070000

Also look in your BIOS for your USB Settings. Make sure it is Set for Legacy
> Compatablity so it can run the older 1.0USB and also 2.0USB.
>

the manual for the usb drive says it is usb 2.0 and bios is set to
autodetect usb type.

JohnStanley Writes:
Well, I am out of sejustions then. Have you used any other USB drives in
that machine? Beside Seagate?

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-22-2008, 06:50 PM
partha chowdhury
 
Default SCSI error: return code = 0x10070000

John wrote:

Also look in your BIOS for your USB Settings. Make sure it is Set for Legacy

Compatablity so it can run the older 1.0USB and also 2.0USB.



the manual for the usb drive says it is usb 2.0 and bios is set to
autodetect usb type.


JohnStanley Writes:
Well, I am out of sejustions then. Have you used any other USB drives in
that machine? Beside Seagate?

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos

i have another 80G external samsung drive from 2 years and it works
without problem .

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 
Old 10-23-2008, 05:14 AM
"John"
 
Default SCSI error: return code = 0x10070000

behalf of; partha chowdhury [kira.laucas@gmail.com]

>i have another 80G external samsung drive from 2 years and it works
>without problem .

JohnStanley Writes:

You could very well be just having an issue wich involves the drive firware
not being compatable with the operatting system since the other one does
work.

As a side note I have a USB Drive and a Thumb drive that will work in
windows but not linux. What I did was found one brand and model that worked
and bought extra ones for the linux systems.

_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
 

Thread Tools




All times are GMT. The time now is 02:44 AM.

VBulletin, Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2007, Crawlability, Inc.
Copyright 2007 - 2008, www.linux-archive.org